EN 15085-4-2007 英文版 Railway applications - Welding of railway vehicles and components - Par T 4 Production requirements.pdf

《EN 15085-4-2007 英文版 Railway applications - Welding of railway vehicles and components - Par T 4 Production requirements.pdf》由会员分享，可在线阅读，更多相关《EN 15085-4-2007 英文版 Railway applications - Welding of railway vehicles and components - Par T 4 Production requirements.pdf（17页珍藏版）》请在麦多课文档分享上搜索。

1、EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 15085-4October 2007ICS 45.060.01; 25.160.10English VersionRailway applications - Welding of railway vehicles andcomponents - Part 4: Production requirementsApplications ferroviaires - Soudage des vhicules et descomposants ferroviaires - Partie 4: Exi

2、gences deproductionBahnanwendungen - Schweien von Schienenfahrzeugenund -fahrzeugteilen - Teil 4: FertigungsanforderungenThis European Standard was approved by CEN on 18 August 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving th

3、is EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (E

4、nglish, French, German). A version in any other language made by translationunder the respons bility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria

5、, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATION

6、COMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2007 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 15085-4:2007: EEN 15085-4:2007 (E) 2 Contents Page Foreword.3 Int

7、roduction .4 1 Scope .5 2 Normative references .5 3 Terms and definitions .6 4 Preparation before welding .6 4.1 Welding planning documents.6 4.2 Production weld tests .8 5 Requirements for welding.10 5.1 General.10 5.2 General requirements.10 5.3 Welding consumables.13 5.4 Parent metals .14 5.5 Wel

8、ding processes .15 6 Special requirements for maintenance welding of railway vehicles .16 6.1 General rules for maintenance welding .16 6.2 Testing and documentation.16 Bibliography .17 EN 15085-4:2007 (E) 3 Foreword This document (EN 15085-4:2007) has been prepared by Technical Committee CEN/TC 256

9、 “Railway applications”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2008, and conflicting national standards shall be withdrawn at the latest by

10、 April 2008. This series of European Standards EN 15085 Railway applications Welding of railway vehicles and components consists of the following parts: Part 1: General Part 2: Quality requirements and certification of welding manufacturer Part 3: Design requirements Part 4: Production requirements

11、Part 5: Inspection, testing and documentation Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Re

12、gulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Ne

13、therlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 15085-4:2007 (E) 4 Introduction Welding is a special process in the manufacture of railway vehicles and their parts. The required provisions for this process are laid down in the s

14、tandards series EN ISO 3834. The basis of these provisions are the basic technical welding standards in respect of the special requirements for the construction of railway vehicles. This standard is aimed at defining the terms of enforcement applicable to European Standards, it should not be constru

15、ed as a substitute to these standards. This standard can also be used by internal and external parties, including certification bodies, to assess the organisations ability to meet customer, regulatory and the organisations own requirements. EN 15085-4:2007 (E) 5 1 Scope This series of standards appl

16、ies to welding of metallic materials in the manufacture and maintenance of railway vehicles and their parts. This part of the series describes the production requirements (i.e. preparation and execution) of the welding work. 2 Normative references The following referenced documents are indispensable

17、 for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 287-1, Qualification test of welders Fusion welding Part 1: Steels EN 1011 (all parts), Welding Re

18、commendations for welding of metallic materials EN 10204:2004, Metallic products Types of inspection documents EN 13479, Welding consumables General product standard for filler metals and fluxes for fusion welding of metallic materials EN 15085-1:2007, Railway applications - Welding of railway vehic

19、les and components - Part 1: General EN 15085-3:2007, Railway applications Welding of railway vehicles and components Part 3: Design requirements EN ISO 544, Welding consumables - Technical delivery conditions for welding filler materials - Type of product, dimensions, tolerances and markings (ISO 5

20、44:2003) EN ISO 4063:2000, Welding and allied processes - Nomenclature of processes and reference numbers (ISO 4063:1998) EN ISO 9013:2002, Thermal cutting - Classification of thermal cuts - Geometrical product specification and quality tolerances (ISO 9013:2002) EN ISO 9606-2, Qualification test of

21、 welders - Fusion welding - Part 2: Aluminium and aluminium alloys (ISO 9606-2:2004) EN ISO 9606-3, Approval testing of welders - Fusion welding - Part 3: Copper and copper alloys (ISO 9606-3:1999) EN ISO 9606-4, Approval testing of welders - Fusion welding - Part 4: Nickel and nickel alloys (ISO 96

22、06-4:1999) EN ISO 9606-5, Approval testing of welders - Fusion welding - Part 5: Titanium and titanium alloys, zirconium and zirconium alloys (ISO 9606-5:2000) EN ISO 14555, Welding - Arc stud welding of metallic materials (ISO 14555:2006) CEN ISO/TR 15608:2005, Welding - Guidelines for a metallic m

23、aterials grouping system (ISO/TR 15608:2005) EN 15085-4:2007 (E) 6 EN ISO 15609 (all parts), Specification and qualification of welding procedures for metallic materials Welding procedure specification EN ISO 15610 Specification and qualification of welding procedures for metallic materials - Qualif

24、ication based on tested welding consumables (ISO 15610:2003) EN ISO 15611, Specification and qualification of welding procedures for metallic materials - Qualification based on previous welding experience (ISO 15611:2003) EN ISO 15612 Specification and qualification of welding procedures for metalli

25、c materials - Qualification by adoption of a standard welding procedure (ISO 15612:2004) EN ISO 15613, Specification and qualification of welding procedures for metallic materials - Qualification based on pre-production welding test (ISO 15613:2004) EN ISO 15614 (all parts) 1)Specification and quali

26、fication of welding procedures for metallic materials Welding procedure test EN ISO 15620, Welding - Friction welding of metallic materials (ISO 15620:2000) EN ISO 17652-1, Welding - Test for shop primers in relation to welding and allied processes - Part 1: General requirements (ISO 17652-1:2003) E

27、N ISO 17652-2, Welding - Test for shop primers in relation to welding and allied processes - Part 2: Welding properties of shop primers (ISO 17652-2:2003) 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 15085-1:2007 apply. 4 Preparation before welding

28、 4.1 Welding planning documents 4.1.1 General Welding planning documents shall be prepared by the manufacturers with the assistance of the recognised welding coordinator Level A for new and converted vehicles and maintenance of rail vehicles (see EN 15085-2). Type, scope and time of the submission a

29、nd inspection should be agreed between customer and manufacturer. Welding planning documents may include working plans, welding sequence plans, test planning documents and welding procedure specifications. 4.1.2 Working plans For the production of railway vehicles it is necessary to have working pla

30、ns for the following sub-assemblies: bogie (sub-assemblies, assembly); 1) For railway applications, only EN ISO 15614-1, EN ISO 15614-2, prEN ISO 15614-3, EN ISO 15614-4, EN ISO 15614-7, EN ISO 15614-11, EN ISO 15614-12 and EN ISO 15614-13 are relevant. EN 15085-4:2007 (E) 7 underframe (with sub-ass

31、emblies); body (side wall, end wall, roof); further sub-assemblies with high safety and functional requirements (e.g. cardan shafts, brake cross members, motor housing, hollow shaft drive, drawbar coupling, bogie pivot pin, cross bearer). 4.1.3 Other welding planning documents For more complicated a

32、ssemblies welding sequence plans are necessary, e.g. for: bogies (bogie bolster, bogie centre plate including bogie pivot pin member, solebar, headstock, bogie pivot pin cross member, traction bar coupling, assembly of solebar and cross member); underframe (including cross member, solebar, headstock

33、, bogie pivot pin cross member, traction bar coupling). Standardised welding sequence plans (that applies for different types of vehicles) are also allowed. Furthermore, other welding planning documents may be necessary (e.g. tacking sequence plans, repairing plans, test plans, documents for jigs an

34、d tools, remarks for protection of labour and health, plans for separating of damaged parts, special instructions for electronic parts). These details shall be determined by the responsible welding coordinator and/or the customer. 4.1.4 Welding procedure specification For welds with welding performa

35、nce classes CP A, CP B, CP C1, CP C2 and CP C3, welding procedure specifications according to EN ISO 15609-1 to EN ISO 15609-5, to EN ISO 14555 or to EN ISO 15620 are necessary. For weld performance class CP D this is only necessary if the customer demands it. Dependent on the weld performance class

36、es according to EN 15085-3, the following evidences are necessary for the welding procedure specification: Weld performance class CP A: Evidence according to any of the following standards: EN ISO 156142)or EN ISO 15620; EN ISO 15613 only if a WPQR according to EN ISO 15614 exists; for materials wit

37、h Reh 500 MPa or fully mechanised welding processes: EN ISO 15614. For the WPQR the acceptance criteria of weld performance class CP A (EN 15085-3:2007, Table 5 and Table 6) shall be fulfilled. Weld performance classes CP B, CP C1, CP C2: Evidence according to any of the following standards: EN ISO

38、15613, EN ISO 14555, EN ISO 15620; if necessary for component or the material: EN ISO 15614. Weld performance class CP C3: Evidence according to any of the following standards: EN ISO 15610, EN ISO 15611, EN ISO 15612, EN ISO 15613, EN ISO 14555, EN ISO 15620; if necessary for component or the mater

39、ial: EN ISO 15614. Weld performance class CP D: According to the requirements of the customer. In general, every WPS shall be covered by a WPQR, except for weld performance class CP D unless specified in the contract. 2) See footnote 1). EN 15085-4:2007 (E) 8 NOTE For the validity of WPS and WPQR ac

40、cording to EN ISO 15614-1 and EN ISO 15614-2, see Introduction of EN ISO 15614-1:2004 and EN ISO 15614-2:2005. 4.2 Production weld tests 4.2.1 General 4.2.1.1 Aim and objective of production weld tests If necessary, production weld tests shall be carried out. The aim and objective of production weld

41、 tests is: to check and ensure that the design is satisfactory as specified in EN 15085-3; to prove the welding conditions; to demonstrate the skill of the welders; to demonstrate the quality of the weld. One production weld test can be used for several tasks indicated above. 4.2.1.2 Realization and

42、 amount of testing of production weld test The production weld test shall be carried out under the same manufacturing conditions as the real product. They shall be carried out under the supervision of the responsible welding coordinator and they shall be documented. Production weld tests should be welded in accordance with EN ISO 15613. They may be welded separately as test plates,