VA 08 36 13-2011 SECTIONAL DOORS.pdf

《VA 08 36 13-2011 SECTIONAL DOORS.pdf》由会员分享，可在线阅读，更多相关《VA 08 36 13-2011 SECTIONAL DOORS.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、10-11 08 36 13 - 1 SECTION 08 36 13 SECTIONAL DOORS Spec WRITER NOTE: Delete between /_/, if not applicable to project. Also delete all other items or paragraph not applicable in the section and renumber the paragraphs. PART 1 - GENERAL 1.1 DESCRIPTION: This section specifies electrically operated t

2、hermal insulated sectional overhead steel doors. 1.2 RELATED WORK: A. Overhead roll-up doors: Section 08 33 00, COILING DOORS AND GRILLES. B. Lock cylinders for cylindrical locks: Section 08 71 00, DOOR HARDWARE. C. Field painting: Section 09 91 00, PAINTING. D. Electrical Installation: Section 26 0

3、5 11, REQUIREMENTS FOR ELECTRICAL INSTALLATIONS/ Section 27 05 11, REQUIREMENTS FOR COMMUNICATIONS INSTALLATIONS/ Section 28 05 11, REQUIREMENTS FOR ELECTRONIC SAFETY AND SECURITY INSTALLATIONS. 1.3 MANUFACTURERS AND INSTALLERS QUALIFICATIONS: A. Manufacturers regularly engaged in manufacturing item

4、s of type specified. B. Installers under direct supervision of manufacturers representative or trained personnel. 1.4 SUBMITTALS: A. Submit in accordance with Section 01 33 23, SHOP DRAWINGS, PRODUCT DATA, AND SAMPLES. B. Shop Drawings: 1. Details of construction, accessories and hardware, electrica

5、l and mechanical items, supporting brackets for motors, location, and ratings of motors, and safety devices. 2. Wiring diagrams for motors and controls, including wiring diagram for door, showing electrical interlock for motor with manually operated dead lock. C. Manufacturers Literature and Data: 1

6、. Brochures or catalog cuts. 2. Manufacturers installation procedures and instructions. 3. Maintenance instructions, parts list. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-10-11 08 36 13 - 2 D. Certificates: 1. Attesting door, anchors and hardwa

7、re will withstand the horizontal loads specified. 2. Attesting door complies with thermal performance, air infiltration, and water infiltration requirements. 1.5 APPLICABLE PUBLICATIONS: A. Publications listed below form a part of this specification to the extent referenced. Publications are referen

8、ced in the text by the basic designation only. B. American Society for Testing and Materials (ASTM): A36/A36M-08 Structural Steel A227/A227M-06 Steel Wire, Cold-Drawn for Mechanical Springs A229/229M-99(R2005) Steel Wire, Oil-Tempered for Mechanical Springs A653-10 Steel Sheet, Zinc-Coated (Galvaniz

9、ed) or Zinc Iron Alloy Coated (Galvanized) by the Hot Dip Process C1036-06 . Flat Glass E84-10 . Surface Burning Characteristics of Building Materials E283-04 Determining the Rate of Air Leakage Through Exterior Windows, Curtain Walls, and Doors Under Specified Pressure Difference Across the Specime

10、n E330-02(R2010) . Structural Performance of Exterior Windows, Curtain Walls, and Doors by the Uniform Static Air Pressure Difference. E331-00(R2009) . Water Penetration of Exterior Windows, Curtain Walls, and Doors by the Uniform Static Air Pressure Difference. C. American National Standards Instit

11、ute and Door and Access Systems Manufacturers Association (ANSI/DASMA): 102-04 . Sectional Overhead Type Doors. D. National Electrical Manufacturers Association (NEMA): ICS 2-00 (R2005) . Industrial Control and Systems: Controllers, Contactors, and Overload Relays MG 1-10 Motors and Generators E. Na

12、tional Fire Protection Association (NFPA): 70-11 National Electrical Code Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-10-11 08 36 13 - 3 F. National Association of Architectural Metal Manufacturers (NAAMM): AMP 500-06 . Metal Finishes Manual PART

13、 2 - PRODUCTS 2.1 MATERIALS: A. Steel: ASTM A653 for forming operations. ASTM A36 for structural sections. B. Hard Drawn Spring wire: ASTM A227. C. Oil Tempered Spring wire: ASTM A229. D. Glass: ASTM C1036 1. Clear Glass: Type 1, Class 1, Quality q5, 6 mm (1/4 inch) thick. 2. Fabricated into sealed

14、insulating glass 25 mm (one inch) thick. E. Weather-strips, Gaskets, and Thermal Breaks: 1. Neoprene, EPDM, PVC, silicone rubber, or other low conductance material. 2. Standard with door manufacturer. 2.2 DESIGN REQUIREMENTS: SPEC WRITER NOTE: Use not less than 960 Pa (20 pounds per square foot) for

15、 wind load. Insert higher loads for locations when required by code. A. Wind Load: Design to withstand a horizontal or wind pressure of 960 Pa (20 pounds per square foot) of door area without damage when tested in accordance with ASTM E330. B. Thermal Performance: Maximum U value of 0.14 for door wh

16、en tested in accordance with ASTM C236. C. Air Infiltration: Maximum of 0.10 cfm at 24 Km (15 miles per hour) wind speed per foot of crack between door sections and door perimeter opening when tested in accordance with ASTM E283. D. Water Infiltration: No infiltration when tested in accordance with

17、ASTM E331. E. Comply with ANSI/NAGDM 102, for an Industrial door and specified design criteria, inside face mounted with tracks at jambs set back a sufficient distance to provide a clear opening when door is in open position. F. Operation-Cycle Requirements: Door components and operators to operate

18、for not less than 10,000 cycles. 2.3 FABRICATION: A. Steel Door Sections: 1. Formed of hot-dipped galvanized steel. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-10-11 08 36 13 - 4 2. Meeting rails: interlocking joints with thermal breaks separatin

19、g face sheets formed to provide weathertight closure and alignment for full width of door. 3. Height of sections: Not to exceed 600 mm (24 inches) may be varied to suit door height. 4. Install glazing panels where indicated using rubber thermal break gaskets standard with door manufacturer. 5. Insul

20、ation shall have a flame spread rating of not more than 25 and a smoke development factor of not more than 50 when tested in accordance with ASTM E 84. 6. Reinforced for hardware anchorage with not less than 10 gage galvanized steel. B. Tracks: 1. Manufacturers standard formed of galvanized steel. 2

21、. Minimum of 14 gage for 50 mm (2 inch) tracks and 12 gage for 75 mm (3 inch) tracks. 3. Vertical tracks fabricated with adjustable brackets for mounting at incline to continuous steel angle wall bracket. 4. Horizontal track: Reinforce with continuous steel angle anchored to vertical steel angle wal

22、l bracket and to ceiling angle supports. Use vertical and cross or diagonal braced to obtain rigid installation of horizontal track. 5. Use not less than 13 gage galvanized steel angles. C. Hardware: 1. Manufacturers standard hinges, brackets, rollers, locking devices and other hardware required for

23、 a complete installation. 2. Hinges and roller brackets minimum of 13 gage galvanized steel. 3. Use rollers with ball bearings and case hardened races. 4. Positive locking device to receive cylinder lock, specified in Section 08 71 00, DOOR HARDWARE, with interlocking switch to motor operator. 2.4 E

24、LECTRIC MOTOR OPERATORS: A. Complete with electric motor, machine cut reduction gears, steel chain and sprockets, magnetic brake, overload protection, brackets, push button controls, limit switches, magnetic reversing contactor, and other accessories necessary for proper operation, including emergen

25、cy manual operator. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-10-11 08 36 13 - 5 B. Design: 1. Design the operator for motor removal without disturbing the limit-switch timing and without affecting the emergency manual operators. 2. Make provis

26、ion for emergency manual operation of door by chain-gear mechanism in case of electrical failure. 3. Arrange the emergency manual operating mechanism to immediately be put into and out of operation from the floor with a mechanical device to disconnect the motor from the operating mechanism when the

27、emergency manual operating mechanism is engaged and not affect the timing of the limit switches. 4. Provide interlock with motor to prevent motor from operating when manual locks are activated. C. Motors: 1. Motor conform to NEMA MG 1, maximum operation 3600 rpm. 2. Suitable for operation on current

28、 specified in Division 26, ELECTRICAL. 3. Use high starting torque, reversible type, of sufficient horsepower and torque output to move the door in either direction from door position, and produce door travel speed range of 0.20 to 0.30 m per second (8 to 12 inches per second), without exceeding the

29、 rated capacity. 4. Single-phase motors shall not have commutation or more than one starting contact. 5. Motor Enclosures: Drip proof type or NEMA TENV type. D. Controls: 1. Control equipment: NEMA 2. 2. Control enclosures: NEMA ICS 6, Type 12 or Type 4, except that contractor enclosures may be Type

30、 1. Use weatherproof corrosion-resistant covers for exterior locations. 3. At door motors use an enclosed, across-the-line type, magnetic reversing contactor, thermal overload protection, solenoid operated brake, limit switches, and remote control switches at locations indicated. 4. Control switches

31、: a. Three push button type on interior, unless noted to be key activated. b. Buttons marked, OPEN, CLOSE and STOP. c. The OPEN and STOP buttons: Momentary pressure or contact type. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-10-11 08 36 13 - 6 d

32、. The CLOSE button: Constant pressure type. e. Use key activated switch on exterior requiring constant pressure to operate. f. Limit switches: Manufacturers standard, position of switches readily adjustable. 5. Operation: a. Open door upon activation of Open switch. b. Close door only when constant

33、pressure applied. c. When the door is in motion, and the STOP button is pressed, door shall stop instantly and remain in the stop position; from stop position, door may be operated in either direction by OPEN or CLOSE button. d. Limit switches automatically stop doors at their fully open and closed

34、positions. 6. Push buttons full-guarded to prevent accidental operation. 7. Transformer: a. Use a control transformer in power circuits to reduce the voltage on control circuits to 120 volts or less. b. Conform to NEMA ST 20. 8. Electrical Components: Conform to NFPA 70. 9. Safety Device: a. Bottom

35、door edge weather-strip safety device to immediately stop and reverse the door closing to full open position upon contact with an obstruction. Door is to open upon failure of device, component of device or component of control system. b. The door closing circuit shall be electrically locked out and

36、door to remain capable of manual operation until the failure or damage has been corrected. c. Do not use as a limit switch. d. Safety device connecting cable to motor to be flexible type SO cable with spring loaded automatic take up reel or equivalent device, as required for proper operation of the

37、doors. 2.5 FINISHES: A. Steel: 1. Comply with NAAMMs Metal Finishes Manual. 2. Clean surfaces free of scale, rust, oil and grease. 3. Non-galvanized steel: Pretreatment to assure maximum paint adherence. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-

38、,-10-11 08 36 13 - 7 4. Galvanized steel: Apply phosphate treatment. 5. Apply shop prime coat of corrosion inhibitive paint on exposed surfaces after fabrication. 6. Apply finish paint on color scheduled when specified in Section 09 06 00, SCHEDULE FOR FINISHES. 7. Do not paint track, rollers, hinge

39、s, or locks. PART 3 - EXECUTION 3.1 INSTALLATION: A. Install in accordance with approved shop drawings and manufacturers instructions. For electrical work, see Section 26 05 11, REQUIREMENTS FOR ELECTRICAL INSTALLATIONS/ Section 27 05 11, REQUIREMENTS FOR COMMUNICATIONS INSTALLATIONS/ Section 28 05

40、11, REQUIREMENTS FOR ELECTRONIC SAFETY AND SECURITY INSTALLATIONS. B. Locate anchors and inserts for tracks, brackets, motors, switches, hardware, and other accessories accurately. C. Securely attach tracks to adjoining construction with not less than 9 mm (3/8 inch) diameter bolts, spaced near each

41、 end and not over 600 mm (24 inches) apart. D. Locate control switches where shown at least five feet above the floor line so that the operator will have complete visibility of the door. E. Lubricate, properly adjust and demonstrate door to operate freely. F. Upon completion, door openings shall be

42、weathertight and doors shall be free from warp, twists, or distortion. 3.2 REPAIR: A. Repair zinc-coated surfaces both bare and painted, by the application of galvanizing repair compound. B. Spot prime and apply finish paint to all repairs. - - - E N D - - - Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-