UL 66-2002 UL Standard for Safety Fixture Wire (First Edition Reprint with Revisions Through and Including April 12 2016)《固定金属线》.pdf

《UL 66-2002 UL Standard for Safety Fixture Wire (First Edition Reprint with Revisions Through and Including April 12 2016)《固定金属线》.pdf》由会员分享，可在线阅读，更多相关《UL 66-2002 UL Standard for Safety Fixture Wire (First Edition Reprint with Revisions Through and Including April 12 2016)《固定金属线》.pdf（62页珍藏版）》请在麦多课文档分享上搜索。

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULUL 66Fixture WireUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIB

2、UTION WITHOUT PERMISSION FROM ULUL Standard for Safety for Fixture Wire, UL 66First Edition, Dated April 16, 2002Summary of Topics:This revision of ANSI/UL 66 is being issued to:Add the Aging Condition for the Flexing Test of Nylon Jacketed Types TFN and TFFNText that has been changed in any manner

3、or impacted by ULs electronic publishing system is markedwith a vertical line in the margin. Changes in requirements are marked with a vertical line in the marginand are followed by an effective date note indicating the date of publication or the date on which thechanged requirement becomes effectiv

4、e.The revised requirements are substantially in accordance with Proposal(s) on this subject datedSeptember 23, 2011.All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, ortransmitted in any form by any means, electronic, mechanical photocopying, recording

5、, or otherwisewithout prior permission of UL.UL provides this Standard as is without warranty of any kind, either expressed or implied, including butnot limited to, the implied warranties of merchantability or fitness for any purpose.In no event will UL be liable for any special, incidental, consequ

6、ential, indirect or similar damages,including loss of profits, lost savings, loss of data, or any other damages arising out of the use of or theinability to use this Standard, even if UL or an authorized UL representative has been advised of thepossibility of such damage. In no event shall ULs liabi

7、lity for any damage ever exceed the price paid forthis Standard, regardless of the form of the claim.Users of the electronic versions of ULs Standards for Safety agree to defend, indemnify, and hold ULharmless from and against any loss, expense, liability, damage, claim, or judgment (including reaso

8、nableattorneys fees) resulting from any error or deviation introduced while purchaser is storing an electronicStandard on the purchasers computer system.The requirements in this Standard are now in effect, except for those paragraphs, sections, tables, figures,and/or other elements of the Standard h

9、aving future effective dates as indicated in the note following theaffected item. The prior text for requirements that have been revised and that have a future effective dateare located after the Standard, and are preceded by a SUPERSEDED REQUIREMENTS notice.NOVEMBER 21, 2011 UL 66 tr1UL COPYRIGHTED

10、 MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULNOVEMBER 21, 2011 UL 66tr2No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULAPRIL 16, 2002(Title Page Reprinted: November 21, 2011)1UL

11、 66Fixture WireFirst EditionApril 16, 2002This ANSI/UL Standard for Safety consists of the First Edition including revisionsthrough November 21, 2011.The most recent designation of ANSI/UL 66 as an American National Standard(ANSI) occurred on November 21, 2011. ANSI approval for a standard does noti

12、nclude the Cover Page, Transmittal Pages, Title Page, or effective dateinformation.Comments or proposals for revisions on any part of the Standard may besubmitted to UL at any time. Proposals should be submitted via a ProposalRequest in ULs On-Line Collaborative Standards Development System (CSDS)at

13、 http:/.ULs Standards for Safety are copyrighted by UL. Neither a printed nor electroniccopy of a Standard should be altered in any way. All of ULs Standards and allcopyrights, ownerships, and rights regarding those Standards shall remain thesole and exclusive property of UL.COPYRIGHT 2011 UNDERWRIT

14、ERS LABORATORIES INC.ANSI/UL 66-2011UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULJUNE 7, 2005FIXTURE WIRE - UL 662No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULC

15、ONTENTSINTRODUCTION1 Scope .72 Units of Measurement .73 References .74 Index Tables .7CONSTRUCTION5 Materials 18A6 Conductor .18A6.1 Metal .18A6.2 Sizes .18B6.3 Stranding .18B6.4 Size verification .196.5 Continuity 206.6 Joints 206.7 Metal coating .207 Separator .208 Insulation .218.1 Material and a

16、pplication 218.2 Properties 228.3 Thicknesses 239 Jacket on Types TFN and TFFN .2310 Covering on Other Wire Types .2410.1 Elective braid on Types TF, TFF, and RFHH-2 and on XL-insulated Types RFHH-3,RFH-2, and FFH-2 .2410.2 Braid or other covering on Types PF, PFF, PGF, PGFF, SF-1, SF-2, SFF-1, andS

17、FF-2 .2410.3 Extruded covering on silicone-insulated Type RFHH-3 and braid, wrap, or extrudedcovering on rubber-insulated Types RFH-2 and FFH-2 24APERFORMANCE11 Continuity Test of Conductor .3212 D-C Resistance Test of Conductor 3213 Spark Test .3514 Deformation Test .3515 Cold Bend Test .3716 Test

18、for Insulation Resistance at 60.0F (15.6C) .3817 Flame Tests for VW-1 Wire 4118 Vertical Flame Test .4119 Flexing Test of Nylon Jacket on Types TFN and TFFN 4120 Durability Test of Ink Printing .41JUNE 7, 2005 FIXTURE WIRE - UL 66 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDI

19、STRIBUTION WITHOUT PERMISSION FROM ULMARKINGS21 Polarity Identification 4222 Legibility of Printing 42A23 Sequence of Printed Markings 42A24 Responsible Organization and Factory Identification .42A25 Temperature Identification 42B26 Identification of Types TFN and TFFN That Are Resistant to Oil or O

20、il and Gasoline 4427 Identification of VW-1 Wire .4528 Tag, Reel, and Carton Markings 4529 Current Designation .4630 Date of Manufacture 46SUPPLEMENT SA - U.S. GOVERNMENT REQUIREMENTS AND ORDERING INSTRUCTIONS FORACQUISITION OF FIXTURE WIRESA1 Scope SA1SA2 Requirements .SA1SA3 Quality Assurance .SA2

21、SA4 Packaging SA2SA5 Ordering documents .SA3NOVEMBER 21, 2011FIXTURE WIRE - UL 664UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULAPRIL 16, 2002 FIXTURE WIRE - UL 66 5No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRO

22、DUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULThis page intentionally left blank.JUNE 7, 2005FIXTURE WIRE - UL 666UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULINTRODUCTION1 Scope1.1 This standard states basic construction, test, and mark

23、ing requirements for fixture wires. Fixture wiresare single conductor and are of the following types:600 volt Types: PTF, PTFF, PAF, PAFF, KF-2, KFF-2, PF, PFF, PGF, PGFF, SF-2, SFF-2, ZF, ZFF,ZHF, TF, TFF, TFN, TFFN, RFH-2, FFH-2, RFHH-2, and RFHH-3300 volt Types: KF-1, KFF-1, SF-1, SFF-1, XF, and

24、XFFThese types are for use as specified in Article 402 and other applicable parts of the National ElectricalCode (NEC), ANSI / NFPA 70. These types are as described individually in index Tables 4.1 4.9 of thisstandard.1.1 revised June 7, 20052 Units of Measurement2.1 In addition to being stated in i

25、nch/pound units, each numerical requirement in this standard is alsostated in units that make the requirement conveniently usable in the various metric systems (practical SIand customary). Equivalent although not necessarily exactly identical results are to be expected fromapplying a requirement in

26、inch/pound or metric terms. Equipment calibrated in metric units is to be usedwhen a requirement is applied in metric terms.3 References3.1 Whenever the designation “UL 1581” is used in this wire standard, reference is to be made to thedesignated part(s) of the Reference Standard for Electrical Wire

27、s, Cables, and Flexible Cords, UL 1581.4 Index Tables4.1 Tables 4.1 4.8 each serve as an index to the requirements for construction details, testperformance, and marking of the wire types described in the particular table. Each vertical columnsummarizes and references the requirements that apply to

28、the particular wire whose type letters appearat the top of the column. The applicable paragraphs and tables in this standard (UL 66) are indicated inparenthesis. Square brackets . indicate the applicable parts of UL 1581.JUNE 7, 2005 FIXTURE WIRE - UL 66 7UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR F

29、URTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULTable 4.1PTFE insulated Types PTF and PTFFaTable 4.1 revised July 16, 2003Type-letter designation PTF PTFFMaximum temperature 250C (482F) 150C (302F)Maximum voltage 600CONDUCTOR Sizes 18, 16, and 14 AWGMetal Nickel-base alloy or nickel-coa

30、tedcopper (6.1.2)Nickel-coated copper or silver-coated copper (6.1.2)Stranding Solid or 7-strand(6.1.1, 6.2.2, and 6.3.1)Flexible-stranded(6.1.1, 6.2.2, and 6.3.1)Size verification (6.4.1, 6.4.2, and 6.4.3) (6.4.1 and 6.4.3)Maximum length of lay ofstrands48 x individual strand diameter(6.3.2)(Table

31、6.2)General Continuity, joints, metal coating, and separator (6.5.1 7.3)INSULATION Material PTFE Table 50.219 of UL 1581 (8.1.1 8.1.4, 8.2.2.1, and 8.2.2.4)Minimum average thickness 20.0 mils or 0.51 mm (8.3.1)Minimum thickness at anypoint18.0 mils or 0.46 mm (Table 8.1)Covering over the insulation

32、No coveringTESTSONFINISHEDWIREPhysical properties tests ofinsulationPTFE Table 50.219 of UL 1581 (8.2.2.1 and 8.2.2.4)Continuity test of conductor (6.5.1, 11.1, and 11.2)D-C resistance test ofconductor(12.1 12.3)Spark test (13.1)Deformation test Not applicableCold bend test (15.1 15.7)Test for insul

33、ation resistanceat 60F(16.1 and 16.2)Flame tests for VW-1 wire(elective)(17.1)Vertical flame test (required) (18.1)Durability test of ink printing (20.1)MARKINGS Polarity ID (21.1)Legibility of printing (22.1)Sequence of printed markings No sequence is specified (23.1)Responsible organization andfac

34、tory IDs(24.1 24.3 and 24.5)Temperature ID (25.1 and 25.2)ID of VW-1 wire (27.1)Tag, reel, and cartonmarkings(28.1)Current designation Prohibited (29.1)Date of manufacture (30.1)aIndex tables are explained in 4.1.JULY 16, 2003FIXTURE WIRE - UL 668UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER RE

35、PRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULTable 4.2Polyimide tape insulated Types KF-1, KF-2, KFF-1, and KFF-2aTable 4.2 revised July 16, 2003Type-letter designation KF-1 KF-2 KFF-1 KFF-2Maximum temperature 200C (392F)Maximum voltage 300 600 300 600CONDUCTOR Sizes 18, 16, 14, 12, and 10 AW

36、GMetal Nickel-base alloy or nickel- or silver-coated copper (6.1.2)Stranding Solid or 7-strand(6.1.1, 6.2.2, and 6.3.1)Flexible-stranded(6.1.1, 6.2.2, and 6.3.1)Size verification (6.4.1, 6.4.2, and 6.4.3) (6.4.1 and 6.4.3)Maximum length oflay of strands48 x individual strand diameter (6.3.2) (Table

37、6.2)General Continuity, joints, metal coating, and separator (6.5.1 7.3)INSULATION Material Polyimide tapeMinimum averagethicknessKF-1 and KFF-1: 5.5 mils or 0.14 mmKF-2 and KFF-2: 8.4 mils or 0.21 mm (8.3.1)Minimum thicknessat any pointKF-1 and KFF-1: 5.0 mils or 0.13 mmKF-2 and KFF-2: 7.6 mils or

38、0.19 mm (Table 8.1)Covering over the insulation No coveringTESTS ONFINISHED WIREFlexing test ofinsulation afterconditioning(8.2.1.1 8.2.1.6)Continuity test ofconductor(6.5.1, 11.1, and 11.2)D-C resistance testof conductor(12.1 12.3)Spark test (13.1)Deformation test Not applicableCold bend test (15.1

39、 15.7)Test for insulationresistance at 60F(16.1 and 16.2)Flame tests forVW-1 wire(elective)(17.1)Vertical flame test(required)(18.1)Durability test of inkprinting(20.1)MARKINGS Polarity ID (21.1)Legibility of printing (22.1)Sequence ofprinted markingsNo sequence is specified (23.1)Responsibleorganiz

40、ation andfactory IDs(24.1 24.3 and 24.5)Temperature ID (25.1 and 25.2)ID of VW-1 wire (27.1)Tag, reel, andcarton markings(28.1)Current designation Prohibited (29.1)Date ofmanufacture(30.1)aIndex tables are explained in 4.1.JULY 16, 2003 FIXTURE WIRE - UL 66 9UL COPYRIGHTED MATERIAL NOT AUTHORIZED FO

41、R FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULTable 4.3FEP insulated Types PF, PGF, PFF, and PGFFaTable 4.3 revised July 16, 2003Type-letter designation PF PGF PFF PGFFMaximum temperature 200C (392F) 150C (302F)Maximum voltage 600CONDUCTOR Sizes 18, 16, and 14 AWGMetal Nickel-base

42、alloy or nickel- or silver-coated copper(6.1.2)Nickel-base alloy or uncoated or coatedcopper(6.1.1 and 6.1.2)Stranding Solid or 7-strand( 6.1.1, 6.2.2, and 6.3.1)Flexible-stranded(6.1.1, 6.2.2, and 6.3.1)Size verification (6.4.1, 6.4.2, and 6.4.3) (6.4.1 and 6.4.3)Maximum length oflay of strands48 x

43、 individual strand diameter (6.3.2) (Table 6.2)General Continuity, joints, metal coating, and separator (6.5.1 7.3)INSULATION Material FEP Table 50.73 of UL 1581 (8.1.1 8.1.4, 8.2.2.1, and 8.2.2.4)Minimum averagethicknessPF and PFF: 20.0 mils or 0.51 mm PGF and PGFF: 14.0 mils or 0.36 mm (8.3.1)Mini

44、mum thicknessat any pointPF and PFF: 18.0 mils or 0.46 mm PGF and PGFF: 12.6 mils or 0.32 mm (Table8.1)Covering over the insulation:Elective on Types PF and PFFRequired on Types PGF and PGFFSaturated glass or aramid-fiber braid (10.2.1, 10.2.2, and 10.2.4)Other covering (10.2.5)TESTS ONFINISHED WIRE

45、Physical propertiestests of insulationFEP Table 50.73 of UL 1581 (8.2.2.1 and 8.2.2.4)Conductorcorrosion test(uncoated copperonly)No test 500.1 of UL 1581 (6.7.1)Continuity test ofconductor(6.5.1, 11.1, and 11.2)D-C resistance testof conductor(12.1 12.3)Spark test (13.1)Deformation test (14.1 14.3)C

46、old bend test (15.1 15.7)Test for insulationresistance at 60F(16.1 and 16.2)Flame tests forVW-1 wire(elective)(17.1)Vertical flame test(required)(18.1)Flexing test ofcovering(10.2.4 and 10.2.5)Durability test of inkprintingNot applicableJULY 16, 2003FIXTURE WIRE - UL 6610Table 4.3 Continued on Next

47、PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULTable 4.3 ContinuedType-letter designation PF PGF PFF PGFFMARKINGS Polarity ID (21.2 and 21.3)Legibility of printing (22.1)Sequence ofprinted markingsNo sequence is specified (23.1)Responsibl

48、eorganization andfactory IDs(24.1, 24.3, and 24.4)Temperature ID (25.1 and 25.2)ID of VW-1 wire (27.1)Tag, reel, andcarton markings(28.1)Current designation Prohibited (29.1)Date ofmanufacture(30.1)aIndex tables are explained in 4.1.Table 4.4Silicone rubber insulated Types SF-1, SFF-1, SF-2, and SFF

49、-2aTable 4.4 revised June 7, 2005Type-letter designation SF-1 SF-2 SFF-1 SFF-2Maximum temperature 200C (392F) 150C (302F)Maximum voltage 300 600 300 600CONDUCTOR Sizes 18 AWG 18, 16, 14, 12, and10 AWG18 AWG 18, 16, 14, 12, and10 AWGMetal Nickel-base alloy or copper coated with tin, nickel, or silver(6.1.1 and 6.1.2)Stranding Solid or 7-strand(6.1.1, 6.2.2, and 6.3.1)Flexible-stranded(6.1.1, 6.2.2, and 6.3.1)Size verification (6.4.1 6.4.3) (6.4.1 and 6.4.3)Maximum length oflay of