UL 61800-5-1 (ND)-2012 National Differences For UL 61800-5-1 Adjustable Speed Electrical Power Drive Systems C Part 5-1 Safety Requirements C Electrical Thermal and Energy (First El.pdf

《UL 61800-5-1 (ND)-2012 National Differences For UL 61800-5-1 Adjustable Speed Electrical Power Drive Systems C Part 5-1 Safety Requirements C Electrical Thermal and Energy (First El.pdf》由会员分享，可在线阅读，更多相关《UL 61800-5-1 (ND)-2012 National Differences For UL 61800-5-1 Adjustable Speed Electrical Power Drive Systems C Part 5-1 Safety Requirements C Electrical Thermal and Energy (First El.pdf（112页珍藏版）》请在麦多课文档分享上搜索。

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULNational Differences ForUL 61800-5-1Standard for Adjustable Speed Electrical Power Drive Systems - Part 5-1: Safety Requirements -Electrical, Thermal and EnergyUL COPYRIGHTED MATERIAL NOT AUTHORI

2、ZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULNational Differences ForUL 61800-5-1Standard for Adjustable Speed Electrical Power Drive Systems - Part 5-1: Safety Requirements -Electrical, Thermal and EnergyEdition: 1Edition Date: June 8, 2012This revision was issued to incorp

3、orate the following changes:1. Clarification of Requirements for Functional Insulation2. Impulse Test and Partial Discharge Test for Solid Insulating Materials3. Generic Materials for Direct Support of Live Parts4. Generic Materials Used as Insulating Barriers in Lieu of SpacingsThis document provid

4、es a single listing of the National Differences included in the UL adoption ofthe corresponding IEC standard.All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, ortransmitted in any form by any means, electronic, mechanical photocopying, recording, or ot

5、herwisewithout prior permission of UL.UL provides this standards document as is without warranty of any kind, either expressed or implied,including but not limited to, the implied warranties of merchantability or fitness for any purpose.In no event will UL be liable for any special, incidental, cons

6、equential, indirect or similar damages,including loss of profits, lost savings, loss of data, or any other damages arising out of the use of or theinability to use this standards document, even if UL or an authorized UL representative has been advisedof the possibility of such damage. In no event sh

7、all ULs liability for any damage ever exceed the pricepaid for this standards document, regardless of the form of the claim.Users of the electronic versions of ULs Standards for Safety agree to defend, indemnify, and hold ULharmless from and against any loss, expense, liability, damage, claim, or ju

8、dgment (including reasonableattorneys fees) resulting from any error or deviation introduced while purchaser is storing an electronicStandard on the purchasers computer system.Copyright 2015 Underwriters Laboratories Inc.MARCH 6, 2015NATIONAL DIFFERENCES FOR UL UL 61800-5-12UL COPYRIGHTED MATERIAL N

9、OT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULPrefaceThis document provides a single listing of the technical National Differences included in the UL adoptionof the corresponding IEC standard.In its IEC-based standards, UL uses the notations indicated below to ident

10、ify national difference type, andthese types are additionally noted in this document. The standard may not use all types of thesedeviations.D1 - These are deviations which are based on basic safety principles and requirements, elimination ofwhich would compromise safety for U.S. consumers and users

11、of products.D2 - These are deviations based on safety practices. These are deviations for IEC requirements that maybe acceptable, but adopting the IEC requirements would require considerable retesting or redesign on themanufacturers part.DC - These are deviations based on the component standards and

12、 will not be deleted until a particularcomponent standard is harmonized with the IEC component standard.DE - These are deviations based on editorial comments or corrections.DR - These are deviations based on the national regulatory requirements.Each national difference contains a description of what

13、 the national difference entails. Typically one of thefollowing words is used to explain how the text of the national difference is to be applied to the base IECtext:Addition / Add - An addition entails adding a complete new numbered clause, subclause, table,figure, or annex. Addition is not meant t

14、o include adding select words to the base IEC text.Deletion / Delete - A deletion entails complete deletion of an entire numbered clause, subclause,table, figure, or annex without any replacement text.Modification / Modify - A modification is an altering of the existing base IEC text such as theaddi

15、tion, replacement or deletion of certain words or the replacement of an entire clause,subclause, table, figure, or annex of the base IEC text.MARCH 6, 2015 NATIONAL DIFFERENCES FOR UL UL 61800-5-1 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM

16、 ULNational Differences1DV.1 D2 Modification to add the following:DV.1.1 This document is only applicable to the power conversion and drive controlequipment, servo drives and integral servo drive/motor combinations.DV.1.2 Only devices connected to line voltages of up to 1,5 kV a.c. are covered.DV.1.

17、3 A component of a product covered by this standard shall comply with therequirements for that component. See Annex DVA for a list of additional standardscovering components used in the products covered by this standard.1DV.2 DR Modification to add the following:This equipment is for use in ordinary

18、 locations in accordance with Articles 430 and 440 ofthe National Electrical Code, NFPA 70.1DV.3 D2 Modification to add the following:Specifications provided in other parts of the 61800 Series of Standards (for example EMCin part 3) apply only on agreement between the manufacturer and the customer.2

19、DV D2 Modification to add the following:See Annex DVA for USA Normative References and Component Standards. See AnnexDVB for IEC Normative References that do not apply and for IEC Normative Referencesreplaced by USA Standards.Table 1DV DE Modification to add the following terms to Table 1:AMBIENT TE

20、MPERATURE 3.1ADVCONTROL CIRCUIT 3.6ADVGROUP INSTALLATION 3.12ADVINSULATED LIVE PART 3.14ADVSOLID STATE MOTOR OVERLOAD PROTECTION 3.36ADVSOLID STATE SHORT CIRCUIT PROTECTION 3.36BDVSURROUNDING AIR TEMPERATURE RATING 3.37ADVTHERMAL MEMORY 3.40DVTHERMAL MEMORY RETENTION 3.41DVTRIPPING CURRENT 3.40ADV3.

21、1ADV D2 Addition:AMBIENT TEMPERATURE: the temperature of the room or chamber in which the equipmentunder test is locatedMARCH 6, 2015NATIONAL DIFFERENCES FOR UL UL 61800-5-14UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM UL3.6ADV D2 Addition:CO

22、NTROL CIRCUIT: a circuit that carries the electric signals directing the performance of acontroller, and does not carry the main power circuit (see IEEE Standards Dictionary ofElectrical and Electronic Terms). A CONTROL CIRCUIT is mostly limited to 15 A.3.12ADV D2 Addition:GROUP INSTALLATION: A moto

23、r branch circuit for two or more motors, or one or more motorswith other loads and protected by a circuit breaker or a single set of fuses.3.13DV D2 Modification:Equipment operating at more than 600 Vac is considered high-voltage equipment withrespect to the requirements in the National Electrical C

24、ode.3.14ADV D2 Addition:INSULATED LIVE PART: An electrically LIVE PART that is provided with complete protectionagainst electric shock and does not rely upon other parts for insulation3.18DV D2 Modification:Equipment operating at more than 600 Vac is not considered low-voltage equipment withrespect

25、to the requirements in the National Electrical Code.3.36ADV D2 Addition:SOLID STATE MOTOR OVERLOAD PROTECTION: Circuitry integral to the power conversion equipmentthat acts to protect a motor under overload conditions by reducing current flow to themotor output terminals. This protection is typicall

26、y achieved through an algorithm basedon the I2t of the current to the motor. The protection circuitry is usually comprised ofhardware, firmware and software components.3.36BDV D2 Addition:SOLID STATE SHORT CIRCUIT PROTECTION: Circuitry integral to power conversion equipment thatacts to suspend curre

27、nt flow to the motor output terminals upon sensing a preset orpredetermined condition such as a rapid rate of change in output current or bus voltage.The protection circuitry may be comprised of hardware, firmware and softwarecomponents.3.37ADV D2 Addition:SURROUNDING AIR TEMPERATURE RATING: a ratin

28、g assigned to OPEN TYPE equipment that refers tothe maximum AMBIENT TEMPERATURE of air immediately surrounding the equipment inside ofthe ultimate enclosure3.40DV D2 Addition:THERMAL MEMORY: The ability of an overload protective system to approximate the heatingand cooling of a protected motor durin

29、g operation.MARCH 6, 2015 NATIONAL DIFFERENCES FOR UL UL 61800-5-1 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM UL3.40ADV D2 Addition:TRIPPING CURRENT: Current level greater than rated output motor current at which the motoroverload protecti

30、on circuitry will function. May be provided as a percent of motor currentor as an actual stated current value.3.41DV D2 Addition:THERMAL MEMORY RETENTION: The maintaining of the THERMAL MEMORY upon shutdown or powerloss. This includes retention of the last thermal value, and may include an ongoingre

31、duction of this thermal value to reflect the cooling of the motor. This information willbe used by the overload protective system to approximate the thermal state of the motorupon restart.4.1DV.1 DR Modification to add the following:Power conversion equipment shall be constructed so that it complies

32、 with the rules forINSTALLATION and use of such equipment as given in the National Electrical Code, ANSI/NFPA70.4.1DV.2 D2 Modification to add the following:4.1DV.2.1 Power conversion equipment shall employ materials that are evaluated for theuse.4.1DV.2.2 The acceptability of insulating materials i

33、s to be determined with respect toproperties such as flammability, arc-resistance, and similar properties, based on anoperating temperature equal to the measured temperature adjusted to the minimumanticipated end use ambient of 40C (104F), unless the equipment is marked inaccordance with 6.3.3 for a

34、 higher end use ambient.4.1DV.2.3 Iron and steel parts shall be protected against corrosion by enameling,galvanizing, plating, or other equivalent means. This applies to all springs and other partsupon which proper mechanical operation may depend other than the following items:1) Bearings, thermal e

35、lements, sliding surfaces of a hinge, or shaft, and the like,where such protection is impracticable;2) Small parts of iron or steel, such as washers, screws, bolts, and the like, thatare not current carrying, if the corrosion of such parts would not be likely toresult in a risk of fire, electric sho

36、ck, or injury to persons; and3) Parts made of stainless steel that are polished or treated.4.1DV.3 D2 Modification to add the following:For Isolated Secondary Circuits the requirements in Annex DVC can be used to determineif any of the requirements for risk of electric shock, thermal or energy hazar

37、ds may bewaived.MARCH 6, 2015NATIONAL DIFFERENCES FOR UL UL 61800-5-16UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM UL4.2DV.1 D2 Modification to add the following:4.2DV.1.1 Critical components4.2DV.1.1.1 The use of probability of failure for w

38、aiving circuit analysis on components isnot applicable. The circuit analysis shall be used to identify critical components withrespect to resulting thermal or electric shock hazard. Further analysis shall be used todetermine the components to be subjected to the test in 5.2.3.6.4.4.2DV.1.1.2 The bre

39、akdown of components testing is not required for:a) Components in Class 2 circuits as defined in Annex DVC;b) Components in limited voltage/current secondary circuits as defined in AnnexDVC;c) Components in limiting impedance circuits as defined in Annex DVC; andd) Components complying with the requ

40、irements applicable to the componentwhere those requirements address the failure mode under evaluation for thecircuit conditions in which the component is used within the drive.4.2DV.2 D2 Modification to add the following:4.2DV.2.1 Contactor overload4.2DV.2.1.1 A contactor in a power circuit shall b

41、e suitable for controlling the connectedload, including making, carrying and breaking the overload current that can be deliveredby the equipment. A contactor with lower ratings may be used when it is interlocked orsequenced such that in normal operation the contactor does not make or break loadcurre

42、nt and meets the requirements of 5.2.4.5.5DV.4.2DV.3 D2 Modification to add the following:4.2DV.3.1 Current limiting control4.2DV.3.1.1 Power conversion equipment incorporating a current limiting control is to betested in accordance with 5.2.4.5.6DV.4.3.3.1DV DC Modification:In the US, motor require

43、ments are provided in UL 2111 and the UL 1004 series ofstandards.4.3.3.3DV.1 D2 Modification:It is permitted to open enclosures or remove barriers without the use of a tool and withoutde-energization of LIVE PARTS of DVC A, B or C circuits.4.3.3.3DV.2 D2 Modification:Accessibility of LIVE PARTS of D

44、VC B or C circuits shall be determined in accordance withAnnex DVD.MARCH 6, 2015 NATIONAL DIFFERENCES FOR UL UL 61800-5-1 7UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM UL4.3.4.3DV D2 Modification:Impulse voltage testing is not required.4.3.5.

45、1DV D2 Modification:Protection by means of CLASS II methods are not applicable.4.3.5.3.1DV.1 D1 Modification:Item b) is not applicable.4.3.5.3.1DV.2 D2 Modification to add the following:4.3.5.3.1DV.2.1 Bonding4.3.5.3.1DV.2.1.1 Other than as noted in 4.3.5.3.1DV.2.1.2 and 4.3.5.3.1DV.2.1.3, anenclosu

46、re made of insulating material, either wholly or in part, shall have bonding meansto provide continuity of grounding between all conduit openings. The bonding means shallbe either completely assembled on the product or provided as separate parts for fieldINSTALLATION.4.3.5.3.1DV.2.1.2 A bonding mean

47、s required in 4.3.5.3.1DV.2.1.1 is not required for anenclosure that is intended to be connected to a single conduit. Enclosures shall be markedin accordance with 6.3.6.6DV.3.4.3.5.3.1DV.2.1.3 A bonding means required in 4.3.5.3.1DV.2.1.1 is not required to beprovided with each enclosure when such m

48、eans is available in the form of a kit from themanufacturer and the equipment complies with the marking requirements in 6.3.6.6DV.2.4.3.5.3.1DV.2.1.4 Other than as noted in 4.3.5.3.1DV.2.1.5, the continuity of a conduitsystem shall be provided by metal-to-metal contact not relying on a polymeric mat

49、erial.4.3.5.3.1DV.2.1.5 The continuity of the grounding system is not prohibited from relying onthe integrity of the polymeric enclosure when samples have been subjected to the creeptest requirements in the Standard for Polymeric Materials Use in Electrical EquipmentEvaluations, UL 746C. Overcurrent Tests shall be conducted at 200 percent of the ratedcurrent of the branch circuit-protective device.4.3.5.3.1DV.2.1.6 A separate bonding conductor whether in a plastic or metal enclosureshall be copper, a copper alloy, or other material determined to be usable as an electricalc