UL 47-2004 UL Standard for Safety Semiautomatic Fire Hose Storage Devices (Sixth Edition Reprint with Revisions Through and Including May 25 2017)《安全半自动消防软管存储装置用UL标准 第6版》.pdf

《UL 47-2004 UL Standard for Safety Semiautomatic Fire Hose Storage Devices (Sixth Edition Reprint with Revisions Through and Including May 25 2017)《安全半自动消防软管存储装置用UL标准 第6版》.pdf》由会员分享，可在线阅读，更多相关《UL 47-2004 UL Standard for Safety Semiautomatic Fire Hose Storage Devices (Sixth Edition Reprint with Revisions Through and Including May 25 2017)《安全半自动消防软管存储装置用UL标准 第6版》.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 47 Semiautomatic Fire Hose Storage DevicesUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR

2、 FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Semiautomatic Fire Hose Storage Devices, UL 47 Sixth Edition, Dated April 27, 2004 Summary of Topics This revision of ANSI/UL 47 is being issued to reect the reaffirmation of ANSI approval. No changes in requ

3、irements have been made. Text that has been changed in any manner or impacted by ULs electronic publishing system is marked with a vertical line in the margin. Changes in requirements are marked with a vertical line in the margin and are followed by an effective date note indicating the date of publ

4、ication or the date on which the changed requirement becomes effective. The revisions dated December 18, 2012 include a reprinted title page (page 1) for this standard. The requirements are substantially in accordance with Proposal(s) on this subject dated October 26, 2012. All rights reserved. No p

5、art of this publication may be reproduced, stored in a retrieval system, or transmitted in any form by any means, electronic, mechanical photocopying, recording, or otherwise without prior permission of UL. UL provides this Standard as is without warranty of any kind, either expressed or implied, in

6、cluding but not limited to, the implied warranties of merchantability or tness for any purpose. In no event will UL be liable for any special, incidental, consequential, indirect or similar damages, including loss of prots, lost savings, loss of data, or any other damages arising out of the use of o

7、r the inability to use this Standard, even if UL or an authorized UL representative has been advised of the possibility of such damage. In no event shall ULs liability for any damage ever exceed the price paid for this Standard, regardless of the form of the claim. Users of the electronic versions o

8、f ULs Standards for Safety agree to defend, indemnify, and hold UL harmless from and against any loss, expense, liability, damage, claim, or judgment (including reasonable attorneys fees) resulting from any error or deviation introduced while purchaser is storing an electronic Standard on the purcha

9、sers computer system. The requirements in this Standard are now in effect, except for those paragraphs, sections, tables, gures, and/or other elements of the Standard having future effective dates as indicated in the note following the affected item. The prior text for requirements that have been re

10、vised and that have a future effective date are located after the Standard, and are preceded by a SUPERSEDED REQUIREMENTS notice. DECEMBER 18, 2012 UL 47 tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL DECEMBER 18, 2012 UL 47 tr2 No Text

11、on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL April 27, 2004 (Title Page Reprinted: December 18, 2012) 1 UL 47 Standard for Semiautomatic Fire Hose Storage Devices First Edition January, 1972 Second Edition April, 1979 Third Ed

12、ition July, 1980 Fourth Edition May, 1987 Fifth Edition September, 1993 Sixth Edition April 27, 2004 This ANSI/UL Standard for Safety consists of the Sixth edition, including revisions through December 18, 2012. The most recent designation of ANSI/UL 47 as a Reaffirmed American National Standard (AN

13、S) occurred on December 18, 2012. ANSI approval for a standard does not include the Cover Page, Transmittal Pages, Title Page, or effective date information. Comments or proposals for revisions on any part of the Standard may be submitted to UL at any time. Proposals should be submitted via a Propos

14、al Request in ULs On-Line Collaborative Standards Development System (CSDS) at http:/. ULs Standards for Safety are copyrighted by UL. Neither a printed nor electronic copy of a Standard should be altered in any way. All of ULs Standards and all copyrights, ownerships, and rights regarding those Sta

15、ndards shall remain the sole and exclusive property of UL. COPYRIGHT 2012 UNDERWRITERS LABORATORIES INC. ANSI/UL 47-2004 (R2012)UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL APRIL 27, 2004 SEMIAUTOMATIC FIRE HOSE STORAGE DEVICES - UL 47 2

16、No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONTENTS INTRODUCTION 1 Scope .4 2 Components 4 3 Units of Measurement .5 4 Undated References 5 5 Glossary .5 CONSTRUCTION 6 General 5 7 Assembly 6 8 Materials .6 9 Threads

17、 6 10 Pipe 6 11 Rack and Reel-Type Storage Device .7 12 Cabinet Type Storage Device .8 13 Fire Hose .9 PERFORMANCE 14 General .9 15 Installation Test 9 16 Operational Tests 9 16.1 Samples .9 16.2 Water retention test 9 16.3 Run-off and release test .10 16.4 Secureness test 10 16.5 Rough usage test 1

18、0 17 Accelerated Air-Oven Aging Test .10 PACKING FOR SHIPMENT 18 General 11 MANUFACTURING AND PRODUCTION TESTS 19 General 11 MARKING 20 General 11 APPENDIX A Standards for ComponentsA1 APRIL 27, 2004 SEMIAUTOMATIC FIRE HOSE STORAGE DEVICES - UL 47 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER

19、REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL INTRODUCTION 1 Scope 1.1 These requirements cover semiautomatic re hose storage devices (SHSD) intended for use in controlling incipient res by occupants of buildings. An SHSD is intended for use with specically-identied re hose. 1.2 Requiremen

20、ts for the installation, use, and care of hose storage devices and re hose are included in the following standards of the National Fire Protection Association: Installation of Standpipe, Private Hydrants, and Hose Systems, NFPA 14; and Care, Use, and Service Testing of Fire Hose, Including Connectio

21、ns and Nozzles, NFPA 1962. 1.3 Semiautomatic re hose storage devices as covered by these requirements use hose having an inside diameter of 1-1/2 inches (38.1 mm) or less and are capable of storing not more than 100 feet (30 m) of re hose, in accordance with the Standard for Installation of Standpip

22、e and Hose Systems, NFPA 14. 2 Components 2.1 Except as indicated in 2.2, a component of a product covered by this standard shall comply with the requirements for that component. See Appendix A for a list of standards covering components generally used in the products covered by this standard. 2.2 A

23、 component is not required to comply with a specic requirement that: a) Involves a feature or characteristic not required in the application of the component in the product covered by this standard, or b) Is superseded by a requirement in this standard. 2.3 A component shall be used in accordance wi

24、th its rating established for the intended conditions of use. 2.4 Specic components are incomplete in construction features or restricted in performance capabilities. Such components are intended for use only under limited conditions, such as certain temperatures not exceeding specied limits, and sh

25、all be used only under those specic conditions. APRIL 27, 2004 SEMIAUTOMATIC FIRE HOSE STORAGE DEVICES - UL 47 4UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 3 Units of Measurement 3.1 Values stated without parentheses are the requirement.

26、 Values in parentheses are explanatory or approximate information. 4 Undated References 4.1 Any undated reference to a code or standard appearing in the requirements of this standard shall be interpreted as referring to the latest edition of that code or standard. 5 Glossary 5.1 For the purpose of t

27、his standard the following denitions apply. 5.2 FULL FLOW CONDITIONS The ow rate at the rated service pressure with the nozzle in a fully- open position and the re hose fully extended. 5.3 SERVICE PRESSURE The static outlet pressure in pounds per square inch available at the standpipe to which the r

28、e hose storage device is to be connected. 5.4 SHSD Semiautomatic re hose storage device. 5.5 WORKING PRESSURE The owing pressure in pounds per square inch available at the nozzle end of the re hose. CONSTRUCTION 6 General 6.1 An SHSD shall: a) Incorporate mounting means to mount the SHSD securely to

29、 a building structure or standpipe; and b) Provide access to the operator of the hose valve and to the SHSD. 6.2 An SHSD shall operate as intended at a maximum service pressure of 150 or 175 psi (1034 or 1206 kPa). 6.3 An SHSD shall withstand rough usage without its strength being reduced or its ope

30、ration being affected. See Operational Tests, Section 16. APRIL 27, 2004 SEMIAUTOMATIC FIRE HOSE STORAGE DEVICES - UL 47 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 7 Assembly 7.1 An SHSD shall consist of a hose rack, hose reel, or hose

31、 cabinet and the necessary interconnecting piping for the re hose with which the SHSD is intended to be used. The re hose with which the SHSD is intended to be used may or may not be provided with the SHSD. If the SHSD is not provided with the re hose, the SHSD shall be marked as specied in 20.1(e).

32、 7.2 The nish, assembly, and placement of the components of an SHSD shall be such that the re hose is not subjected to chang on rough or sharp edges during storage or usage of the assembly. 7.3 An SHSD shall be provided with means to hold the hose nozzle when not in use. The nozzle shall be held sec

33、urely, but still be able to be readily disengaged for use. See 16.4.1. 7.4 An SHSD shall be provided with a device to retain the water within the rst three loops of the re hose at the standpipe end when the inlet to the hose is subjected to water at the rated service pressure. See 11.1(d) and 16.2.

34、7.5 Unless the operation of the water retaining device is automatic, an SHSD shall be provided with means to indicate that the water retaining device is engaged after the re hose is installed. 8 Materials 8.1 The materials used in the construction of those parts of an SHSD that remain in stress afte

35、r assembly shall not be subject to stress corrosion. 9 Threads 9.1 The inlet provided for eld installation of an SHSD shall be threaded or tapped with taper threads in accordance with the Standard for Pipe Threads, General Purpose (Inch), ANSI/ASME B1.20.1. 10 Pipe 10.1 The external surfaces of pipe

36、 ends, if provided for the attachment of an SHSD to a standpipe system, shall include a surface to which a wrench may be tted without damaging the threads of the pipe ends. APRIL 27, 2004 SEMIAUTOMATIC FIRE HOSE STORAGE DEVICES - UL 47 6UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION

37、 OR DISTRIBUTION WITHOUT PERMISSION FROM UL 11 Rack and Reel-Type Storage Device 11.1 A rack or reel for storage of a re hose shall be constructed so that: a) The re hose is unlikely to be placed on the rack or reel in such manner as to make its removal difficult; b) The re hose can be quickly and u

38、niformly pulled off at the nozzle end; c) The entire specied length of re hose can be stored on the rack or reel; d) After opening the hose valve, the re hose will remain in position on the rack or reel until the re hose has been manually pulled off to its full length; e) The rack or reel, with the

39、specied length of re hose installed, will permit removal of the re hose through any point of an arc of 180 degrees; f) There are no projections to catch the re hose or otherwise interfere with the rapid removal of the hose; and g) Repairs to the rack or reel, or its components, can be made readily a

40、nd without using special tools. 11.2 The material of all parts in which freedom of movement is essential shall be of brass, bronze, stainless steel, or coated ferrous metal, or an equally corrosion-resistant material. 11.3 Any metallic nish, when subjected to comparative tests, shall provide corrosi

41、on protection equivalent to brass, bronze, or stainless steel. 11.4 The rack or reel mechanism shall not include components necessary for its intended use that are loose or that may be lost or misplaced. 11.5 The re hose, when installed in the rack or reel, shall lie or hang in natural folds or be c

42、oiled on a spool. APRIL 27, 2004 SEMIAUTOMATIC FIRE HOSE STORAGE DEVICES - UL 47 7UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 12 Cabinet Type Storage Device 12.1 A cabinet-type SHSD shall be sized to permit full and ready access to all o

43、perating components of the device, shall not interfere with the prompt and efficient handling of the hose, and shall allow the re hose to be pulled off its rack through an arc of 90 degrees. 12.2 A cabinet may be for surface, semirecessed, or full recessed installation to building walls. The mountin

44、g and support of the cabinet shall be independent of the re hose rack or piping connection to the standpipe. 12.3 A cabinet type SHSD shall be provided with a device to retain the water within the rst three loops of the re hose at the standpipe end when the inlet to the hose is subjected to water at

45、 the rated service pressure. 12.4 All surfaces and components of a cabinet and cabinet door shall be free of rough and sharp edges. 12.5 If provided, a cabinet door shall be hinged vertically and shall open to a 180 degree position relative to the cabinet front. 12.6 A cabinet door shall be provided

46、 with means to retain it in a closed position, but the means shall allow the door to be opened readily without the use of special tools. 12.7 A cabinet door shall not be secured with any type of locking device. 12.8 If a break glass type protective cover for a latching device is provided, the maximu

47、m area of the glass panel shall not exceed 25 square inches (161 cm 2 ). The device provided to break the glass panel shall be attached in the immediate area of the break glass panel and shall be arranged so that the device cannot be used to break other glass panels in the cabinet door. 12.9 A glass

48、 panel used in a cabinet door shall be made of glazing material complying with Safety Performance Specications and Methods of Test for Safety Glazing Material Used in Buildings, ANSI Z97.1. 12.10 The means provided to open a cabinet door shall be large enough to avoid entrapment or jamming of ngers.

49、 APRIL 27, 2004 SEMIAUTOMATIC FIRE HOSE STORAGE DEVICES - UL 47 8UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 13 Fire Hose 13.1 A re hose intended for use with an SHSD shall comply with the requirements of the Standard for Lined Fire Hose for Interior Standpipes, UL 219, or the Standard for Lined Fire Hose and Hose Assemblies, UL 19. PERFORMANCE 14 General 14.1 When an SHSD is tested in accordance