UL 17-2008 UL Standard for Safety Vent or Chimney Connector Dampers for Oil-Fired Appliances (Fourth Edition Reprint with Revisions through and Including September 25 2013)《燃油器具用通风.pdf

《UL 17-2008 UL Standard for Safety Vent or Chimney Connector Dampers for Oil-Fired Appliances (Fourth Edition Reprint with Revisions through and Including September 25 2013)《燃油器具用通风.pdf》由会员分享，可在线阅读，更多相关《UL 17-2008 UL Standard for Safety Vent or Chimney Connector Dampers for Oil-Fired Appliances (Fourth Edition Reprint with Revisions through and Including September 25 2013)《燃油器具用通风.pdf（58页珍藏版）》请在麦多课文档分享上搜索。

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 17 Vent or Chimney Connector Dampers for Oil-Fired AppliancesUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRIGHTED MATERIAL

2、 NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Vent or Chimney Connector Dampers for Oil-Fired Appliances, UL 17 Fourth Edition, Dated April 30, 2008 Summary of Topics This revision to UL 17 is being issued to remove the reference to th

3、e withdrawal date of UL 873 and to address universal upkeep of UL Standards for Safety. These revisions are considered to be non-substantive and not subject to ULs STP process. Text that has been changed in any manner or impacted by ULs electronic publishing system is marked with a vertical line in

4、the margin. Changes in requirements are marked with a vertical line in the margin and are followed by an effective date note indicating the date of publication or the date on which the changed requirement becomes effective. All rights reserved. No part of this publication may be reproduced, stored i

5、n a retrieval system, or transmitted in any form by any means, electronic, mechanical photocopying, recording, or otherwise without prior permission of UL. UL provides this Standard as is without warranty of any kind, either expressed or implied, including but not limited to, the implied warranties

6、of merchantability or tness for any purpose. In no event will UL be liable for any special, incidental, consequential, indirect or similar damages, including loss of prots, lost savings, loss of data, or any other damages arising out of the use of or the inability to use this Standard, even if UL or

7、 an authorized UL representative has been advised of the possibility of such damage. In no event shall ULs liability for any damage ever exceed the price paid for this Standard, regardless of the form of the claim. Users of the electronic versions of ULs Standards for Safety agree to defend, indemni

8、fy, and hold UL harmless from and against any loss, expense, liability, damage, claim, or judgment (including reasonable attorneys fees) resulting from any error or deviation introduced while purchaser is storing an electronic Standard on the purchasers computer system. The requirements in this Stan

9、dard are now in effect, except for those paragraphs, sections, tables, gures, and/or other elements of the Standard having future effective dates as indicated in the note following the affected item. The prior text for requirements that have been revised and that have a future effective date are loc

10、ated after the Standard, and are preceded by a SUPERSEDED REQUIREMENTS notice. SEPTEMBER 25, 2013 UL 17 tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL SEPTEMBER 25, 2013 UL 17 tr2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZE

11、D FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL APRIL 30, 2008 (Title Page Reprinted: September 25, 2013) 1 UL 17 Standard for Vent or Chimney Connector Dampers for Oil-Fired Appliances First Edition July, 1982 Second Edition November, 1988 Third Edition May, 1994 Fourth Editio

12、n April 30, 2008 This UL Standard for Safety consists of the Fourth Edition including revisions through September 25, 2013. Comments or proposals for revisions on any part of the Standard may be submitted to UL at any time. Proposals should be submitted via a Proposal Request in ULs On-Line Collabor

13、ative Standards Development System (CSDS) at http:/. ULs Standards for Safety are copyrighted by UL. Neither a printed nor electronic copy of a Standard should be altered in any way. All of ULs Standards and all copyrights, ownerships, and rights regarding those Standards shall remain the sole and e

14、xclusive property of UL. COPYRIGHT 2013 UNDERWRITERS LABORATORIES INC.UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL APRIL 30, 2008 VENT OR CHIMNEY CONNECTOR DAMPERS FOR OIL-FIRED APPLIANCES - UL 17 2 No Text on This PageUL COPYRIGHTED MATE

15、RIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONTENTS INTRODUCTION 1 Scope .5 2 Glossary .5 3 Components 6 4 Units of Measurement .7 CONSTRUCTION 5 Assembly 7 5.1 General .7 5.2 Electrical circuits .9 6 Materials .9 7 Springs 9 8 Enclosure 9 8.1 General .9

16、8.2 Doors and covers .12 8.3 Openings .13 9 Supply Connections 17 9.1 General 17 9.2 Lead wires 17 9.3 Terminals .18 9.4 Wiring space 19 10 Current-Carrying Parts 19 11 Mounting of Electrical Components .19 12 Internal Wiring 20 13 Separation of Circuits .21 14 Bonding for Grounding 22 15 Motors and

17、 Motor Overload Protection 24 16 Insulating Material 26 17 Spacings 26 17.1 General .26 17.2 High-voltage circuits 26 17.3 Low-voltage circuits .29 PERFORMANCE 18 General 29 19 Input 30 20 Heating Test .30 20.1 Test installation 30 20.2 Temperature measurements on other than electrical parts .33 20.

18、3 Temperature measurement on electrical components, thermocouple method 36 20.4 Test method .37 20.5 Assembly intended for installation in ue pipe system .40 20.6 Remote control assembly .40 21 Special Heating Test 40 22 Increased and Undervoltage Tests 41 23 Overload Test 41 24 Endurance Test 44 AP

19、RIL 30, 2008 VENT OR CHIMNEY CONNECTOR DAMPERS FOR OIL-FIRED APPLIANCES - UL 17 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 25 Dielectric Voltage-Withstand Test .44 26 Volt-Ampere Capacity Test .45 27 Burnout Test .46 28 10-Day Moist Am

20、monia Air Stress Cracking Test .46 29 Permanence of Marking .47 MANUFACTURING AND PRODUCTION TESTS 30 Dielectric Voltage-Withstand Test .47 31 Interlock Test .48 RATING 32 Details .48 MARKING 33 Details .49 INSTRUCTIONS 34 Installation Instructions 51 APPENDIX A Standards for ComponentsA1 APRIL 30,

21、2008 VENT OR CHIMNEY CONNECTOR DAMPERS FOR OIL-FIRED APPLIANCES - UL 17 4UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL INTRODUCTION 1 Scope 1.1 These requirements cover electrically operated damper assemblies, that are intended for install

22、ation in the vent or chimney connector of automatically operated oil-red appliances employing an atomizing type oil burner. The damper assembly is intended to restrict or block the connector opening when the burner is not ring. 1.2 These requirements cover automatic vent or chimney connector dampers

23、 for oil-red appliances having a ue gas temperature not in excess of 538C (1000F), unless marked for a lower temperature. See 5.1.1, 20.5.1, and 33.1(d). 1.3 The vent or chimney connector dampers covered under these requirements are not for use on oil-red appliances that employ vaporizing type oil b

24、urners. 1.4 Automatic vent or chimney connector dampers are intended for installation in accordance with the following standards of the National Fire Protection Association: a) Oil-Burning Equipment, NFPA 31. b) Chimneys, Fireplaces, and Vents, NFPA 211. c) National Electrical Code, ANSI/NFPA 70. 1.

25、5 A product that contains features, characteristics, components, materials, or systems new or different from those covered by the requirements in this standard, and that involves a risk of re or of electric shock or injury to persons shall be evaluated using appropriate additional component and end-

26、product requirements to maintain the level of safety as originally anticipated by the intent of this standard. A product whose features, characteristics, components, materials, or systems conict with specic requirements or provisions of this standard does not comply with this standard. Revision of r

27、equirements shall be proposed and adopted in conformance with the methods employed for development, revision, and implementation of this standard. 2 Glossary 2.1 For the purpose of this standard, the following denitions apply. 2.2 CHIMNEY CONNECTOR The conduit that connects a heating appliance with

28、a vertical ue. 2.3 COMBUSTIBLE MATERIAL, COMBUSTION PRODUCTS, NONCOMBUSTIBLE MATERIALS These terms, as used in this standard, are dened in the Standard Glossary of Terms Relating to Chimneys, Vents, and Heat-Producing Appliances, ANSI/NFPA 97M-1988. 2.4 DIRECT VENT SYSTEM APPLIANCE (Also called seal

29、ed combustion system appliance. )A self-contained appliance that by its inherent design, is constructed so that all air supplied for combustion, the combustion system of the appliance, and all products of combustion are completely isolated from the atmosphere of the space in which it is installed. 2

30、.5 DRAFT REGULATOR A device that functions to maintain a desired draft in an oil-red appliance by automatically reducing the chimney draft to the desired value. 2.6 ELECTRICAL CIRCUITS: APRIL 30, 2008 VENT OR CHIMNEY CONNECTOR DAMPERS FOR OIL-FIRED APPLIANCES - UL 17 5UL COPYRIGHTED MATERIAL NOT AUT

31、HORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL a) High-Voltage Circuit A circuit involving a potential of not more than 600 volts and having circuit characteristics in excess of those of a low-voltage or an isolated limited secondary circuit. b) Low-Voltage Circuit A cir

32、cuit involving a potential of not more than 30 volts ac (42.4 volts peak or dc) and supplied by a primary battery or by a standard Class 2 transformer, or by a combination of transformer and xed impedance that, as a unit, complies with all the performance requirements for a Class 2 transformer. (A c

33、ircuit derived from a source of supply classied as a high-voltage circuit, using resistance in series with the supply circuit as a means of limiting the voltage and current, is not considered to be a low-voltage nor an isolated limited secondary circuit.) c) Safety Control Circuit A circuit involvin

34、g one or more safety controls that open the circuit in the event of grounding, opening, or shorting of any part of the circuit. d) Isolated Limited Secondary Circuit A circuit of limited energy derived from an isolated secondary winding of a transformer having a maximum capacity of 100 volt-amperes

35、and open- circuit secondary voltage not exceeding 1000 volts. 2.7 SEALED COMBUSTION SYSTEM APPLIANCE See direct vent system appliance, 2.4. 2.8 VENT CONNECTOR The conduit that connects a heating appliance to a vertical vent. 3 Components 3.1 Except as indicated in 3.2, a component of a product cover

36、ed by this standard shall comply with the requirements for that component. See Appendix A for a list of standards covering components generally used in the products covered by this standard. 3.2 A component is not required to comply with a specic requirement that: a) Involves a feature or characteri

37、stic not required in the application of the component in the product covered by this standard, or b) Is superseded by a requirement in this standard. 3.3 A component shall be used in accordance with its rating established for the intended conditions of use. 3.4 Specic components are incomplete in co

38、nstruction features or restricted in performance capabilities. Such components are intended for use only under limited conditions, such as certain temperatures not exceeding specied limits, and shall be used only under those specic conditions. APRIL 30, 2008 VENT OR CHIMNEY CONNECTOR DAMPERS FOR OIL

39、-FIRED APPLIANCES - UL 17 6UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 4 Units of Measurement 4.1 Values stated without parentheses are the requirement. Values in parentheses are explanatory or approximate information. CONSTRUCTION 5 Ass

40、embly 5.1 General 5.1.1 A vent or chimney connector damper shall be constructed and assembled so that it will: a) Withstand a ue gas temperature of at least 538C (1000F), and b) Have the strength and rigidity necessary to resist the abuses to which it may be subjected, without total or partial colla

41、pse or without reduction of spacings, loosening or displacement of parts, or other serious defects, when it is tested in accordance with the requirements of this standard. Exception: A vent or chimney connector damper may be intended for a ue gas temperature less than 538C but not less than 399C (75

42、0F) provided the assembly is marked in accordance with 33.1(d). 5.1.2 A joint in metal surfaces of a ue gas passageway shall be tight, as attained by being welded, lock-seamed, riveted, or bolted. 5.1.3 If a vent or chimney connector damper consists of two or more subassemblies that are to be joined

43、 in the application to form one assembly, each subassembly shall be constructed for ready attachment of one to the other without requiring alteration, drilling, welding or cutting or a similar task by the installer. The securement of subassemblies to each other shall be by use of conventional means

44、such as screws or bolts and such securement means shall be provided as part of the subassemblies. 5.1.4 With respect to 5.1.3, the subassemblies that must bear a denite relationship to each other in order to operate as intended shall be arranged and constructed so as to permit them to be assembled o

45、nly in the correct relationship with each other. 5.1.5 All operating parts of a vent or chimney connector assembly shall be secured against displacement and shall be constructed so as to maintain a xed relationship between the parts under intended conditions of operation and handling. 5.1.6 The cons

46、truction of the vent or chimney connector damper shall be such that it permits, after burner shutdown, the escape of the products of combustion and hot gases that may be present in the combustion chamber of the appliance. The means provided for this purpose shall comply with the requirements in 5.1.

47、7. APRIL 30, 2008 VENT OR CHIMNEY CONNECTOR DAMPERS FOR OIL-FIRED APPLIANCES - UL 17 7UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 5.1.7 To comply with the requirement in 5.1.6, the vent or chimney connector damper shall include a time-de

48、lay feature that delays the closing of the damper blade so that it does not attain a fully closed position until a minimum of 3 minutes after the burner shutdown. Exception No. 1: Less than 3 minutes time-delay may be provided if the vent or chimney connector damper assembly is tested as described i

49、n 21.1 21.3. Exception No. 2: No time-delay is required if the damper blade provides, in the fully closed position, some free venting area and the vent or chimney connector damper assembly is tested as described in 21.1 21.3. 5.1.8 A vent or chimney connector damper assembly shall interlock electrically with the oil burner primary safety control so that the burner can be red only if the damper blade is in a fully open position. 5.1.9 A vent or chimney connector damper