UL 1662-1994 UL Standard for Safety Electric Chain Saws (Second Edition Reprint with Revisions Through and Including October 28 2009)《电动链锯》.pdf

《UL 1662-1994 UL Standard for Safety Electric Chain Saws (Second Edition Reprint with Revisions Through and Including October 28 2009)《电动链锯》.pdf》由会员分享，可在线阅读，更多相关《UL 1662-1994 UL Standard for Safety Electric Chain Saws (Second Edition Reprint with Revisions Through and Including October 28 2009)《电动链锯》.pdf（144页珍藏版）》请在麦多课文档分享上搜索。

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULUL 1662Electric Chain SawsUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION

2、ORDISTRIBUTION WITHOUT PERMISSION FROM ULUL Standard for Safety for Electric Chain Saws, UL 1662Second Edition, Dated October 14, 1994Summary of TopicsThese revisions to UL 1662 are being issued to address universal upkeep of UL Standards forSafety. These revisions are considered to be non-substanti

3、ve and not subject to ULs STPprocess.Text that has been changed in any manner or impacted by ULs electronic publishing system is markedwith a vertical line in the margin. Changes in requirements are marked with a vertical line in the marginand are followed by an effective date note indicating the da

4、te of publication or the date on which thechanged requirement becomes effective.All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, ortransmitted in any form by any means, electronic, mechanical photocopying, recording, or otherwisewithout prior permissi

5、on of UL.UL provides this Standard as is without warranty of any kind, either expressed or implied, including butnot limited to, the implied warranties of merchantability or fitness for any purpose.In no event will UL be liable for any special, incidental, consequential, indirect or similar damages,

6、including loss of profits, lost savings, loss of data, or any other damages arising out of the use of or theinability to use this Standard, even if UL or an authorized UL representative has been advised of thepossibility of such damage. In no event shall ULs liability for any damage ever exceed the

7、price paid forthis Standard, regardless of the form of the claim.Users of the electronic versions of ULs Standards for Safety agree to defend, indemnify, and hold ULharmless from and against any loss, expense, liability, damage, claim, or judgment (including reasonableattorneys fees) resulting from

8、any error or deviation introduced while purchaser is storing an electronicStandard on the purchasers computer system.The requirements in this Standard are now in effect, except for those paragraphs, sections, tables, figures,and/or other elements of the Standard having future effective dates as indi

9、cated in the note following theaffected item. The prior text for requirements that have been revised and that have a future effective dateare located after the Standard, and are preceded by a SUPERSEDED REQUIREMENTS notice.OCTOBER 28, 2009 UL 1662 tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHE

10、R REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULOCTOBER 28, 2009 UL 1662tr2No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULOCTOBER 14, 1994(Title Page Reprinted: October 28, 2009)1UL 1662Standard for Electric Chain

11、SawsFirst Edition August, 1986Second EditionOctober 14, 1994Comments or proposals for revisions on any part of the Standard may besubmitted to UL at any time. Proposals should be submitted via a ProposalRequest in ULs On-Line Collaborative Standards Development System (CSDS)at http:/.ULs Standards f

12、or Safety are copyrighted by UL. Neither a printed nor electroniccopy of a Standard should be altered in any way. All of ULs Standards and allcopyrights, ownerships, and rights regarding those Standards shall remain thesole and exclusive property of UL.COPYRIGHT 2009 UNDERWRITERS LABORATORIES INC.UL

13、 COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULMARCH 31, 2006ELECTRIC CHAIN SAWS - UL 16622No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULCONTENTSPART 1 ALL CHAIN SAW

14、SINTRODUCTION1 Scope .72 Glossary .73 Components 84 Units of Measurement .8CONSTRUCTION5 General 86 Frame and Enclosure 86A Accessibility Of Live Parts .107 Mechanical Assembly .10D8 Protection Against Corrosion 119 Power-Supply Cords .119.1 Cords and plugs .119.2 Strain relief .129.3 Bushings 12A10

15、 Live Parts 1311 Internal Wiring 1312 Insulating Material 1513 Motors .1614 Switches and Controls .1615 Thermal Cutoffs 1616 Capacitors .1617 Spacings 1718 Grounding .1819 Insulating Surfaces 18PROTECTION AGAINST INJURY TO PERSONS20 General 1921 Accessories and Attachments 1922 Materials .2023 Enclo

16、sures and Guards 2024 Switches and Controls .2125 Handles .2126 Construction 24A27 Guide Bar 2528 Carrying Case 2529 Chain Brake or Hand Guard .2530 Kickback .26MARCH 31, 2006 ELECTRIC CHAIN SAWS - UL 1662 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMIS

17、SION FROM ULPERFORMANCE31 General 26A32 Leakage Current Test .2733 Starting Current Test .28A34 Current Input Test 2935 Temperature Test .2936 Dielectric Voltage-Withstand Test .3237 Leakage Current Following Humidity Test 3338 Dew Point Test .3439 Continuity of Grounding Connection Test 3440 Strain

18、 Relief Test .3440A Push-Back Relief Test 34A41 Cord Flexing Test .34A42 Pressure Pad Test 3643 Switch or Control Overload Test 3644 Electronic Components Test .3745 Burnout Test .3746 Resistance to Impact Test .3846.1 Brush cap .3846.2 Grounded chain saw 3846.3 Insulated handle .3946.4 Injury to pe

19、rsons .3947 Static Load Test .40A48 Sound Level Test .4249 Chain Brake System Test 4449A Attachment Plug Test 44POLYMERIC ENCLOSURES50 General 44B51 Polymeric Materials as Described in 51.1.1 51.5.9 4551.1 Oven conditioning test 4551.2 Mold-stress evaluation test 4651.3 Resistance to impact test 465

20、1.4 Abnormal operation test .4651.5 Flame resistance test .4752 Polymeric Materials as Described in 52.1.1 52.8.3 4852.1 General .4852.2 Flame spread test 4852.3 Resistance to hot-wire ignition test .4852.4 Volume resistivity test .4952.5 Spacings to enclosure 4952.6 Overload 5052.7 Impact test 5052

21、.8 Oven conditioning test 50TESTS BY THE MANUFACTURER53 Dielectric Voltage-Withstand Test .5154 Grounding Continuity Test .53MARCH 31, 2006ELECTRIC CHAIN SAWS - UL 16624UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULRATING55 Details .53MARKIN

22、G56 Details .5457 Permanency of Marking .5657.1 General .5657.2 Oven-aging test 5657.3 Immersion tests 5757.4 Standard atmosphere test .57INSTRUCTIONS58 Instruction Manual 5759 Important Safety Instructions 66APART 2 DOUBLE-INSULATED CHAIN SAWSINTRODUCTION60 Scope .7161 Glossary .7162 General 73CONS

23、TRUCTION63 Accessibility of Live Parts 7564 Power-Supply Cords 7664.1 Flexible cord .7664.2 Strain relief 7664.3 Bushings 7664.4 Internal wiring 76A64.5 Attachment plug 7865 Capacitors .7866 Brush Caps 7867 Commutators and Armature End Turns 7868 Switches .7969 Brush Holders 7970 Spacings 80PERFORMA

24、NCE71 Dielectric Voltage-Withstand Test .8072 Leakage Current Test 80A73 Insulation Resistance Test .8274 Resistance to Impact Test .8375 Resistance to Heat Test .8576 Overload Test 8576.1 General .8576.2 Failure of sample to operate .87MARCH 31, 2006 ELECTRIC CHAIN SAWS - UL 1662 4AUL COPYRIGHTED M

25、ATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM UL76.3 Test terminated tool still operates .8977 Armature Investigation Test 9178 Leakage Current Following Humidity Test 9479 Dew Point Test .9580 Tests by the Manufacturer .95MARKING81 Details .96PART 3 ACCESSOR

26、IES AND ATTACHMENTSINTRODUCTION82 Scope .97CONSTRUCTION83 General 9784 Materials .9885 Sharp Edges and Projections 9886 Rotating Members 98PERFORMANCE87 Impact Testing .98MARKING88 Details .100INSTRUCTIONS89 General 10090 All Accessories and Attachments 101APPENDIX AStandards for ComponentsA1MARCH 3

27、1, 2006ELECTRIC CHAIN SAWS - UL 16624BUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULMARCH 31, 2006 ELECTRIC CHAIN SAWS - UL 1662 5No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERM

28、ISSION FROM ULThis page intentionally left blank.MARCH 31, 2006ELECTRIC CHAIN SAWS - UL 16626UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULPART 1 ALL CHAIN SAWSINTRODUCTION1 Scope1.1 These requirements cover electric chain saws rated not mor

29、e than 250 V, for use in accordance withthe National Electrical Code, NFPA 70.1.2 In addition these requirements cover accessories and attachments for use with electric chain saws.Specific requirements are outlined in Sections 82 90.1.3 These requirements cover double-insulated chain saws. Specific

30、requirements are given in Sections60 81.1.4 These requirements cover accessories and attachments that are:a) Recommended by the manufacturer;b) Identified by catalog number (or equivalent product designation) in the instruction manual fora chain saw; orc) Packed with a chain saw.1.4 revised April 1,

31、 19961.5 These requirements do not cover accessories or attachments that:a) Are not provided with the chain saw; andb) Are not identified in the required instruction manual by catalog numbers or equivalent productdesignation such as those mentioned in mini-catalogs or fliers that may or may not be p

32、rovidedwith the chain saw.1.6 A product that contains features, characteristics, components, materials, or systems new or differentfrom those covered by the requirements in this standard, and that involves a risk of fire or of electric shockor injury to persons shall be evaluated using appropriate a

33、dditional component and end-productrequirements to maintain the level of safety as originally anticipated by the intent of this standard. Aproduct whose features, characteristics, components, materials, or systems conflict with specificrequirements or provisions of this standard does not comply with

34、 this standard. Revision of requirementsshall be proposed and adopted in conformance with the methods employed for development, revision, andimplementation of this standard.2 Glossary2.1 For the purpose of these requirements, the following definitions apply.2.2 ACCESSORY A device such as a sprocket

35、that is attached only to the spindle of the unit.2.3 ATTACHMENT A device attached to the housing or other component of the chain saw and may ormay not be attached to the spindle. Attachments include replacement guards, guide bars, and saw chains.APRIL 1, 1996 ELECTRIC CHAIN SAWS - UL 1662 7UL COPYRI

36、GHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM UL2.4 LOW-KICKBACK SAW CHAIN A chain intended for use on any saw for which it is sized to fit andthat complies with the computed kickback angle requirements in Section 30, Kickback, when tested onrepresenta

37、tive samples, as described in the Safety Requirements for Gasoline Powered Chain Saws,ANSI B175.1-1991.2.5 REPLACEMENT SAW CHAIN A chain that, when used for field replacement on those specificlisted chain saws identified on the chain reel or package marking, will provide protection against rotarykic

38、kback for the saw and chain combination conforming to the requirements for kickback in 30.3.3 Components3.1 Except as indicated in 3.2, a component of a product covered by this standard shall comply with therequirements for that component. See Appendix A for a list of standards covering components g

39、enerallyused in the products covered by this standard.3.2 A component is not required to comply with a specific requirement that:a) Involves a feature or characteristic not required in the application of the component in theproduct covered by this standard, orb) Is superseded by a requirement in thi

40、s standard.3.3 A component shall be used in accordance with its rating established for the intended conditions ofuse.3.4 Specific components are incomplete in construction features or restricted in performance capabilities.Such components are intended for use only under limited conditions, such as c

41、ertain temperatures notexceeding specified limits, and shall be used only under those specific conditions.4 Units of Measurement4.1 Values stated without parentheses are the requirement. Values in parentheses are explanatory orapproximate information.CONSTRUCTION5 General5.1 A chain saw shall employ

42、 materials throughout that are acceptable for the particular use.6 Frame and Enclosure6.1 A chain saw shall be so formed and assembled that it will have the strength and rigidity necessary toresist the abuses to which it is likely to be subjected, without increasing the risk of fire, electric shock,

43、 orinjury to persons due to total or partial collapse with resulting reduction of spacings, loosening ordisplacement of parts, or other serious defects.6.2 The minimum thickness of cast metal shall be in accordance with Table 6.1.OCTOBER 14, 1994ELECTRIC CHAIN SAWS - UL 16628UL COPYRIGHTED MATERIAL

44、NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULTable 6.1Minimum thickness of cast metalAt surfaces that are reinforced by curving,ribbing, or the like (or are otherwise of ashape and/or size) to provide acceptablephysical strength,At unreinforced flat surfaces,Metal

45、 inch (mm) inch (mm)Die-cast metal 3/64 (1.2) 5/64 (2.0)Cast malleable iron 1/16 (1.6) 3/32 (2.4)Other cast metal 3/32 (2.4) 1/8 (3.2)6.3 An enclosure of sheet metal shall be considered with respect to its size, shape, thickness of metal,and its acceptability for the particular application, includin

46、g the intended use of the complete chain saw.6.4 Among the factors taken into consideration when determining the acceptability of a nonmetallicenclosure or an enclosure of magnesium are each of the following:a) Mechanical strength;b) Resistance to impact;c) Moisture-absorptive properties;d) Combusti

47、bility;e) Resistance to distortion at temperatures to which the material may be subjected underconditions of intended use and reasonably foreseeable abuse; andf) Resistance to arcing.6.5 *Deleted effective April 1, 1997*6.6 *Deleted effective April 1, 1997*6.7 During examination of a chain saw a par

48、t of the outer enclosure that is intended to be removedwithout the use of tools by the user of the chain saw (for the attachment of accessories, access to meansfor making operating adjustments, or other reasons) is to be disregarded that is, such a part is notconsidered to reduce the risk of electri

49、c shock.Revised 6.7 effective April 1, 19976.8 The enclosure of a chain saw shall exclude foreign matter (abrasive or electrically conductive particlesand the like) likely to be present during operation that might adversely affect electrical insulation orotherwise result in a risk of electric shock, fire, or injury to persons.APRIL 1, 1996 ELECTRIC CHAIN SAWS - UL 1662 9UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULFigure 6.1ProbeFigure 6.1 deleted effective