UL 10C-2016 UL Standard for Safety Positive Pressure Fire Tests of Door Assemblies (Third Edition).pdf

《UL 10C-2016 UL Standard for Safety Positive Pressure Fire Tests of Door Assemblies (Third Edition).pdf》由会员分享，可在线阅读，更多相关《UL 10C-2016 UL Standard for Safety Positive Pressure Fire Tests of Door Assemblies (Third Edition).pdf（27页珍藏版）》请在麦多课文档分享上搜索。

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 10C Positive Pressure Fire Tests of Door Assemblies STANDARD FOR SAFETYUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRIGHTE

2、D MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Positive Pressure Fire Tests of Door Assemblies, UL 10C Third Edition, Dated June 9, 2016 Summary of Topics The Third Edition of the Standard for Safety for Positive Pressure Fire

3、 Tests of Door Assemblies, UL 10C, has been issued to reect the latest ANSI approval date, and to incorporate the proposal dated April 15, 2016. This proposal includes the following: Oxygen percentage readings. The new requirements are substantially in accordance with Proposal(s) on this subject dat

4、ed April 15, 2016. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form by any means, electronic, mechanical photocopying, recording, or otherwise without prior permission of UL. UL provides this Standard as is without warranty

5、of any kind, either expressed or implied, including but not limited to, the implied warranties of merchantability or tness for any purpose. In no event will UL be liable for any special, incidental, consequential, indirect or similar damages, including loss of prots, lost savings, loss of data, or a

6、ny other damages arising out of the use of or the inability to use this Standard, even if UL or an authorized UL representative has been advised of the possibility of such damage. In no event shall ULs liability for any damage ever exceed the price paid for this Standard, regardless of the form of t

7、he claim. Users of the electronic versions of ULs Standards for Safety agree to defend, indemnify, and hold UL harmless from and against any loss, expense, liability, damage, claim, or judgment (including reasonable attorneys fees) resulting from any error or deviation introduced while purchaser is

8、storing an electronic Standard on the purchasers computer system. JUNE 9, 2016 UL 10C tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL JUNE 9, 2016 UL 10C tr2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCT

9、ION OR DISTRIBUTION WITHOUT PERMISSION FROM UL JUNE 9, 2016 1 UL 10C Standard for Positive Pressure Fire Tests of Door Assemblies Prior to the rst edition, the requirements for the products covered by this standard were included in the Standard for Fire Tests of Door Assemblies, UL 10B. First Editio

10、n February, 1998 Second Edition January, 2009 Third Edition June 9, 2016 This ANSI/UL Standard for Safety consists of the Third Edition. The most recent designation of ANSI/UL 10C as an American National Standard (ANSI) occurred on June 9, 2016. ANSI approval for a standard does not include the Cove

11、r Page, Transmittal Pages and Title Page. Comments or proposals for revisions on any part of the Standard may be submitted to UL at any time. Proposals should be submitted via a Proposal Request in ULs On-Line Collaborative Standards Development System (CSDS) at http:/. ULs Standards for Safety are

12、copyrighted by UL. Neither a printed nor electronic copy of a Standard should be altered in any way. All of ULs Standards and all copyrights, ownerships, and rights regarding those Standards shall remain the sole and exclusive property of UL. COPYRIGHT 2016 UNDERWRITERS LABORATORIES INC. ANSI/UL 10C

13、-2016UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL JUNE 9, 2016 POSITIVE PRESSURE FIRE TESTS OF DOOR ASSEMBLIES - UL 10C 2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSI

14、ON FROM UL CONTENTS INTRODUCTION 1 Scope .4 2 General 5 2.1 Units of measurement .5 2.2 Undated references .5 CONTROL OF FIRE TESTS 3 Furnace Construction 5 3.1 Furnace size .5 3.2 Furnace construction materials .5 3.3 Furnace burners 5 4 Time-Temperature Curve 6 4.1 General .6 4.2 Uniformity of tem

15、perature distribution .6 5 Furnace Temperatures 7 6 Unexposed Surface Temperatures and Cotton Pad Test .8 7 Furnace Pressure .9 TEST ASSEMBLIES 8 Construction and Size 12 9 Mounting for Test Purposes .12 CONDUCT OF TESTS 10 Supporting Construction .13 11 Fire Endurance Test 13 12 Hose Stream Test 13

16、 REPORT 13 General 14 CONDITIONS OF ACCEPTANCE 14 General 15 15 Specic 15 APPENDIX A A1 Standard Time-Temperature Curve for Control of Fire Tests .A1 APPENDIX B B1 Hose Stream Pattern .B1 JUNE 9, 2016 POSITIVE PRESSURE FIRE TESTS OF DOOR ASSEMBLIES - UL 10C 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FO

17、R FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL INTRODUCTION 1 Scope 1.1 These methods of re tests are applicable to swinging door assemblies, including door frames with lights and panels, of various materials and types of construction for use in wall openings to retard the passage

18、 of re. The method does not provide an evaluation of a swinging door assembly when that assembly is part of a larger assembly (e.g. sliding re door assembly), or when it is intended to be used as an elevator entrance. 1.2 Tests made in conformity with these test methods are intended to register perf

19、ormance during the test exposure; but such tests shall not be construed as determining suitability for use after exposure to re. 1.3 It is the intent that tests made in conformity with these test methods allow for the development of data to enable regulatory bodies to determine the suitability of do

20、or assemblies for use in locations where re resistance of a specied duration is required. 1.4 These methods are intended to evaluate the ability of a door assembly to remain in an opening during a predetermined test exposure. 1.5 The tests expose a specimen to a standard re exposure controlled to ac

21、hieve specied temperatures throughout a specied time period, followed by the application of a specied standard re hose stream. The exposure, however, is not representative of all re conditions, which vary with changes in the amount, nature, and distribution of re loading, ventilation, compartment si

22、ze and conguration, and heat sink characteristics of the compartment. It does, however, provide a relative measure of re performance of door assemblies under these specied re exposure conditions. 1.6 Any variation from the construction or conditions that are tested is capable of substantially changi

23、ng the performance characteristics of the assembly. 1.7 The methods do not provide the following: a) Full information as to performance of all door assemblies in walls constructed of materials other than those tested. b) Evaluation of the degree by which the door assembly contributes to the risk of

24、re by generation of smoke, toxic gases, or other products of combustion. c) A temperature limit on the unexposed side of the door assembly. d) A limit on the number of openings allowed in glazed areas or of the number and size of lateral openings between the door and frame. e) Measurement of the deg

25、ree of control or limitation of the passage of smoke or products of combustion through the door assembly. Note: See limitations for the passage of smoke detailed in the Standard for the Installation of Smoke Door Assemblies and Other Opening Protectives, NFPA 105. JUNE 9, 2016 POSITIVE PRESSURE FIRE

26、 TESTS OF DOOR ASSEMBLIES - UL 10C 4UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 2 General 2.1 Units of measurement 2.1.1 Values stated without parentheses are the requirement. Values in parentheses are explanatory or approximate informat

27、ion. 2.2 Undated references 2.2.1 Any undated reference to a code or standard appearing in the requirements of this standard shall be interpreted as referring to the latest edition of that code or standard. CONTROL OF FIRE TESTS 3 Furnace Construction 3.1 Furnace size 3.1.1 The furnace shall be able

28、 to accommodate the full-sized sample. Small-scale size furnaces are capable of being used for testing small but full-sized samples or representative features of full-sized samples. The furnace face shall be greater in area than the exposed face of the sample by at least 20 percent. The additional a

29、rea between the sample and the furnace shall be lled by wall or partition construction. 3.1.2 The furnace shall have a chamber depth, i.e. the distance between the exposed face of the specimen and the face of the furnace lining immediately opposite the specimen, of not less than 23 in (584 mm) and n

30、ot more than 51 in (1296 mm). 3.2 Furnace construction materials 3.2.1 The furnace shall be constructed of materials which have a greater resistance to heat ow through the other three sides than through the sample. 3.3 Furnace burners 3.3.1 The furnace shall be heated with burners that are red using

31、 either natural gas or liqueed petroleum gases. 3.3.2 The heat output of the burners shall be controllable and shall expose the specimen to a uniform heating as specied in 4.1.1. 3.3.3 The burners shall function so that the fuel gas is introduced into the furnace where the gas mixes with air present

32、 in the furnace and then burns; or, as an alternate, the fuel gas is mixed with air prior to its ignition in the furnace. JUNE 9, 2016 POSITIVE PRESSURE FIRE TESTS OF DOOR ASSEMBLIES - UL 10C 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL

33、4 Time-Temperature Curve 4.1 General 4.1.1 The re exposure of door assemblies shall be controlled to conform to the applicable portion of the standard time-temperature curve shown in Appendix A. The points on the curve that determine its character are: 1000F (538C) at 5 minutes 1300F (704C) at 10 mi

34、nutes 1462F (795C) at 20 minutes 1550F (843C) at 30 minutes 1638F (892C) at 45 minutes 1700F (927C) at 1 hour 1792F (978C) at 1-1/2 hours 1850F (1010C) at 2 hours 1925F (1052C) at 3 hours 2000F (1093C) at 4 hours 4.2 Uniformity of temperature distribution 4.2.1 At any time after the rst 10 minutes o

35、f re exposure, the temperature rise indicated by any of the thermocouples used to determine the furnace temperature shall not differ from each other by more than 270F (150C). With test constructions where either the sample or any associated construction incorporates combustible materials that produc

36、e aming within the furnace or where excess air drawn into the furnace is identied as causing localized heating or cooling of one or more of the furnace thermocouple hot junctions, the deviation of temperature rise from each other recorded by the thermocouples so affected shall not exceed 450F (250C)

37、. JUNE 9, 2016 POSITIVE PRESSURE FIRE TESTS OF DOOR ASSEMBLIES - UL 10C 6UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 5 Furnace Temperatures 5.1 The temperatures of the test exposure shall be the average temperature obtained by a minimum

38、of three thermocouples and no fewer than one thermocouple per 15 square feet of test assembly exposed to the furnace symmetrically disposed and distributed to show the temperature near all parts of the test assembly, Figure 5.1. The thermocouples shall be protected by: (1) sealed 1/2 in (12.7 mm) wr

39、ought-steel or wrought-iron pipe of standard weight or (2) Inconel 600 series schedule 40 pipe (0.8 inch OD / 0.6 inch ID, 20 mm OD / 15 mm ID). 5.2 The junction of the thermocouples shall be initially located 6 in (152 mm) from the exposed face of the test assembly or from the construction in which

40、 the assembly is installed. During the re exposure, if the movement of the test sample causes the samples distance to the thermocouple junction to vary, the location of the junction shall be reset to 6 in (152 mm) at intervals not exceeding 10 minutes during the rst 30 minutes of the test. Thereafte

41、r, the intervals are to be increased to not more than 30 minutes. 5.3 The temperatures shall be read at intervals not exceeding 1 minute. 5.4 The accuracy of the furnace control shall be such that the area under the time-temperature curve, obtained by averaging the results from the thermocouple read

42、ings, is within 10 percent of the corresponding area under the standard time-temperature curve for re tests of 1 hour or less duration, within 7.5 percent for those over 1 hour and not more than 2 hours, and within 5 percent for tests exceeding 2 hours in duration. 5.5 For a summary of the accuracie

43、s for the various rating periods, see Appendix A. This is generated text for gtxt. Figure 5.1 Test furnace JUNE 9, 2016 POSITIVE PRESSURE FIRE TESTS OF DOOR ASSEMBLIES - UL 10C 7UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 6 Unexposed Sur

44、face Temperatures and Cotton Pad Test 6.1 Unexposed surface temperatures are to be recorded, and are to be determined in accordance with 6.2 6.9. Exception: Single-layer metal doors need not comply with the requirements of 6.2 6.9. 6.2 Unexposed surface temperatures shall be taken at not less than t

45、hree points, with a minimum of one thermocouple in each 16-ft 2 (1.5 m 2 ) area of the door. Thermocouples shall not be located over reinforcements extending through the door, over glass panels, or nearer than 12 in (305 mm) from the edge of the door. 6.3 Surface temperatures of test specimens are t

46、o be measured by means of thermocouples with a wire diameter of not more than 0.03 in (0.7 mm). Each thermocouple is to be brazed to the center of the face of a copper disk 1/2 in (12 mm) in diameter and 0.01 in (0.2 mm) thick, which is secured to the surface of the specimen at the required position

47、. 6.4 Unexposed surface temperatures are to be measured with thermocouples placed under exible, oven-dry, felted pads. The properties of these felted pads are to comply with the requirements specied in Table 6.1. The felted pads are not to break when shaped to contact the surface against which they

48、are placed. Table 6.1 Felted Pad Characteristic Requirement Length and width 1.2 0.02 in (30 0.5 mm) Thickness a 0.08 0.02 in (2 0.5 mm) Density 56.2 6.2 lb/ft 3 (900 100 kg/m 3 Thermal conductivity at 150 F (66 C) 0.37 0.03 Btu-inch per hour per square foot per F (0.053 0.004 W/mK) Hardness b (on t

49、he soft face) 2.25 to 4.5 (modied Brinnell) a The thickness measurement is to be made under the light load of a 1/2 in (12.7-mm) diameter pad of a dial micrometer gage. b The hardness measurement is to be made by pressinga1i n(25.4 mm) diameter steel ball against the specimen and measuring the indentation obtained between a minor load of 2 pounds-mass (0.91 kg) and an additional major load of 10 pounds-mass (4.5 kg) 12 pounds-mass (5.4 kg) total lo