TIA-929-A-2009 Terrestrial Land Mobile Radio - Antenna Systems - Standard Format for Digitized Filter Characteristics《地面移动无线电通信 天线系统 数字化过滤器特性的标准格式 可访问其他内容》.pdf

《TIA-929-A-2009 Terrestrial Land Mobile Radio - Antenna Systems - Standard Format for Digitized Filter Characteristics《地面移动无线电通信 天线系统 数字化过滤器特性的标准格式 可访问其他内容》.pdf》由会员分享，可在线阅读，更多相关《TIA-929-A-2009 Terrestrial Land Mobile Radio - Antenna Systems - Standard Format for Digitized Filter Characteristics《地面移动无线电通信 天线系统 数字化过滤器特性的标准格式 可访问其他内容》.pdf（52页珍藏版）》请在麦多课文档分享上搜索。

1、 TIA-929-A-2009 APPROVED: DECEMBER 8, 2009 REAFFIRMED: OCTOBER 22, 2014 TIA-929-A (Revision of TIA-929) December 2009Terrestrial Land Mobile Radio - Antenna Systems - Standard Format for Digitized Filter Characteristics NOTICE TIA Engineering Standards and Publications are designed to serve the publ

2、ic interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for their particular need. The existence of such Standards

3、 and Publications shall not in any respect preclude any member or non-member of TIA from manufacturing or selling products not conforming to such Standards and Publications. Neither shall the existence of such Standards and Publications preclude their voluntary use by Non-TIA members, either domesti

4、cally or internationally. Standards and Publications are adopted by TIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, TIA does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the Standar

5、d or Publication. This Standard does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applicability of regulato

6、ry limitations before its use. Any use of trademarks in this document are for information purposes and do not constitute an endorsement by TIA or this committee of the products or services of the company. (From Project No. PN-3-0084-RV1-RF1, formulated under the cognizance of the TIA TR-8 Mobile and

7、 Personal Private Radio Standards. TR-8.11 Subcommittee on Antenna Systems). Published by TELECOMMUNICATIONS INDUSTRY ASSOCIATION Technology (b) there is no assurance that the Document will be approved by any Committee of TIA or any other body in its present or any other form; (c) the Document may b

8、e amended, modified or changed in the standards development or any editing process. The use or practice of contents of this Document may involve the use of intellectual property rights (“IPR”), including pending or issued patents, or copyrights, owned by one or more parties. TIA makes no search or i

9、nvestigation for IPR. When IPR consisting of patents and published pending patent applications are claimed and called to TIAs attention, a statement from the holder thereof is requested, all in accordance with the Manual. TIA takes no position with reference to, and disclaims any obligation to inves

10、tigate or inquire into, the scope or validity of any claims of IPR. TIA will neither be a party to discussions of any licensing terms or conditions, which are instead left to the parties involved, nor will TIA opine or judge whether proposed licensing terms or conditions are reasonable or non-discri

11、minatory. TIA does not warrant or represent that procedures or practices suggested or provided in the Manual have been complied with as respects the Document or its contents. If the Document contains one or more Normative References to a document published by another organization (“other SSO”) engag

12、ed in the formulation, development or publication of standards (whether designated as a standard, specification, recommendation or otherwise), whether such reference consists of mandatory, alternate or optional elements (as defined in the TIA Procedures for American National Standards) then (i) TIA

13、disclaims any duty or obligation to search or investigate the records of any other SSO for IPR or letters of assurance relating to any such Normative Reference; (ii) TIAs policy of encouragement of voluntary disclosure (see TIA Procedures for American National Standards Annex C.1.2.3) of Essential P

14、atent(s) and published pending patent applications shall apply; and (iii) Information as to claims of IPR in the records or publications of the other SSO shall not constitute identification to TIA of a claim of Essential Patent(s) or published pending patent applications. TIA does not enforce or mon

15、itor compliance with the contents of the Document. TIA does not certify, inspect, test or otherwise investigate products, designs or services or any claims of compliance with the contents of the Document. ALL WARRANTIES, EXPRESS OR IMPLIED, ARE DISCLAIMED, INCLUDING WITHOUT LIMITATION, ANY AND ALL W

16、ARRANTIES CONCERNING THE ACCURACY OF THE CONTENTS, ITS FITNESS OR APPROPRIATENESS FOR A PARTICULAR PURPOSE OR USE, ITS MERCHANTABILITY AND ITS NONINFRINGEMENT OF ANY THIRD PARTYS INTELLECTUAL PROPERTY RIGHTS. TIA EXPRESSLY DISCLAIMS ANY AND ALL RESPONSIBILITIES FOR THE ACCURACY OF THE CONTENTS AND M

17、AKES NO REPRESENTATIONS OR WARRANTIES REGARDING THE CONTENTS COMPLIANCE WITH ANY APPLICABLE STATUTE, RULE OR REGULATION, OR THE SAFETY OR HEALTH EFFECTS OF THE CONTENTS OR ANY PRODUCT OR SERVICE REFERRED TO IN THE DOCUMENT OR PRODUCED OR RENDERED TO COMPLY WITH THE CONTENTS. TIA SHALL NOT BE LIABLE

18、FOR ANY AND ALL DAMAGES, DIRECT OR INDIRECT, ARISING FROM OR RELATING TO ANY USE OF THE CONTENTS CONTAINED HEREIN, INCLUDING WITHOUT LIMITATION ANY AND ALL INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF BUSINESS, LOSS OF PROFITS, LITIGATION, OR THE LIKE), WHETH

19、ER BASED UPON BREACH OF CONTRACT, BREACH OF WARRANTY, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE FOREGOING NEGATION OF DAMAGES IS A FUNDAMENTAL ELEMENT OF THE USE OF THE CONTENTS HEREOF, AND THESE CONTENTS WOULD NOT BE PUBLISH

20、ED BY TIA WITHOUT SUCH LIMITATIONS. TIA-929-A ii Table of Contents DOCUMENT REVISION HISTORY . iii FOREWORD iv INTELLECTUAL PROPERTY RIGHTS v INTRODUCTION . vi 1 Scope . 3 2 References. 3 3 Definitions . 3 4 Requirements: ASCII Text Based Format . 3 4.1 General . 3 4.1.1 Overall Format 3 4.1.2 File

21、Naming . 4 4.2 The File Header 4 4.2.1 General . 4 4.2.2 File Header Record Characteristics 4 4.2.3 Record and Field parameters described . 5 4.3 Characteristics Data 9 4.3.1 General . 9 4.3.2 Data Header CONTACT MANUFACTURER”, as appropriate. 4.1.2 File Naming The filespec shall have a file extensi

22、on of “.FCD”, which stands for “filter characteristic data”. This standard does not specify a specific naming convention for the filename portion of the filespec; however, those who generate filter characteristic data are encouraged to include some reference to the model number and to the date the d

23、ata was taken. Because of compatibility issues, a filespec following the DOS 8.3 naming convention is encouraged, but is not required for compliance. 4.2 The File Header 4.2.1 General The file header consists of records that carry information not related to the devices characteristics data. 4.2.2 Fi

24、le Header Record Characteristics The header records to be used in digitized filter characteristics for the Terrestrial Land Mobile Radio Services are defined in Table 1. They are described in detail in the succeeding sub-clauses. Each header record begins with an abbreviated name field, ending in a

25、colon. If one or more data field follows the abbreviated name field, there is no field delimiter between the abbreviated name field and the first field following it. If there are two or more data fields, the comma (“,”) serves as a field delimiter. All data positions up to and including the decimal

26、point (if appropriate for the data type) shall be filled. Per-line comments may be added to any record. In any record, all data after a “!” character may be ignored. The record length, including the abbreviated record name but excluding the , shall not exceed the value specified in the Length column

27、. If the format is free form, then the record may be shorter than the maximum length, and shall be terminated with a carriage return and line feed characters. TIA-929-A 5 Table 1 File Header Record Characteristics Reqd? Field Name Length Abbreviated Descriptive (Char) Name Subclause x Standard Issue

28、 16 STDISS: 4.2.3.1 Comments1 80 COMNT1: 4.2.3.2 Comments2 80 COMNT2: 4.2.3.3 x Manufacturer 42 DEVMFR: 4.2.3.4 x Model Number 42 MODLNO: 4.2.3.5 x Device Type 31 DEVTYP: 4.2.3.6 x Date of Data 15 DTDATA: 4.2.3.7 x Lowest Tunable Frequency (MHz) 16 LOWFRQ: 4.2.3.8 x Highest Tunable Frequency (MHz) 1

29、6 HGHFRQ: 4.2.3.9 x Connector Type 1 22 CNTYP1: 4.2.3.10 Connector Type 2 22 CNTYP2: 4.2.3.10 Connector Type 3 22 CNTYP3: 4.2.3.10 Minimum Op Temp 16 LOTEMP: 4.2.3.11 Maximum Op Temp 15 HITEMP: 4.2.3.12 Height 21 DEVHGT: 4.2.3.13 * Width 21 DEVWTH: 4.2.3.14 * Depth 21 DEVDEP: 4.2.3.15 * Diameter 21

30、DEVDIA: 4.2.3.16 w Window Filter Insertion Loss 12 WININL: 4.2.3.17 w Window Filter Rejection 12 WINREJ: 4.2.3.18 x = 1 required per file * = Dimensional data consists of height plus either diameter or both width and depth w = Required only for window filters 4.2.3 Record and Field parameters descri

31、bed The following are detailed explanations of each of the data lines. The length of data specified includes all characters except . The symbols stand for Carriage Return / Line Feed. TIA-929-A 6 4.2.3.1 Standard Issue STDISS:XXXXXXXXX This is the version of this standard to which the data conforms.

32、 It shall include the complete standard number. For the “A” release, for example, it should indicate “TIA-929-A”. 4.2.3.2 Comments1 COMNT1:XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX This is a field for comments on the current revision. 4.2.3.3 Comments2 COMNT2:XXXXXXXX

33、XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX This is a field for comments on the current revision. 4.2.3.4 Device Manufacturer DEVMFR:XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX This is the name of the device manufacturer. Abbreviations shall not be used. 4.2.3.5 Full Model Number MODLN

34、O:XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX This is the full model number as used when the data was taken. Modifiers to the model number such as dashes or exceptions are to be included. This should uniquely identify the device and allow for revisions to the data. TIA-929-A 7 4.2.3.6 Device Type DEVTYP:XXX

35、XXXXXXXXXXXXXXXXXXXXX This is the type of device. It shall be one of the following: Bandpass Duplexer Bandpass Cavity Filter Pass-Notch Window Filter Pass-Reject Duplexer Notch Cavity Filter N*-Window Filter Multiplexer Pass-Notch Cavity Filter *Replace the “N” with the actual number of windows 4.2.

36、3.7 Date of Data DTDATA:YYYYMMDD This is the date the characteristics data was taken. 4.2.3.8 Lowest Tunable Frequency LOWFRQ:9999.9999 This is to identify the lowest frequency, in MHz, of the tunable range of the device 4.2.3.9 Highest Tunable Frequency HGHFRQ:9999.9999 This is to identify the high

37、est frequency, in MHz, of the tunable range of the device. 4.2.3.10 Connector Type 1 CNTYP1:XXXX,YYYYYYYY,ZZZZZZ This is the connector series and gender for external connection. The “X” fields describe the use of the external port: TX, RX, or ANT. If all or both ports are the same use “ALL” or “BOTH

38、”. The “Y” fields describe the connector series; e.g. “TYPE N”, “UHF”, “BNC”. The “Z” fields describe the gender of the connector mounted on the device (not the mating connector), i.e. “MALE” or “FEMALE”. If a single record is inadequate to describe the external connectors on a single device, use CN

39、TYP2:, CNTYP3:, etc. 4.2.3.11 Minimum Operating Temperature LOTEMP:-65C TIA-929-A 8 LOTEMP:-65C,-85F (optional) This is the lowest operating temperature for which the device is intended to operate at full specifications. The temperature shall be expressed in degrees Celsius. Optionally, the temperat

40、ure may be expressed in degrees Fahrenheit in addition to Celsius. The letter “C” and, if included, “F” shall be used to make clear which temperature scale is being used. 4.2.3.12 Maximum Operating Temperature HITEMP:85C HITEMP:85C,185F (optional) This is the highest operating temperature for which

41、the device is intended to operate at full specifications. The temperature shall be expressed in degrees Celsius. Optionally, the temperature may be expressed in degrees Fahrenheit in addition to Celsius. The letter “C” and, if included, “F” shall be used to make clear which temperature scale is bein

42、g used. 4.2.3.13 Device Height DEVHGT:1111MM DEVHGT:1111MM,43.74IN (optional) This is the physical height of the device. The height shall be expressed in millimeters. Optionally, it may be expressed in inches in addition to millimeters. The letters “MM” and, if included, “IN” shall be used to make c

43、lear which measurement units are being used. 4.2.3.14 Device Width DEVWTH:1111MM DEVWTH:1111MM,43.74IN (optional) This is the physical width of the device. The width shall be expressed in millimeters. Optionally, it may be expressed in inches in addition to millimeters. The letters “MM” and, if incl

44、uded, “IN” shall be used to make clear which measurement units are being used. Dimensions shall be expressed in either (a) height, width, and depth, or (b) height and diameter. Width and depth shall not be present if diameter is present. 4.2.3.15 Device Depth DEVDEP:1111MM TIA-929-A 9 DEVDEP:1111MM,

45、43.74IN (optional) This is the physical depth of the device. The depth shall be expressed in millimeters. Optionally, it may be expressed in inches in addition to millimeters. The letters “MM” and, if included, “IN” shall be used to make clear which measurement units are being used. Dimensions shall

46、 be expressed in either (a) height, width, and depth, or (b) height and diameter. Width and depth shall not be present if diameter is present. 4.2.3.16 Device Diameter DEVDIA:1111MM DEVDIA:1111MM,43.74IN (optional) This is the physical diameter of the device. The diameter shall be expressed in milli

47、meters. Optionally, it may be expressed in inches in addition to millimeters. The letters “MM” and, if included, “IN” shall be used to make clear which measurement units are being used. Dimensions shall be expressed in either (a) height, width, and depth, or (b) height and diameter. Diameter shall n

48、ot be present if width and depth are present. 4.2.3.17 Window Filter Insertion Loss WININL:XX.X This is the maximum insertion loss within the passband of a window filter, expressed in dB. This applies only to N Window filters. 4.2.3.18 Window Filter Rejection WINREJ:XXX.X This is the minimum rejecti

49、on provided by the window filter at frequencies outside the outer edge frequencies of the filter, expressed in dB. 4.3 Characteristics Data 4.3.1 General The characteristics data follows the header data. Each data file includes at least one set of characteristics data. In cases where a given manufacturers model number corresponds to more than one characteristic curve (for example, in the case of different coupling loops), characteristics data will be presented corresponding to each different curve. Because filter power ratin