SANS 62384-2008 DC or AC supplied electronic control gear for LED modules - Performance requirements《LED模块的直流及交流电子控制装置 性能要求》.pdf

《SANS 62384-2008 DC or AC supplied electronic control gear for LED modules - Performance requirements《LED模块的直流及交流电子控制装置 性能要求》.pdf》由会员分享，可在线阅读，更多相关《SANS 62384-2008 DC or AC supplied electronic control gear for LED modules - Performance requirements《LED模块的直流及交流电子控制装置 性能要求》.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA

2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any

3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 978-0-626-21801-0 SANS 62384:2008Edition 1IEC 62384:2006Edition 1SOUTH AFRICAN NATIONAL STANDARD DC or AC supplied electronic control gear for LED m

4、odules Performance requirements This national standard is the identical implementation of IEC 62384:2006 and is adopted with the permission of the International Electrotechnical Commission. WARNING Can only be used in conjunction with SANS 61347-2-13. Published by SABS Standards Division 1 Dr Latega

5、n Road Groenkloof Private Bag X191 Pretoria 0001 Tel: +27 12 428 7911 Fax: +27 12 344 1568 www.sabs.co.za SABS SANS 62384:2008 Edition 1 IEC 62384:2006 Edition 1 Table of changes Change No. Date Scope National foreword This South African standard was approved by National Committee SABS SC 64A, Light

6、ing and optics Lamps and auxiliaries, in accordance with procedures of the SABS Standards Division, in compliance with annex 3 of the WTO/TBT agreement. This SANS document was published in December 2008. NORME INTERNATIONALECEIIECINTERNATIONAL STANDARD 62384Premire ditionFirst edition2006-08Appareil

7、lages lectroniques aliments en courant continu ou alternatif pour modules de DEL Exigences de performances DC or AC supplied electronic control gear for LED modules Performance requirements Numro de rfrence Reference number CEI/IEC 62384:2006 SANS 62384:2008This s tandard may only be used and printe

8、d by approved subscription and freemailing clients of the SABS .62384 IEC:2006 3 CONTENTS FOREWORD.5 1 Scope.9 2 Normative references .9 3 Terms and definitions .9 4 General notes on tests .11 5 Classification11 5.1 Classification according to the load .11 5.2 Classification according to the output

9、voltage13 5.3 Classification according to the output current 13 6 Marking 13 6.1 Mandatory marking13 6.2 Optional marking .13 7 Output voltage and current .13 7.1 Starting and connecting requirements .13 7.2 Voltage and current during operation.15 7.3 Capacitive load requirement 15 7.4 Voltage surge

10、s during switching and operation15 8 Total circuit power 15 9 Circuit power factor 15 10 Supply current 15 11 Impedance at audio-frequencies.17 12 Operational tests for abnormal conditions.17 13 Endurance17 Annex A (normative) Tests.21 Annex B (informative) A guide to quoting product life and failur

11、e rate 27 Bibliography29 SANS 62384:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .62384 IEC:2006 5 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ DC OR AC SUPPLIED ELECTRONIC CONTROL GEAR FOR LED MODULES PERFORMANCE REQUIREMENTS FOREWORD 1

12、) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrica

13、l and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technica

14、l committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organizat

15、ion for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical com

16、mittee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications

17、is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and

18、 regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in con

19、formity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for

20、any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Norma

21、tive references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held respon

22、sible for identifying any or all such patent rights. International Standard IEC 62384 has been prepared by subcommittee 34C: Auxiliaries for lamps, of IEC technical committee 34: Lamps and related equipment The text of this standard is based on the following documents: FDIS Report on voting 34/752/F

23、DIS 34/760/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. SANS 62384:2008This s tandard may only be used and printed by approv

24、ed subscription and freemailing clients of the SABS .62384 IEC:2006 7 This standard is to be read in conjunction with IEC 61347-2-13. The committee has decided that the contents of this publication will remain unchanged until the maintenance result date indicated on the IEC web site under “http:/web

25、store.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed; withdrawn; replaced by a revised edition, or amended. SANS 62384:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .62384 IEC:2

26、006 9 DC OR AC SUPPLIED ELECTRONIC CONTROL GEAR FOR LED MODULES PERFORMANCE REQUIREMENTS 1 Scope This international standard specifies performance requirements for electronic control gear for use on d.c. supplies up to 250 V and a.c. supplies up to 1 000 V at 50 Hz or 60 Hz with an output frequency

27、which can deviate from the supply frequency, associated with LED modules according to IEC 62031. Control gear for LED modules specified in this standard are designed to provide constant voltage or current. Deviations from the pure voltage and current types do not exclude the gear from this standard.

28、 NOTE 1 The tests in this standard are type tests. Requirements for testing individual control gear during production are not included. NOTE 2 Requirements for control gear which incorporate means for varying the output power are under consideration. NOTE 3 It may be expected that control gear compl

29、ying with this standard will ensure satisfactory operation between 92 % and 106 % of the rated supply voltage, taking into account the specifications of the LED module manufacturer. 2 Normative references The following referenced documents are indispensable for the application of this document. For

30、dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 61347-2-13, Lamp controlgear Part 2-13: Particular requirements for d.c. or a.c. supplied electronic control gear for LED modules IEC 62031,

31、 LED modules for general lighting Safety requirements 1 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 total circuit power total power dissipated by control gear and LED module(s) in combination, at rated supply voltage of the control gear a

32、nd at the highest rated output load. 3.2 circuit power factor ratio of the measured circuit power to the product of the supply voltage (r.m.s.) and the supply current (r.m.s.). 3.3 high audio-frequency impedance control gear control gear the impedance of which in the frequency range 250 Hz to 2 000

33、Hz exceeds the values specified in Clause 11 of this standard. SANS 62384:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .62384 IEC:2006 11 4 General notes on tests 4.1 The tests according to this standard are type tests. NOTE The require

34、ments and tolerances permitted by this standard are based on testing of a type test sample submitted by the manufacturer for that purpose. In principle this type test sample should consist of units having characteristics typical of the manufacturers production and be as close to the production centr

35、e point values as possible. It may be expected with the tolerances given in the standard that products manufactured in accordance with the type test sample will comply with the standard for the majority of the production. Due to the production spread however, it is inevitable that there will sometim

36、es be products outside the specified tolerances. For guidance of sampling plans and procedures for inspection by attributes, see IEC 60410. 4.2 For tests which are carried out with a LED module or LED modules, this (these) LED module(s) shall fulfil the following requirements: The wattage of the LED

37、 module(s) when measured at its(their) rated voltage or rated current (d.c. and/or a.c.) shall not differ from the rated wattage by more than +6 % and 0 %. 4.3 The tests shall be carried out in the order of the clauses, unless otherwise specified. 4.4 One specimen shall be submitted to all the tests

38、. 4.5 In general all the tests are made on each type of control gear or, where a range of similar control gear is involved for each rated wattage in the range or on a representative selection from the range as agreed with the manufacturer. 4.6 The tests shall be made under the conditions specified i

39、n Clause A.1. Since up to now data of LED modules are not published in an IEC standard, they shall be made available by the LED module manufacturer. 4.7 All control gear covered by this standard shall comply with the requirements of IEC 61347-2-13. 4.8 The tests shall be carried out with the length

40、of the output cable of both 20 cm and 200 cm unless otherwise declared by the manufacturer. 5 Classification 5.1 Classification according to the load a) Single value load control gear This type of control gear is designed for use with one specific output wattage only, which may be dissipated by one

41、or more LED modules. b) Multiple value load control gear This type of control gear is designed for use with one or more LED modules with a total load within the declared wattage range. SANS 62384:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the

42、SABS .62384 IEC:2006 13 5.2 Classification according to the output voltage a) Control gear having a stabilised output voltage b) Control gear without a stabilised output voltage 5.3 Classification according to the output current a) Control gear having a stabilised output current b) Control gear with

43、out a stabilized output current 6 Marking 6.1 Mandatory marking 6.1.1 Control gear shall be clearly marked as follows: Circuit power factor; e.g. = 0,9 If the power factor is less than 0,95 leading, it shall be followed by the letter “C”, e.g. = 0,9 C. 6.1.2 In addition to the above mandatory markin

44、g, the following information shall either be given on the control gear or made available in the manufacturers catalogue or the like: a) if applicable: limits of the permissible temperature range; b) if applicable: an indication that the control gear has a stabilised output voltage; c) if applicable:

45、 an indication that the control gear has a stabilised output current; d) if applicable: an indication that the control gear is suitable for operation with a mains supply dimmer; e) if applicable: an indication of the operation mode, e.g. phase control. 6.2 Optional marking The following information

46、may either be given on the control gear or made available in the manufacturers catalogue or the like: a) total circuit power; b) if applicable: the symbol Z which indicates that the control gear is designed to comply with conditions for audio-frequency impedance; c) If applicable: a symbol which ind

47、icates that the control gear is a short-circuit proof type (the symbol is under consideration). 7 Output voltage and current 7.1 Starting and connecting requirements After starting or connecting a LED module, the output should be within 110 % of its rated value within 2 s. Maximum current or maximum

48、 voltage shall not exceed the values given by the manufacturer. This performance is tested with the minimum rated power. NOTE If the output voltage is a.c., 110 % is the percentage of the r.m.s. value, if d.c., 110 % is the percentage of the d.c. value. SANS 62384:2008This s tandard may only be used

49、 and printed by approved subscription and freemailing clients of the SABS .62384 IEC:2006 15 7.2 Voltage and current during operation For control gear having a non-stabilised output voltage, when supplied with the rated supply voltage, the output voltage shall not differ by more than 10 % from the rated voltage of the LED modules; for control gear having a stabilised output voltage when supplied at any supply voltage between 92 % and 106 % of the rated supply voltage, the output voltage shall