SANS 6011-2009 Cutting and marking of test specimens of particle boards《刨花板试样的切割和标志》.pdf

《SANS 6011-2009 Cutting and marking of test specimens of particle boards《刨花板试样的切割和标志》.pdf》由会员分享，可在线阅读，更多相关《SANS 6011-2009 Cutting and marking of test specimens of particle boards《刨花板试样的切割和标志》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA

2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any

3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 978-0-626-22632-9 SANS 6011:2009Edition 1.2Any reference to SABS SM 1011 is deemedto be a reference to this standard(Government Notice No. 1373 of 8

4、 November 2002)SOUTH AFRICAN NATIONAL STANDARD Cutting and marking of test specimens of particle boards Published by SABS Standards Division 1 Dr Lategan Road Groenkloof Private Bag X191 Pretoria 0001Tel: +27 12 428 7911 Fax: +27 12 344 1568 www.sabs.co.za SABS SANS 6011:2009 Edition 1.2 Table of ch

5、anges Change No. Date Scope Amdt 1 1992 Amended to change the references to ISO standards and to include references to two additional SABS methods. Amdt 2 2009 Amended to change the designation of SABS standards to SANS standards, and to update referenced standards. Foreword This South African stand

6、ard was approved by National Committee SABS SC 1008B, Wood and associated products Reconstituted timber, in accordance with procedures of the SABS Standards Division, in compliance with annex 3 of the WTO/TBT agreement. This document was published in September 2009. This document supersedes SABS SM

7、1011:1980 (edition 1, as amended 1992, reprint 1992). A vertical line in the margin shows where the text has been technically modified by amendment No. 2. SANS 6011:2009 Edition 1.2 1 Cutting and marking of test specimens of particle boards 1 Scope This method covers the position, cutting, and marki

8、ng of test specimens in a sample board. 2 Cutting 2.1 From the positions given in figure 2 or figure 3 (as relevant) in each sample board cut the 300 mm 300 mm test specimen(s) F and the appropriate of the 300 mm 600 mm modular sections (a), (b), (c), and (d). Then from the positions shown in figure

9、 1 cut from each modular section, the specimens for the remaining tests (see table 1). NOTE a) Figure 1 indicates the relative positions of the test specimens within a 300 mm 600 mm modular section, and the positions of these sections relative to the length and width of a sample board. Figures 2 and

10、 3 show the positioning of modular sections in boards of width at least 600 mm. Their positioning in narrower boards should be agreed upon between the sponsor and the testing authority. b) In the case of production quality control, whenever possible cut the sample boards alternately from the corner

11、of the leading and from the trailing half (in respect of the direction of production) of the particle board. 2.2 For the cutting operation use saws of adequate tooth shape (cross-cutting type), and ensure adequate saw speed to prevent burning and excessive heat development (especially during the pre

12、paration of moisture content and free formaldehyde content test specimens), and breaking out of pieces at an arris. NOTE Recommended sawing sequences (main cuts only) are given in figures 4 and 5. 2.3 Ensure that the dimensions of each test specimen, determined in accordance with ISO 9424 as an aver

13、age of the values at least three measuring positions, conform (to within the relevant tolerances) to the appropriate values given in column 4 of table 1, and that all arrises of a specimen are straight, clean cut, and square. NOTE In this method reference is made to the latest issues of ISO 9424 Woo

14、d-based panels Determination of dimensions of test pieces, ISO 9427 Wood-based panels Determination of density, ISO 16979 Wood-based panels Determination of moisture content, and SANS 6012, SANS 6013, SANS 6015, SANS 6016, SANS 6018, SANS 6019. Amdt 1; amdt 2 2.4 Place the density plus moisture cont

15、ent specimens and the free formaldehyde specimens into airtight containers immediately after cutting and marking, and, in the case of free formaldehyde specimens, maintain the container(s) at 3 C 2 C until they are tested. SANS 6011:2009 Edition 1.2 2 3 Marking of test specimens 3.1 General Mark the

16、 same face of each test specimen (when relevant, the face-side of the sample board) with the specimen identification given in 3.2. Where relevant, use an indelible marking medium which remains legible even after treatment of the specimens. Apply markings in a position where failure of the specimen o

17、r obliteration is not expected. Where markings are covered during testing (see SANS 6016), transfer such markings to the loading block. 3.2 Specimen identification 3.2.1 General Identify a specimen by the sample board identification, the cutting identification, and the test identification. 3.2.2 Sam

18、ple board identification Identify a sample board by a code representing the manufacturer, type, thickness, and number of the sample board (given in that sequence) followed, when relevant, by the letters FR, TR, or FTR, as appropriate, e.g. A2181 where A = code designation allotted to manufacturer; 2

19、 = type of board, i.e. interior or exterior; 18 = nominal thickness of board, mm; 1 = number of sample board. NOTE For factory control tests, the manufacturers identification should be replaced by the batch number or production date. 3.2.3 Cutting identification Identify the modular section from whi

20、ch a specimen was cut by the appropriate of the lower case letters “a“ to “d“ (see figures 2 and 3). 3.2.4 Test identification Identify (preferably by the number/letter designation of the test method) the method of test for which the specimen is intended. SANS 6011:2009 Edition 1.2 3 Table 1 Dimensi

21、ons of test specimens and number per modular section 1 2 3 4 5 Identification of method of test Property Dimensions of test specimen, mma Number of test specimens per modular section ISO 9427 and ISO 16979 Density and moisture content (100 1) (100 1) t 1 Thickness swelling (for t 35 mm, and that for

22、 boards thinner than 9 mm, the dimensions are 300 mm (150 0,5) mm. Amdt 1; amdt 2 SANS 6011:2009 Edition 1.2 4 Dimensions in millimetres Figure 1 Modular section positions relative to length and width of sample board SANS 6011:2009 Edition 1.2 5 Dimensions in millimetres Do not cut any test specimen

23、 (or part of specimen) form the dark area in figure 2. NOTE Sections (b), (c) and (d) are similar section (d) is a mirror image of (b), (c) and (d). Figure 2 Cutting plan for test specimens of particle board (other than profiled flooring) of width 1 200 mm SANS 6011:2009 Edition 1.2 6 Dimensions in

24、millimetres Figure 3 Cutting plan for profiled flooring boards and other boards of width less than 1 200 mm SANS 6011:2009 Edition 1.2 7 Dimensions in millimetres 10 mm sawing allowed between sections. Figure 4 Recommended sawing sequence for separation of modular sections (a), (b), (c) and (d) and

25、the impact resistance samples for sample boards of width at least 1 200 mm (main cuts only) SANS 6011:2009 Edition 1.2 8 Dimensions in millimetres Figure 5 Enlargement of modular sections (b), (c) and (d) in accordance with figures 2 and 3 showing the recommended sawing pattern and sequence (main cu

26、ts only) SABS SABS Standards Division The objective of the SABS Standards Division is to develop, promote and maintain South African National Standards. This objective is incorporated in the Standards Act, 2008 (Act No. 8 of 2008). Amendments and Revisions South African National Standards are update

27、d by amendment or revision. Users of South African National Standards should ensure that they possess the latest amendments or editions. The SABS continuously strives to improve the quality of its products and services and would therefore be grateful if anyone finding an inaccuracy or ambiguity whil

28、e using this standard would inform the secretary of the technical committee responsible, the identity of which can be found in the foreword. Tel: +27 (0) 12 428 6666 Fax: +27 (0) 12 428 6928 The SABS offers an individual notification service, which ensures that subscribers automatically receive noti

29、fication regarding amendments and revisions to South African National Standards. Tel: +27 (0) 12 428 6883 Fax: +27 (0) 12 428 6928 E-mail: salessabs.co.za Buying Standards Contact the Sales Office for South African and international standards, which are available in both electronic and hardcopy form

30、at. Tel: +27 (0) 12 428 6883 Fax: +27 (0) 12 428 6928 E-mail: salessabs.co.za South African National Standards are also available online from the SABS website http:/www.sabs.co.za Information on Standards The Standards Information Centre provides a wide range of standards-related information on both

31、 national and international standards, and is the official WTO/TBT enquiry point for South Africa. The Centre also offers an individual updating service called INFOPLUS, which ensures that subscribers automatically receive notification regarding amendments to, and revisions of, international standar

32、ds. Tel: +27 (0) 12 428 6666 Fax: +27 (0) 12 428 6928 E-mail: infosabs.co.za Copyright The copyright in a South African National Standard or any other publication published by the SABS Standards Division vests in the SABS. Unless exemption has been granted, no extract may be reproduced, stored in a

33、retrieval system or transmitted in any form or by any means without prior written permission from the SABS Standards Division. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any purpose other than implementation, prior written permission must be obtained. Details and advice can be obtained from the Senior Manager. Tel: +27 (0) 12 428 6666 Fax: +27 (0) 12 428 6928 E-mail: infosabs.co.za