SANS 3452-2-2009 Non-destructive testing - Penetrant testing Part 2 Testing of penetrant materials《无损检测 渗透检测 第2部分 渗透材料测试》.pdf

《SANS 3452-2-2009 Non-destructive testing - Penetrant testing Part 2 Testing of penetrant materials《无损检测 渗透检测 第2部分 渗透材料测试》.pdf》由会员分享，可在线阅读，更多相关《SANS 3452-2-2009 Non-destructive testing - Penetrant testing Part 2 Testing of penetrant materials《无损检测 渗透检测 第2部分 渗透材料测试》.pdf（40页珍藏版）》请在麦多课文档分享上搜索。

1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA

2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any

3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 978-0-626-22530-6 SANS 3452-2:2009Edition 2ISO 3452-2:2006Edition 2SOUTH AFRICAN NATIONAL STANDARD Non-destructive testing Penetrant testing Part 2:

4、 Testing of penetrant materials This national standard is the identical implementation of ISO 3452-2:2006 and is adopted with the permission of the International Organization for Standardization. Published by SABS Standards Division 1 Dr Lategan Road Groenkloof Private Bag X191 Pretoria 0001Tel: +27

5、 12 428 7911 Fax: +27 12 344 1568 www.sabs.co.za SABS SANS 3452-2:2009 Edition 2 ISO 3452-2:2006 Edition 2 Table of changes Change No. Date Scope National foreword This South African standard was approved by National Committee SABS TC 135, Engineering materials Non-destructive testing, in accordance

6、 with procedures of the SABS Standards Division, in compliance with annex 3 of the WTO/TBT agreement. This SANS document was published in September 2009. This SANS document supersedes SANS 3452-2:2000 (edition 1). Reference numberISO 3452-2:2006(E)ISO 2006INTERNATIONAL STANDARD ISO3452-2Second editi

7、on2006-08-15Non-destructive testing Penetrant testing Part 2: Testing of penetrant materials Essais non destructifs Examen par ressuage Partie 2: Essais des produits de ressuage SANS 3452-2:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .

8、ISO 3452-2:2006(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In down

9、loading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the

10、 General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address

11、given below. ISO 2006 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs mem

12、ber body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2006 All rights reservedSANS 3452-2:2009This s tandard may only be used and printed by

13、 approved subscription and freemailing clients of the SABS .ISO 3452-2:2006(E) ISO 2006 All rights reserved iiiContents Page Foreword iv 1 Scope . 1 2 Normative references . 1 3 Terms and definitions. 1 4 Classification. 2 4.1 Testing products. 2 4.2 Sensitivity levels. 2 5 Testing of penetrant mate

14、rials 3 5.1 Testing facilities 3 5.2 Reporting . 3 5.3 Tests. 4 6 Test methods and requirements . 6 6.1 Appearance . 6 6.2 Penetrant system sensitivity . 6 6.3 Density . 11 6.4 Viscosity 11 6.5 Flashpoint 12 6.6 Washability (Method A penetrants). 12 6.7 Fluorescent brightness 12 6.8 UV stability 13

15、6.9 Thermal stability of fluorescent brightness.13 6.10 Water tolerance . 13 6.11 Corrosive properties. 14 6.12 Content of sulfur and halogens (for products designated low in sulfur and halogens) . 17 6.13 Residue on evaporation/solid content 18 6.14 Penetrant tolerance 18 6.15 Developer performance

16、 18 6.16 Redispersability 18 6.17 Density of carrier liquid 19 6.18 Product performance (pressurized containers) 19 6.19 Particle size distribution 19 6.20 Water content 19 7 Packaging and labelling. 19 Annex A (normative) Comparison of fluorescent brightness 20 Annex B (normative) Process control t

17、ests 22 Annex C (informative) Equipment for determination of the visibility of fluorescent indications 31 Bibliography . 32 SANS 3452-2:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO 3452-2:2006(E) iv ISO 2006 All rights reservedFore

18、word ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a techn

19、ical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

20、electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to

21、 the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for

22、identifying any or all such patent rights. ISO 3452-2 was prepared by the European Committee for Standardization (CEN) Technical Committee CEN/TC 138, Non-destructive testing, in collaboration with Technical Committee ISO/TC 135, Non-destructive testing, Subcommittee SC 2, Surface methods, in accord

23、ance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement). This second edition cancels and replaces the first edition (ISO 3452-2:2000), which has been technically revised. ISO 3452 consists of the following parts, under the general title Non-destructive testing Penetra

24、nt testing: General principles Part 2: Testing of penetrant materials Part 3: Reference test blocks Part 4: Equipment SANS 3452-2:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .INTERNATIONAL STANDARD ISO 3452-2:2006(E) ISO 2006 All right

25、s reserved 1Non-destructive testing Penetrant testing Part 2: Testing of penetrant materials SAFETY PRECAUTIONS The materials required by this part of ISO 3452 include chemicals which may be harmful, flammable and/or volatile. All necessary precautions shall be observed. All relevant International,

26、national and local regulations pertaining to health and safety, environmental requirements, etc. shall be observed. 1 Scope This part of ISO 3452 specifies the technical requirements and test procedures for penetrant materials for their type testing and batch testing. It also details on-site control

27、 tests and methods. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 30

28、59, Non-destructive testing Penetrant testing and magnetic particle testing Viewing conditions ISO 3452-3, Non-destructive testing Penetrant testing Part 3: Reference test blocks ISO 12706, Non-destructive testing Terminology Terms used in penetrant testing ISO/IEC 17025, General requirements for th

29、e competence of testing and calibration laboratories EN 571-1, Non-destructive testing Penetrant testing Part 1: General principles 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 12706, EN 571-1 and the following apply. 3.1 batch quantity of materia

30、l produced at one operation having uniform properties throughout and with a unique identifying number or mark 3.2 candidate sample of the testing product submitted for evaluation in accordance with this part of ISO 3452 SANS 3452-2:2009This s tandard may only be used and printed by approved subscrip

31、tion and freemailing clients of the SABS .ISO 3452-2:2006(E) 2 ISO 2006 All rights reserved4 Classification 4.1 Testing products Penetrant testing products shall be classified by type, method and form in accordance with Table 1. Table 1 Testing products Penetrant Excess penetrant remover Developer T

32、ype Denomination Method Denomination Form Denomination I Fluorescent penetrant A Water a Dry II Colour contrast penetrant B Lipophilic emulsifier: b Water soluble 1 Oil-based emulsifier 2 Rinsing with running water c Water suspendible III Dual-purpose (fluorescent colour contrast penetrant) C Solven

33、t (liquid): Class 1 Halogenated Class 2 Non-halogenated Class 3 Special application d Solvent-based (non-aqueous for Type I) D Hydrophilic emulsifier: 1 Optional pre-rinse (water) 2 Emulsifier (water-diluted) 3 Final rise (water) e Solvent-based (non-aqueous for Types II and III) E Water and solvent

34、 f Special application 4.2 Sensitivity levels 4.2.1 General Sensitivity levels shall be defined separately for penetrant, excess penetrant remover and developer, and for product families. 4.2.2 Fluorescent product family Sensitivity levels for this product family shall be defined by reference produc

35、ts: sensitivity level 1/2 (ultra-low); sensitivity level 1 (low); sensitivity level 2 (medium); sensitivity level 3 (high); sensitivity level 4 (ultra-high). SANS 3452-2:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO 3452-2:2006(E) I

36、SO 2006 All rights reserved 34.2.3 Colour contrast product family Sensitivity levels for this product family shall be defined using the type 1 reference block in accordance with ISO 3452-3: sensitivity level 1 (normal); sensitivity level 2 (high). 4.2.4 Dual-purpose product family There are no sensi

37、tivity levels for dual-purpose penetrants. Classification may be carried out as for colour contrast systems (see 4.2.3). 5 Testing of penetrant materials 5.1 Testing facilities 5.1.1 Type testing Type testing shall be carried out on penetrant materials according to EN 571-1 to ensure their conforman

38、ce to the requirements of this part of ISO 3452. Type testing shall be carried out by a laboratory accredited in accordance with ISO/IEC 17025 for type testing of penetrant materials. 5.1.2 Batch testing Batch testing to the requirements of this part of ISO 3452 shall be carried out on each producti

39、on batch according to EN 571-1 to ensure the batch has the same properties as the corresponding type approval sample. In the case of penetrant material packed in spray cans, the content of sulfur and halogens shall be additionally determined according to 6.12. Batch testing shall be carried out unde

40、r a defined and maintained quality system. A system meeting the requirements of ISO 9001 is considered suitable. 5.1.3 Process control testing Process control testing shall be carried out or commissioned by the user in accordance with EN 571-1 and ISO 3452-3. 5.2 Reporting 5.2.1 Type testing The tes

41、ting laboratory (see 5.1.1) shall provide a certificate of compliance with this part of ISO 3452 and a report that details the results obtained. If any changes are made to the penetrant material composition, then a new type test and product identity shall be required. SANS 3452-2:2009This s tandard

42、may only be used and printed by approved subscription and freemailing clients of the SABS .ISO 3452-2:2006(E) 4 ISO 2006 All rights reserved5.2.2 Batch testing Manufacturers of penetrant materials shall provide certificates of compliance with this part of ISO 3452 (for example, see EN 10204). 5.2.3

43、Process and control testing Results obtained shall be recorded (see Annex B). 5.3 Tests 5.3.1 Penetrants Type and batch testing of penetrant properties shall be carried out in accordance with Table 2. Table 2 Properties of penetrants and required tests Property Test type Use test method according to

44、 Appearance Batch 6.1 Sensitivity Type and batch 6.2 Density Type and batch 6.3 Viscosity Type and batch 6.4 Flashpoint Type and batch 6.5 Washability (Method A penetrants only) Batch 6.6 Fluorescent brightness (Type I penetrants) Type and batch 6.7 UV stability (Type I penetrants) Type 6.8 Thermal

45、stability (Type I penetrants) Type 6.9 Water tolerance (Method A penetrants only) Type 6.10 Corrosive properties Type and batch 6.11 Content of sulfur and halogens aType and batch 6.12 Water content (Methods A and E) Batch 6.20 Other contaminants on request (as required) Batch aOnly required for pro

46、ducts designated “low in sulfur and halogens”. 5.3.2 Excess penetrant removers (excluding method A) Type and batch testing of penetrant remover properties shall be carried out in accordance with Table 3. SANS 3452-2:2009This s tandard may only be used and printed by approved subscription and freemai

47、ling clients of the SABS .ISO 3452-2:2006(E) ISO 2006 All rights reserved 5Table 3 Properties of excess penetrant removers and required tests Property Test type Use test method according to Appearance Batch 6.1 Sensitivity Type and batch 6.2 Density Type and batch 6.3 Viscosity (for Methods B and D

48、only) Type and batch 6.4 Flashpoint Type and batch 6.5 Water tolerance (Method B only) Type and batch 6.10 Corrosive properties Type and batch 6.11 Content of sulfur and halogens aType and batch 6.12 Residue on evaporation/solid content Type and batch 6.13 Penetrant tolerance (Methods B and D only)

49、Type 6.14 Water content (Method B only) Batch 6.20 Other contaminants on request (as required) Batch aOnly required for products designated “low in sulfur and halogens”. 5.3.3 Developers Type and batch testing of developer properties shall be carried out in accordance with Table 4. Table 4 Properties of developers and required tests Property Test type Use test method according to Appearance Batch 6.1 Sensitivity Type and batch 6.2 Flashpoint (Form d only) Type and batch 6.5 Corrosive