SANS 2860-2003 Earth-moving machinery - Minimum access dimensions《土方机械 最小通道尺寸》.pdf

《SANS 2860-2003 Earth-moving machinery - Minimum access dimensions《土方机械 最小通道尺寸》.pdf》由会员分享，可在线阅读，更多相关《SANS 2860-2003 Earth-moving machinery - Minimum access dimensions《土方机械 最小通道尺寸》.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA

2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any

3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ICS 53.100 ISBN 0-626-15026-4 SANS 2860:2003 Edition 1 ISO 2860:1992 Edition 4 SOUTH AFRICAN NATIONAL STANDARD Earth-moving machinery Minimum access dime

4、nsions This national standard is the identical implementation of ISO 2860:1992 and is adopted with the permission of the International Organization for Standardization. Published by Standards South Africa 1 dr lategan road groenkloof private bag x191 pretoria 0001 tel: 012 428 7911 fax: 012 344 1568

5、 international code + 27 12 www.stansa.co.za Standards South Africa 2003 SANS 2860:2003 Edition 1 ISO 2860:1992 Edition 4 Table of changes Change No. Date Scope Abstract Specifies the minimum dimensions for: hand, head, body, arm and two-handed access on equip-ment and machinery as defined in SANS 2

6、61. Keywords access openings, dimensions, earth-moving equipment, ergonomics, holes, human body, mechanical engineering, minimal values, operators (personnel), specification (approval). National foreword This South African standard was approved by National Committee STANSA TC 5120.38, Earth-moving a

7、nd forestry machinery, in accordance with procedures of Standards South Africa, in compliance with annex 3 of the WTO/TBT agreement. INTERNATIONAL STANDARD 2860 Fourth edition 1992-02-l 5 Earth-moving machinery - Minimum access dimensions Engins de terrassemen t - Dimensions minimales des passages R

8、eference number IS0 2860: 1992(E) IS0 2860:1992(E) Foreword IS0 (the International Organization for Standardization) is a worldwide federation of national standards bodies (IS0 member bodies). The work of preparing International Standards is normally carried out through IS0 technical committees. Eac

9、h member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, govern- mental and non-governmental, in liaison with ISO, also take part in the work. IS0 collaborates closely with the Internati

10、onal Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an lnter- national Standard requires approval by at least 75 % of the member bod

11、ies casting a vote. International Standard IS0 2860 was prepared by Technical Committee ISO/TC 127, Earth-moving machinery, Sub-Committee SC 2, Safety re- quirements and human factors. This fourth edition cancels and replaces the third edition (IS0 2860:1983), of which it constitutes a technical rev

12、ision. 0 IS0 1992 All rights reserved. No part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfllm, without permission in writing from the publisher. International Organization for Standardization Case Postale

13、56 l CH-121 I Geneve 20 l Switzerland Printed in Switzerland ii INTERNATIONAL STANDARD IS0 2860:1992(E) Earth-moving machinery - Minimum access dimensions 1 Scope This International Standard specifies the minimum access openings on earth-moving machinery as de- fined in IS0 6165 for a) hand access,

14、b) head access, c) body access, d) arm access, e) two-handed access. It provides engineers and designers with information in order that the access openings provided on equipment and machinery for purposes of in- spection, adjustment and maintenance have suffi- cient dimensions for the intended funct

15、ion by personnel in the field or shop. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this International Standard. At the time of publi- cation, the editions indicated were valid. All stan- dards are subject to revisi

16、on, and parties to agreements based on this International Standard are encouraged to investigate the possibility of ap- plying the most recent editions of the standards in- dicated below. Members of IEC and IS0 maintain registers of currently valid International Standards. IS0 3411:1982, Earth-movin

17、g machinery - Human physical dimensions of operators and minimum op- erator space envelope. IS0 6165:1987, Earth-moving machinery - Basic types - Vocabulary. 3 Minimum access openings The dimensions shown in 3.1 to 3.4 are the rec- ommended minimum for limited activity through the opening. Larger op

18、enings will be needed in specific instances, depending upon the nature of the task, size and mass of the parts, etc. Such larger openings can be more useful and allow greater ef- ficiency. The larger openings for access with arctic clothing are for earth-moving machines and equipment in- tended for

19、use in cold environments. Based on available anthropometric data, the rec- ommended openings, in figures 1 to 5, are the smallest that will accommodate the 95th percentile operator as defined in IS0 3411. In all cases in 3.1 to 3.4, all corners may have an optional maximum 25 mm radius. IS0 2860:199

20、2(E) 3.1 Hand access 3.2 Head access Hand access shall be in accordance with figure 1. Dimensions in millimetres m,s 1 Royd 1 bRectara; Hand bare 110 65 110 With arctic mitten 150 100 150 Head access shall be in accordance with figure2. Dimensions in millimetres - Minimum dimensions I Round I Rectan

21、gular I d h 2 Head bare 230 210 230 With arctic cloth- ing) 300 280 300 With hat, helmet 330 I 290 I 330 I 1) Arctic clothing includes parka hood. Figure 2 - Minimum dimensions for head access, 95th percentile Figure 1 - Minimum dimensions for hand access, 95th percentile 2 IS0 2860:1992(E) 3.3 Body

22、 access 3.4 Reach access Body access shall be in accordance with figure 3. a) TOD and bottom access b1 Slde access Dimensions in millimetres Minimum dimensions Ellipse d D Top and bottom access Normal clothing I 330 I 580 I With arctic clothing I 470 I 690 I Side access Normal clothing 660 760 With

23、arctic clothing I 740 I 870 I 3.4.1 Arm access Arm access shall be in accordance with figure4. Dimensions in millimetres Minimum dimensions (one arm) Round d . Rectangular 6 I I Arm bare I 200 I 150 I 200 I With arctic cloth- ing / 250 1 200 1 250 1 Figure 4 - Minimum dimensions for arm access, 95th

24、 percentile Figure 3 - Minimum dimensions for body access, 95th percentile IS0 2860:1992(E) 3.4.2 Two-handed access Two-handed access shall be in accordance with fig- ure 5. I between hands + 11 J- + 50 mm wlth arctic clothing *) h= required reach. Dimensions in millimetres Minimum dimensions (two hands) Arms bare 150 With arctic clothing I 1) b- width of opening. Rectangular b 1) 200 2 $+I, (2OOQhG560) 1 -f h + 50 i- 2, (250GhG650) 1 Figure 5 - Minimum dimensions for two-handed access, 95th percentile