SANS 20020-2008 Uniform provisions concerning the approval of motor vehicle headlamps emitting an asymmetrical passing beam or a driving beam or both and equipped with halogen fila.pdf

《SANS 20020-2008 Uniform provisions concerning the approval of motor vehicle headlamps emitting an asymmetrical passing beam or a driving beam or both and equipped with halogen fila.pdf》由会员分享，可在线阅读，更多相关《SANS 20020-2008 Uniform provisions concerning the approval of motor vehicle headlamps emitting an asymmetrical passing beam or a driving beam or both and equipped with halogen fila.pdf（71页珍藏版）》请在麦多课文档分享上搜索。

1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA

2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any

3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 978-0-626-21014-4 SANS 20020:2008Edition 2ECE R20:2006Revision 3 SOUTH AFRICAN NATIONAL STANDARD Uniform provisions concerning the approval of motor

4、 vehicle headlamps emitting an asymmetrical passing beam or a driving beam or both and equipped with halogen filament lamps (H4lamps) This national standard is the identical implementation of ECE R20:2006 and is adopted with the permission of the United Nations Economic Commission for Europe. Publis

5、hed by Standards South Africa 1 1 dr lategan road groenkloof private bag x191 pretoria 000x: 012 344 1568 international code +27 12 tel: 012 428 7911 fawww.stansa.co.za Standards South Africa SANS 20020:2008 Edition 2 ECE R20:2006 Revision 3 Table of changes Change No. Date Scope National foreword T

6、his South African standard was approved by National Committee StanSA TC 5120.71, Lighting and optics for traffic and transport, in accordance with procedures of Standards South Africa, in compliance with annex 3 of the WTO/TBT agreement. This SANS document was published in February 2008. This SANS d

7、ocument supersedes SANS 20020:1992 (edition 1 as modified by ECE amdt 1:1994, ECE amdt 2:1995, ECE amdt 3:1998, ECE amdt 4:2001 and nat. amdt 1:2003). The text of the ECE document is reproduced unaltered. For the compulsory application of this standard, the stringency level, the date of entry into f

8、orce and any additional requirements, if needed, are published in the applicable compulsory specification in the Government Gazette. Any compulsory introduction of this standard by reference through national or provincial legislation should be subject to stakeholder consultation, before publication

9、in the legislative notice and before the effective date. E/ECE/324 E/ECE/TRANS/505Rev.1/Add.19/Rev.3 10 October 2006 AGREEMENT CONCERNING THE ADOPTION OF UNIFORM TECHNICAL PRESCRIPTIONS FOR WHEELED VEHICLES, EQUIPMENT AND PARTS WHICH CAN BE FITTED AND/OR BE USED ON WHEELED VEHICLES AND THE CONDITION

10、S FOR RECIPROCAL RECOGNITION OF APPROVALS GRANTED ON THE BASIS OF THESE PRESCRIPTIONS / (Revision 2, including the amendments which entered into force on 16 October 1995) _ Addendum 19: Regulation No. 20 Revision 3 Incorporating all valid text up to : Supplement 4 to the 02 series of amendments - Da

11、te of entry into force: 5 March 1994 Supplement 5 to the 02 series of amendments - Date of entry into force: 27 November 1994 Corrigendum 1 to Supplement 3 to the 02 series of amendments, subject of Depositary Notification C.N.317.1994.TREATIES-38 dated 30 November 1994 Corrigendum 1 to Revision 2 o

12、f the Regulation, subject of Depositary Notification C.N.207.1995.TREATIES-36 dated 4 August 1995 Supplement 6 to the 02 series of amendments - Date of entry into force: 25 December 1997 03 series of amendments */ - Date of entry into force: 9 September 2001 UNIFORM PROVISIONS CONCERNING THE APPROVA

13、L OF MOTOR VEHICLE HEADLAMPS EMITTING AN ASYMMETRICAL PASSING BEAM OR A DRIVING BEAM OR BOTH AND EQUIPPED WITH HALOGEN FILAMENT LAMPS (H4 LAMPS) _ UNITED NATIONS / Former title of the Agreement: Agreement Concerning the Adoption of Uniform Conditions of Approval and Reciprocal Recognition of Approva

14、l for Motor Vehicle Equipment and Parts, done at Geneva on 20 March 1958. */ Not requiring changes in the approval number (TRANS/WP.29/815, para. 82). GE.06- E/ECE/324 E/ECE/TRANS/505Rev.1/Add.19/Rev.3 Regulation No. 20 page 3 Regulation No. 20UNIFORM PROVISIONS CONCERNING THE APPROVAL OF MOTOR VEHI

15、CLE HEADLAMPS EMITTING AN ASYMMETRICAL PASSING BEAM OR A DRIVING BEAM OR BOTH AND EQUIPPED WITH HALOGEN FILAMENT LAMPS (H4LAMPS) CONTENTS REGULATION PageA. ADMINISTRATIVE PROVISIONS 5 - Scope . 5 1. Definitions . 5 2. Application for approval of a headlamp . 6 3. Markings 7 4. Approval 7 B. TECHNICA

16、L REQUIREMENTS FOR HEADLAMPS . 12 5. General specifications . 12 6. Illumination 13 7. Provisions concerning coloured lenses and filters . 18 8. Gauging of discomfort . 19 9. Standard (reference) headlamp 19 10. Observation concerning colour . 19 C. FURTHER ADMINISTRATIVE PROVISIONS 19 11. Modificat

17、ion of the headlamp type and extension of approval 19 12. Conformity of production 20 13. Penalties for non-conformity of production 21 E/ECE/324 E/ECE/TRANS/505 Rev.1/Add.19/Rev.3 Regulation No. 20 page 4 CONTENTS (continued) 14. Production definitely discontinued 21 15. Names and addresses of Tech

18、nical Services responsible for conducting approval tests, and of Administrative Departments 22 16. Transitional provisions . 23 ANNEXES Annex 1 - Communication concerning the approval or refusal or extension or withdrawal of approval (or production definitely discontinued) for a type of headlamp pur

19、suant to Regulation No. 20 Annex 2 - Arrangements of approval marks Annex 3 - Measuring screen Annex 4 - Tests for stability of photometric performance of headlamps in operation Annex 5 - Minimum requirements for conformity of production control procedures Annex 6 - Requirements for lamps incorporat

20、ing lenses of plastic material - testing of lens or material samples and of complete lamps Appendix 1 Chronological order of approval tests Appendix 2 Method of measurement of the diffusion and transmission of light Appendix 3 Spray testing method Appendix 4 Adhesive tape adherence test Annex 7 - Mi

21、nimum requirements for sampling by an inspector E/ECE/324 E/ECE/TRANS/505Rev.1/Add.19/Rev.3 Regulation No. 20 page 5 A. ADMINISTRATIVE PROVISIONS SCOPE 1/ This Regulation applies to motor vehicle headlamps which may incorporate lenses of glass or plastic material. 1. DEFINITIONS For the purpose of t

22、his Regulation, 1.1. “Lens“ means the outermost component of the headlamp (unit) which transmits light through the illuminating surface; 1.2. “Coatinq“ means any product or products applied in one or more layers to the outer face of a lens; 1.3. Headlamps of different “types“ are headlamps which dif

23、fer in such essential respects as: 1.3.1. the trade name or mark; 1.3.2. the characteristics of the optical system; 1.3.3. the inclusion or elimination of components capable of altering the optical effects by reflection, refraction, absorption and/or deformation during operation. However, the fittin

24、g or elimination of filters intended solely to change the colour of the beam but not its light distribution does not entail a change of type; 1.3.4. suitability for right-hand or left-hand traffic or for both traffic systems; 1.3.5. the kind of beam produced (passing beam, driving beam or both); 1.3

25、.6. the materials constituting the lenses and coating, if any. 1/ Nothing in this Regulation shall prevent a Party to the Agreement applying this Regulation from prohibiting the combination of a headlamp incorporating a lens of plastic material approved under this Regulation with a mechanical headla

26、mp-cleaning device (with wipers). E/ECE/324 E/ECE/TRANS/505 Rev.1/Add.19/Rev.3 Regulation No. 20 page 6 2. APPLICATION FOR APPROVAL OF A HEADLAMP 2/ 2.1. The application for approval shall be submitted by the owner of the trade name or mark or by his duly accredited representative. It shall specify:

27、 2.1.1. whether the headlamp is intended to provide both a passing beam and a driving beam or only one of these beams; 2.1.2. whether, if the headlamp is intended to provide a passing beam, it is designed for both left-hand and right-hand traffic or for either left-hand or right-hand traffic only; 2

28、.1.3. if the headlamp is equipped with an adjustable reflector, the mounting position(s) of the headlamp in relation to the ground and the longitudinal median plane of the vehicle. 2.2. Every application for approval shall be accompanied by: 2.2.1. drawings in triplicate in sufficient detail to perm

29、it identification of the type and representing a frontal view of the headlamp, with details of lens ribbing if any, and the cross-section; the drawings shall indicate the space reserved for the approval mark; 2.2.1.1. if the headlamp is equipped with an adjustable reflector, an indication of the mou

30、nting position(s) of the headlamp in relation to the ground and the longitudinal median plane of the vehicle, if the headlamp is for use in that (those) position(s) only; 2.2.2. a brief technical description; 2.2.3. two samples of the type of headlamp; 2.2.3.1. for the testing of a coloured filter o

31、r coloured screen (or of a coloured lens): two samples. 2.2.4. For the test of plastic material of which the lenses are made: 2.2.4.1. thirteen lenses; 2.2.4.1.1. six of these lenses may be replaced by six samples of material at least 60 x 80 mm in size, having a flat or convex outer surface and a s

32、ubstantially flat area (radius of curvature not less than 300 mm) in the middle measuring at least 15 x 15 mm; 2/ Application for approval of a filament lamp: see Regulation No. 37. E/ECE/324 E/ECE/TRANS/505Rev.1/Add.19/Rev.3 Regulation No. 20 page 7 2.2.4.1.2. every such lens or sample of material

33、shall be produced by the method to be used in mass production; 2.2.4.2. a reflector to which the lenses can be fitted in accordance with the manufacturers instructions. 2.3. The materials making up the lenses and coatings, if any, shall be accompanied by the test report of the characteristics of the

34、se materials and coatings if they have already been tested. 2.4. The Competent Authority shall verify the existence of satisfactory arrangements for ensuring effective control on conformity of production before type approval is granted. 3. MARKINGS 3/ 3.1. Headlamps submitted for approval shall bear

35、 the trade name or mark of the applicant. 3.2. They shall comprise, on the lens and on the main body, 4/ spaces of sufficient size for the approval mark and the additional symbols referred to in paragraph 4.; these spaces shall be indicated on the drawings referred to in paragraph 2.2.1. above. 3.3.

36、 Headlamps designed to satisfy the requirements both of right-hand and of left-hand traffic shall bear markings indicating the two settings of the optical unit on the vehicle or of the filament lamp on the reflector; these markings shall consist of the letters “R/D“ for the position for right-hand t

37、raffic and the letters “L/G“ for the position for left-hand traffic. 4. APPROVAL 4.1. General4.1.1. If all the samples of a type of headlamp submitted pursuant to paragraph 2 above satisfy the provisions of this Regulation, approval shall be granted. 3/ In the case of headlamps designed to meet the

38、requirements of traffic moving on one side of the road only (either right or left), it is further recommended that the area which can be occulted to prevent discomfort to users in a country where traffic moves on the side of the road opposite to that of the country for which the headlamp was designe

39、d should be outlined indelibly on the front lens. This marking is not necessary, however, where the area is clearly apparent from the design. 4/ If the lens cannot be detached from the main body of the headlamp, a space on the lens shall be sufficient. E/ECE/324 E/ECE/TRANS/505 Rev.1/Add.19/Rev.3 Re

40、gulation No. 20 page 8 4.1.2. Where grouped, combined or reciprocally incorporated lamps satisfy the requirements of more than one Regulation, a single international approval mark may be affixed provided that each of the grouped, combined or reciprocally incorporated lamps satisfies the provisions a

41、pplicable to it. 4.1.3. An approval number shall be assigned to each type approved. Its first two digits (at present 02) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting

42、Party may not assign the same number to another type of headlamp covered by this Regulation, except if the approval is extended to a device which only differs from the already approved device by the colour of the light emitted. 4.1.4. Notice of approval or of extension or refusal or withdrawal of ap

43、proval or production definitely discontinued of a type of headlamp pursuant to this Regulation shall be communicated to the Parties to the 1958 Agreement applying this Regulation, by means of a form conforming to the model shown in Annex 1 to this Regulation, with the indications according to paragr

44、aph 2.2.1.1. 4.1.4.1. if the headlamp is equipped with an adjustable reflector and if this headlamp is to be used only in mounting positions according to the indications in paragraph 2.2.1.1., the applicant shall be obliged by the Approval Authority to inform the user in a proper way about the corre

45、ct mounting position(s). 4.1.5. In addition to the mark prescribed in paragraph 3.1, an approval mark as described in paragraphs 4.2. and 4.3. below shall be affixed in the spaces referred to in paragraph 3.2. above to every headlamp conforming to a type approved under this Regulation. 4.2. Composit

46、ion of the approval markThe approval mark shall consist of: 4.2.1. An international approval marking, comprising: E/ECE/324 E/ECE/TRANS/505Rev.1/Add.19/Rev.3 Regulation No. 20 page 9 4.2.1.1. a circle surrounding the letter “E“ followed by the distinguishing number of the country which has granted a

47、pproval; 5/ 4.2.1.2. the approval number prescribed in paragraph 4.1.3. above; 4.2.2. the following additional symbol (or symbols): 4.2.2.1. on headlamps meeting left-hand traffic requirements only, a horizontal arrow pointing to the right of an observer facing the headlamp, i.e. to the side of the

48、road on which the traffic moves; 4.2.2.2. on headlamps designed to meet the requirements of both traffic systems by means of an appropriate adjustment of the setting of the optical unit or the filament lamp, a horizontal arrow with a head on each end, the heads pointing respectively to the left and

49、to the right; 4.2.2.3. on headlamps meeting the requirements of this Regulation in respect of the passing beam only, the letters “HC“; 4.2.2.4 on headlamps meeting the requirements of this Regulation in respect of the driving beam only, the letters “HR“; 4.2.2.5. on headlamps meeting the requirements of this Regulation in respect of both the passing beam and the driving beam, the letters “HCR“; 5/ 1 for Germany, 2 for France, 3 for Italy, 4 for the Netherlands, 5 for Sweden, 6 for Belgium, 7 for Hungary, 8 for the Czech Republic, 9 for Spain, 10 for Ser