SANS 17660-1-2009 Welding - Welding of reinforcing steel Part 1 Load-bearing welded joints《焊接 钢筋焊接 第1部分:承载焊接节点》.pdf
《SANS 17660-1-2009 Welding - Welding of reinforcing steel Part 1 Load-bearing welded joints《焊接 钢筋焊接 第1部分:承载焊接节点》.pdf》由会员分享,可在线阅读,更多相关《SANS 17660-1-2009 Welding - Welding of reinforcing steel Part 1 Load-bearing welded joints《焊接 钢筋焊接 第1部分:承载焊接节点》.pdf(48页珍藏版)》请在麦多课文档分享上搜索。
1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA
2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any
3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 978-0-626-23478-2 SANS 17660-1:2009Edition 1ISO 17660-1:2006Edition 1SOUTH AFRICAN NATIONAL STANDARD Welding Welding of reinforcing steel Part 1: Lo
4、ad-bearing welded joints This national standard is the identical implementation of ISO 17660-1:2006 and is adopted with the permission of the International Organization for Standardization. Published by SABS Standards Division 1 Dr Lategan Road Groenkloof Private Bag X191 Pretoria 0001Tel: +27 12 42
5、8 7911 Fax: +27 12 344 1568 www.sabs.co.za SABS SANS 17660-1:2009 Edition 1 ISO 17660-1:2006 Edition 1 Table of changes Change No. Date Scope National foreword This South African standard was approved by National Committee SABS TC 44, Welding and allied processes, in accordance with procedures of th
6、e SABS Standards Division, in compliance with annex 3 of the WTO/TBT agreement. This SANS document was published in November 2009. Reference numberISO 17660-1:2006(E)ISO 2006INTERNATIONAL STANDARD ISO17660-1First edition2006-09-01Welding Welding of reinforcing steel Part 1: Load-bearing welded joint
7、s Soudage Soudage des aciers darmatures Partie 1: Assemblages transmettant des efforts SANS 17660-1:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO 17660-1:2006(E) PDF disclaimer This PDF file may contain embedded typefaces. In accord
8、ance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes lic
9、ensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printi
10、ng. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2006 All rights reserved. Unless otherwise specified, no part of this pu
11、blication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Ge
12、neva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2006 All rights reservedSANS 17660-1:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO 17660-1:2006(E) ISO 2006
13、 All rights reserved iiiContents Page Foreword iv Introduction v 1 Scope . 1 2 Normative references . 1 3 Terms and definitions. 2 4 Symbols and abbreviated terms . 3 5 Welding processes . 4 6 Load-bearing welded joints . 4 7 Materials 14 8 Quality requirements 14 9 Welding personnel 15 10 Welding p
14、rocedure specification (WPS).16 11 Welding procedures . 16 12 Production weld test. 18 13 Execution and inspection of production welding of reinforcing steel 19 14 Examination and testing of test specimens. 21 15 Production log. 24 Annex A (informative) Welding procedure specification (WPS) for weld
15、ing processes 111, 114, 135 and 136 25 Annex B (informative) Technical knowledge of welding coordinator for welding reinforcing steel . 27 Annex C (informative) Test specimens 28 Annex D (informative) Assessment of the manufacturer performing welding 32 Annex E (informative) Evaluation of testing of
16、 welded joints 33 Annex F (informative) Example for production log. 34 Annex G (informative) Classification of shear strength of load-bearing cross joints. 35 Annex H (informative) Examples of diameter combinations for welding cross joints using welding processes 21 and 23. 36 Bibliography . 37 SANS
17、 17660-1:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO 17660-1:2006(E) iv ISO 2006 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO memb
18、er bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, government
19、al and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Direct
20、ives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodie
21、s casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 17660-1 was prepared by the European Committee for Standardization (CEN) Techni
22、cal Committee CEN/TC 121, Welding, in collaboration with Technical Committee ISO/TC 44, Welding and allied processes, Subcommittee SC 10, Unification of requirements in the field of metal welding, in accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement). ISO 1
23、7660 consists of the following parts, under the general title Welding Welding of reinforcing steel: Part 1: Load-bearing welded joints Part 2: Non load-bearing welded joints Requests for official interpretations of any aspect of this part of ISO 17660 should be directed to the Secretariat of ISO/TC
24、44/SC 10 via your national standards body. A complete listing of these bodies can be found at www.iso.org. SANS 17660-1:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO 17660-1:2006(E) ISO 2006 All rights reserved vIntroduction Reinfor
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- SANS1766012009WELDINGWELDINGOFREINFORCINGSTEELPART1LOADBEARINGWELDEDJOINTS 焊接 钢筋 部分 承载 节点 PDF
链接地址:http://www.mydoc123.com/p-1029790.html