SANS 10188-2008 Standard methods of garment measurement《服装测量标准方法》.pdf

《SANS 10188-2008 Standard methods of garment measurement《服装测量标准方法》.pdf》由会员分享，可在线阅读，更多相关《SANS 10188-2008 Standard methods of garment measurement《服装测量标准方法》.pdf（64页珍藏版）》请在麦多课文档分享上搜索。

1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA

2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any

3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 978-0-626-20980-3 SANS 10188:2008Edition 2.1Any reference to SABS 0188 is deemedto be a reference to this standard(Government Notice No. 1373 of 8 N

4、ovember 2002)SOUTH AFRICAN NATIONAL STANDARD Standard methods of garment measurement Published by Standards South Africa 1 dr lategan road groenkloof private bag x191 pretoria 0001 tel: 012 428 7911 fax: 012 344 1568 international code + 27 12 www.stansa.co.za Standards South Africa SANS 10188:2008

5、Edition 2.1 Table of changes Change No. Date Scope Amdt 1 2008 Amended to change the designation of SABS standards to SANSstandards, with no technical changes. Foreword This South African standard was approved by National Committee StanSA SC 5110.05A, Clothing and made-up articles Clothing, in accor

6、dance with procedures of Standards South Africa, in compliance with annex 3 of the WTO/TBT agreement. This document was published in February 2008. This document supersedes SABS 0188:2002 (edition 2). SANS 10188:2008 Edition 2.1 1 Contents Page Foreword 1 Scope . 3 2 Normative references . 3 3 Defin

7、itions 3 4 Garment categories 3 5 Procedure . 4 5.1 General 4 5.2 Category A: Overcoats, raincoats, blazers and uniform tunics . 5 5.3 Category B: Shorts, slacks, long underpants and tracksuit pants . 12 5.4 Category C: Waistcoats . 17 5.5 Category D: Shirts and blouses . 19 5.6 Category E: Dresses

8、and gowns . 25 5.7 Category F: Skirts and similar items of outerwear/underwear . 28 5.8 Category G: Cardigans, pullovers, jerseys, jumpers and sweaters . 30 5.9 Category H: Vests, T-shirts, spencers and singlets 34 5.10 Category I: Underpants, briefs and panties . 37 5.11 Category J: Camisoles and b

9、rassieres 40 5.12 Category K: One-piece coveralls . 42 5.13 Category L: Ties and cravats . 47 5.14 Category M: Gloves . 52 5.15 Category N: Aprons . 53 5.16 Category O: Socks, pantyhose and knee-highs 54 5.17 Category P: Headgear . 57 SANS 10188:2008 Edition 2.1 2 This page is intentionally left bla

10、nk SANS 10188:2008 Edition 2.1 3 Standard methods of garment measurement 1 Scope This standard defines the various measuring points used to determine the dimensions of various categories of garments. 2 Normative references The following standards contain provisions which, through reference in this t

11、ext, constitute provisions of this standard. All standards are subject to revision, and since any reference to a standard is deemed to be a reference to the latest edition of that standard, parties to agreements based on this standard are encouraged to take steps to ensure the use of the most recent

12、 editions of the standards indicated below. Information on currently valid national and international standards can be obtained from Standards South Africa. SANS 1382-1 (SABS 1382-1), Hose Part 1: Mens and womens hose for institutional use. SANS 5766, Measurements of girth and length extended dimens

13、ions of pantyhose. SANS 10004, Terms and definitions for textiles and textile merchandise. 3 Definitions For the purposes of this standard, the relevant definitions given in SANS 10004 apply. 4 Garment categories For the purposes of this standard, the garments covered are divided into the following

14、categories: Category A Coats and similar items of outerwear that cover the whole or only the upper part of the body, e.g. overcoats, jackets, raincoats, blazers, uniform tunics. Category B Trousers and similar garments that cover only the lower part of the body, e.g. shorts,slacks, long underpants a

15、nd tracksuit pants. Category C Sleeveless tailored garments of the waistcoat type that cover only the upper part of thebody. Category D Shirts and similar items of outerwear for men, women and children that cover only theupper part of the body. Category E Dresses, gowns and similar items of outerwea

16、r for women and girls that cover the whole body. SANS 10188:2008 Edition 2.1 4 Category F Skirts and similar items of outerwear/underwear for women and girls that cover only thelower part of the body e.g half slips. Category G Knitted items of outerwear that cover only the upper part of the body, e.

17、g. cardigans, pullovers, jerseys, jumpers and sweaters. Category H Vests and similar items of underwear/outerwear that cover only the upper part of thebody, e.g. spencers, singlets and T-shirts. Category I Underpants and similar items of underwear that cover only the lower part of the body,e.g. brie

18、fs and panties. Category J Brassieres and similar items of underwear that cover only the upper part of the body,e.g. camisoles. Category K One-piece coveralls and similar items of outerwear that cover the whole of the body, e.g. flight suits. Category L Ties and similar items of neckwear, e.g. bow t

19、ies. Category M Gloves. Category N Aprons. Category O Socks and similar items of hosiery, e.g. pantyhose and knee-highs. Category P Headgear, e.g. baseball caps, beanie caps and flight caps. 5 Procedure 5.1 General When appropriate, so lay the garment out (with buttons fastened and slide fasteners c

20、losed, unless otherwise stated) on a smooth flat surface that it is free from folds, wrinkles and creases and, using a tape measure graduated in centimetres and millimetres, measure the appropriate dimensions in accordance with categories A to P. SANS 10188:2008 Edition 2.1 5 5.2 Category A: Overcoa

21、ts, raincoats, blazers and uniform tunics Coats and similar items of outerwear that cover the whole or only the upper part of the body, e.g. overcoats, jackets, raincoats, blazers and uniform tunics. Figure 1 Figure 3 Figure 2 Measuring point Description A - A Bust/chest circumference see figures 1

22、and 2 Measure across the width of the garment at the base of the scye, with the garment spread completely flat and multiply by two. A - A Bust/chest circumference (with gusset) see figure 3 Measure across the width of the garment at the base of the scye, below the gusset insert, with the garment spr

23、ead completely flat and multiply by two.SANS 10188:2008 Edition 2.1 6 Figure 4 Figure 5 Measuring point Description Measure across the width of the garment, at a point below the centre back neck point (determined by using the table in accordance with the appropriate figure type and height) and multi

24、ply by two. Men Women Children RS RR RL RS RR RL At waist level B - B Waist circumference see figures 4 and 5 43 cm 45 cm 47 cm 38 cm 40 cm 42 cm Measure across the width of the garment, at a point below the waist (determined by using the table in accordance with the appropriate figure type and heig

25、ht) and multiply by two. Men Women Children RS RR RL RS RR RL At hip/seat level C - C Hip/seat circumference see figures 4 and 5 18 cm 20 cm 22 cm 18 cm 20 cm 22 cm D - D Bottom hem circumference see figures 4 and 5 Measure across the width at the bottom hem of the garment and multiply by two. SANS

26、10188:2008 Edition 2.1 7 Figure 6 Figure 7 Measuring point Description E - E Back width (plain back) see figure 6 Measure across the width of the back, at the midpoint of the scye, from sleeve seam to sleeve seam. E - E Back width (back with yoke) see figure 7 Measure across the width of the back, a

27、t the yoke-to-back panel seam, from sleeve seam to sleeve seam. F - F Depth of scye see figures 6 and 7 Measure the depth from the centre back neck seam to the level of the base of the scye. SANS 10188:2008 Edition 2.1 8 Figure 8 Figure 9 Figure 10 Measuring point Description F - G Back length (plai

28、n hem) see figure 8 Measure from the centre back neck seam to the bottom edge of the hem.F - G Back length (with waistband) see figure 9 Measure from the centre back neck seam to the bottom edge of the waistband (with garment flattened out). H - H Waistband circumference (relaxed) see figure 9 Measu

29、re across the width at the bottom edge of the waistband and multiply by two. H - H Waistband circumference (extended) see figure 10 Measure across the width at the bottom edge of the waistband, with the waist-band fully extended, and multiply by two. SANS 10188:2008 Edition 2.1 9 Figure 11 Measuring

30、 point Description I - I Neck length see figure 11 Measure the full length of the collar along the gorge seam. Figure 12 Figure 13 SANS 10188:2008 Edition 2.1 10 Figures (concluded) Figure 14 Figure 15 Sleeves Measuring point Description A - J Sleeve length see figures 12 and 13 Measure from the bas

31、e of the scye along the underarm seam to the bottom edge of the sleeve/cuff. A - J Sleeve length (sleeve with gusset) see figure 14 Measure from the bottom edge of the gusset, along the underarm seam to the bottom edge of the sleeve/cuff. J - K Sleeve length (cut-on) see figure 15 Measure from the n

32、eck point to the bottom edge of the sleeve/cuff. SANS 10188:2008 Edition 2.1 11 Figure 17 Figure 16 Figure 18 Figure 19 Figure 20 Cuffs Measuring point Description J - J Cuff circumference (plain or elasticized cuff, relaxed) see figures 16 and 17 Measure across the width at the bottom edge of the c

33、uff and multiply by two. J - J Cuff circumference (elasticized cuff, extended) see figures 18 Measure across the width at the bottom edge of the cuff, with the cuff fully extended, and multiply by two. J - J Cuff circumference (separate cuff with press studs) see figures 19 Measure across the width

34、at the bottom edge of the cuff, with the cuff fastened (to first press stud) and multiply by two. J - J Cuff circumference (separate cuff with buttons) see figures 20 Measure across the width at the bottom edge of the cuff, with the cuff fastened (to first button) and multiply by two. SANS 10188:200

35、8 Edition 2.1 12 5.3 Category B: Shorts, slacks, long underpants and tracksuit pants Trousers and similar garments that cover only the lower part of the body, e.g. shorts, slacks, long underpants and tracksuit pants. Figure 1 Figure 2 Figure 3 Figure 4 Measuring point Description A - A Seat/hip circ

36、umference (plain fronts, with fly opening) see figures 1 and 3 Measure across the width of the garment at seat/hip level (widest point) and multiply by two. A - A Seat/hip circumference (pleated fronts, with fly opening) see figure 2 Measure across the width of the garment at seat/hip level (widest

37、point) with open pleats, and multiply by two. A - A Seat/hip circumference (elasticised waistband, without fly opening) see figure 4 Measure across the width of the garment at seat/hip level (widest point) and multiply by two. SANS 10188:2008 Edition 2.1 13 Figure 5 Figure 6 Figure 7 Measuring point

38、 Description B - B Waist circumference (plain or elasticized, relaxed) see figures 5 and 6 Measure across the top edge of the waistband (front and back top edges aligned) and multiply by two. B - B Waist circumference (elasticized, extended) see figure 7 Measure across the top edge of the waistband

39、(front and back top edges aligned), with the waistband fully extended, and multiply by two.SANS 10188:2008 Edition 2.1 14 Figure 9 Figure 8 Figure 10 Measuring point Description C - C Inside leg length see figures 8, 9 and 10 Measure from the crotch seam to the bottom edge of the garment. D - D Outs

40、ide leg length see figures 8, 9 and 10 Measure from the top edge of the waistband to the bottom edge of the garment. SANS 10188:2008 Edition 2.1 15 Figure 11 Figure 12 Measuring point Description D - E Rise see figures 11 and 12 Measure the length, determined by subtracting the inside leg length fro

41、m the outside leg length. SANS 10188:2008 Edition 2.1 16 Figure 13 Figure 14 Figure 15 Measuring point Description C - D Bottom hem circumference (turn-ups or plain hem) see figures 13 and 15 Measure across the width, at the bottom edge of the leg/turn-up and multiply by two. C - D Bottom hem circum

42、ference (with adjustment straps) see figure 14 Measure across the width, at the bottom edge of the leg with the adjustment straps unfastened and multiply by two. F - F Knee circumference see figure 15 Measure across the width, 50 mm above the position determined by folding the bottom edge of the leg

43、 to the crotch line, and multiply by two.SANS 10188:2008 Edition 2.1 17 5.4 Category C: Waistcoats Sleeveless tailored garments of the waistcoat type that cover only the upper part of the body. Figure 1 Figure 2 Measuring point Description A - A Bust/chest circumference see figure 1 Measure across t

44、he width of the garment at the base of the scye, with the garment spread completely flat, and multiply by two. Measure across the width of the garment, at a point below the centre back neck point (determined by using the table in accordance with the appropriate figure type and height) and multiply b

45、y two. Men Women RS RR RL RS RR RL B - B Waist circumference (plain back) see figure 1 43 cm 45 cm 47 cm 38 cm 40 cm 42 cm Measure across the width of the garment, with the waist straps loose, at a point below the centre back neck point (determined by using the table in accordance with the appropria

46、te figure type and height) and multiply by two. Men Women RS RR RL RS RR RL B - B Waist circumference (with waist straps) see figure 2 43 cm 45 cm 47 cm 38 cm 40 cm 42 cm SANS 10188:2008 Edition 2.1 18 Figure 3 Figure 4 Measuring point Description C - C Front length see figure 3 Measure the length i

47、n a straight line from the neck point (on the natural shoulder line) down to the bottom point/edge of the garment. D - D Back length see figure 4 Measure the length from the centre back neck point to the bottom edge of the garment. D - E Neck drop see figure 3 Measure the length from the centre back

48、 neck point to the point of overlap (bottom of “V“). SANS 10188:2008 Edition 2.1 19 5.5 Category D: Shirts and blouses Shirts and similar items of outerwear for men, women and children that cover only the upper part of the body. Figure 1 Figure 2 Measuring point Description A - A Bust/chest circumfe

49、rence see figures 1 and 2 Measure across the width of the garment at the base of the scye, with the garment spread completely flat, and multiply by two. B - B Front tails (shaped bottom hems) see figure 1 Measure at the centre front the difference between the front panel and back panel. A - C Length of side seam see figure 1 Measure along the side seam from the base of the scye to the outer edge of the bottom hem. SANS 10188:2008 Edition 2.1 20 Figure 3 Figure 4 Measuring point Description D - D Back width (plain back) see figure 3 Measure across the