SAE J 759-2017 Lighting Identification Code.pdf

《SAE J 759-2017 Lighting Identification Code.pdf》由会员分享，可在线阅读，更多相关《SAE J 759-2017 Lighting Identification Code.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、 _ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising ther

2、efrom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2017 SAE International All rights reserved. No part of this

3、publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-49

4、70 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/J759_201712 SURFACE VEHICLE RECOMMENDED PRACTICE J759 DEC2017 Issued 1960-11 Revised 2017-12 S

5、uperseding J759 APR2014 Lighting Identification Code RATIONALE Updated document references in 2.1.2. Added new column in Table 1 for reference to J-document standards for lighting identification codes. Modified descriptor for lighting identification codes A2, A3, A4, A5, A6, and A7 in Table 1. Added

6、 lighting identification code B to Table 1 for front decorative lamp. Modified descriptor for lighting identification codes DRL, E in Table 1. Modified descriptor for lighting identification code G in Table 1 to rear facing cargo lamp. Added lighting identification code G2 to Table 1 for side facing

7、 cargo lamp. Modified descriptor for lighting identification codes J1690, M, N in Table 1. Added lighting identification codes OHV-1, OVH-2 in Table 1. Removed lighting identification codes QD1, QD2, QE1, QE2 in Table 1 as these codes were never implemented. Modified descriptor for lighting identifi

8、cation codes P, U (was U2), and U3 in Table 1. Added lighting identification code XADB to Table 1 for adaptive driving beam lamp. 1. SCOPE This SAE Recommended Practice provides the lighting function identification codes for use on all passenger vehicles, trucks, trailers, motorcycles, and emergency

9、 vehicles. 2. REFERENCES 2.1 Applicable Documents The following publications form a part of this specification to the extent specified herein. Unless otherwise indicated, the latest issue of SAE publications shall apply. SAE INTERNATIONAL J759 Proposed Draft NOV2017 Page 2 of 6 2.1.1 SAE Publication

10、s Available from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or +1 724-776-4970 (outside USA), www.sae.org. SAE J1690 Flashers 2.1.2 Federal Publications Available from the Superintendent of Documents, U. S. Government Printing Offi

11、ce, Mail Stop: SSOP, Washington, DC 20402-9320 or at: http:/www.gpo.gov/fdsys/browse/collectionCfr.action?collectionCode=CFR. CFR Title 49 Part 571.108 Lamps, Reflective Devices and Associated Equipment (FMVSS 108) Available from Transport Canada, Roads Safety and Motor Vehicle Regulation, Ottawa, O

12、ntario K1A 0N5, Canada, http:/www.tc.gc.ca/eng/acts-regulations/regulations-crc-c1038.htm. CMVSS 108 Lighting Systems and Retroreflective Devices 3. DEFINITIONS 3.1 LIGHTING IDENTIFICATION CODE A lighting identification code is a series of standardized markings for lighting devices which a manufactu

13、rer may use to mark their product to indicate the SAE Lighting Specification or Specifications to which the device is designed. Devices shall be marked for the SAE standard(s) that the device is designed to meet. The code is not intended to limit the manufacturer or supplier in applying other markin

14、gs to the devices. NOTE: SAE does not approve products; hence, the use of markings in accordance with this code should not be interpreted to mean that a device so marked has SAE approval. 4. REQUIREMENTS 4.1 Code Location The identification code should be permanently marked on the lamp where it can

15、be observed with the device mounted on the vehicle. The manufacturers identification may be located in a different area of the lamp and not required to be located in sequence with the identification code and need not be observable with the device mounted on the vehicle. Turn signal switches, hazard

16、warning switches, and flashers may have the markings located where they can be observed by removing other parts if these devices are not visible as installed on the vehicle. The manufacturers identification and model designation or part number is required on both the housing and lens of separable de

17、vices. 4.2 Size of Markings Identification numerals and letters shall be at least 3 mm high, except that markings 2 mm high may be used on lenses containing less than 12.5 cm2 of area. SAE INTERNATIONAL J759 Proposed Draft NOV2017 Page 3 of 6 4.3 Flashers Flashers, because of their small size, may u

18、se 2 mm high markings and these may be permanently stamped, etched, or lettered in indelible ink. The markings required on flashers are: a. The manufacturers identification and model number (or part number) b. The appropriate SAE Specification c. Class designation d. Application e. Ampere load ratin

19、g EXAMPLE: Flasher Incorporated SAE J1690 - Class A turn signal flasher xx amperes 4.4 Multiple Lamp Arrangements or Lamp Size Lamp size (defined by effective projected luminous area) or individual lamps designed to use more than one lamp to comply with the appropriate SAE requirements shall be mark

20、ed to indicate the number of lamps that are to be operated together or lamp size to meet this requirement. Lamps which do not carry a number within a circle or parentheses to indicate that more than one lamp is to be used are intended to be used alone unless exceptions are noted in the appropriate S

21、AE Specification. See example in Section 5. 4.5 Content of Identification Code The identification code should consist of a series of letters and numbers in the following sequence: 4.5.1 SAE 4.5.2 A number within a circle or parentheses indicating the number of separate lamps or lamp size needed to s

22、atisfy the requirements of the applicable SAE Specification. The number shall precede the function letter it refers to. No number is required for a single lamp or lamp size 1. 4.5.3 One or more letters identifying the function or functions for which the device was designed. Multipurpose devices shal

23、l be marked to cover each function for which the device was originally designed. Such devices may be used to carry out one or more of these functions. Table 1 lists the identifying designations for SAE Specifications. 4.5.4 The last two numbers of a year which means that the code letters refer to ei

24、ther: The vehicle model year of first introduction for a unique lamp designed for a specific vehicle. The calendar year of certification for a universal lamp designed for multiple vehicle use. 4.5.5 The vehicle or lamp manufacturers lettered identification or trademark and vehicle model designation

25、or part number. The manufacturers identification does not need to be located in sequence with the identification code markings but may be located in a different area of the lamp. To denote that a function meets the requirements of FMVSS 108, but not the current SAE Specification, a dash line may be

26、placed under the function letter. Example: AIRST 10. Devices marked prior to the adoption of this SAE Specification need not be remarked. SAE INTERNATIONAL J759 Proposed Draft NOV2017 Page 4 of 6 Table 1 - Lighting identification code and device description CODE REFERENCE DESCRIPTION A J594 Reflex r

27、eflector A2 J2041 Reflex reflector for use on vehicles 2032 mm or more in overall width Type 2 A3 J2041 Reflex reflector for use on vehicles 2032 mm or more in overall width Type 3 A4 J1967 Reflex reflector for vehicle conspicuity (vehicles 2032 mm width) - 50 mm wide truck/trailer A5 J1967 Reflex r

28、eflector for vehicle conspicuity (vehicles 2032 mm width) - 75 mm wide truck/trailer A6 J1967 Reflex reflector for vehicle conspicuity (vehicles 2032 mm width) - 100 mm wide truck/trailer A7 J1967 Reflex reflector for vehicle conspicuity (vehicles 2032 mm width) - 25 mm wide school bus B J3098 Front

29、 decorative lamp C J1306, J2838 Motorcycle auxiliary front lamp or the low beam portion of a headlamp used in an adaptive forward lighting system (AFS) if preceded by the letter X D J131 Motorcycle and motor-driven cycle turn signal lamp DL J2282 Distributed lighting system (headlamp) DRL J2087 Dayt

30、ime running lamp E J2039, J2838 Side turn signal lamp for use on vehicles 12m or more in length or the highway mode function in an adaptive forward lighting system (AFS) if preceded by the letter X E2 J914 Side turn signal lamp - vehicles less than 12 m in length E3 J914 Rear facing side turn signal

31、 lamp E4 J914 Side facing side turn signal lamp E5 J914 Side direction indicator lamp EVS1 J1849 Siren - interior location EVS2 J1849 Siren - exterior location EVS3 J1849 Siren - under hood location F J583 Front fog lamp F2 J1319 Rear fog lamp F3 J583 Harmonized front fog lamp G J1424 Rear facing ca

32、rgo lamp G2 J1424 Side facing cargo lamp H J2595 Sealed beam headlamp HC J2111 Headlamp cleaner HG J2009 Discharge forward lighting headlamp HH J2595 Sealed beam headlamp housing HI J1383 Integral beam headlamp HR J1383 Replaceable bulb headlamp (filament type) HL J2650 Light Emitting Diode (LED) he

33、adlamp H”x”1 J1735 Harmonized headlamp type designation (example: HR1) I J588 Rear mounted turn signal lamp or front mounted turn signal lamp mounted 100 mm or more from the headlamp; for use on vehicles 2032 mm or less in overall width I3 J588 Turn signal lamp spaced from 75 mm to less than 100 mm

34、from headlamp (1.5 times intensity values) I4 J588 Turn signal lamp spaced from 60 mm to less than 75 mm from headlamp (2 times intensity values) I5 J588 Turn signal lamp spaced less than 60 mm from headlamp (2.5 times intensity values) I6 J2261 Rear mounted turn signal lamp or front mounted turn si

35、gnal lamp mounted 100 mm or more from the headlamp; for use on vehicles 2032 mm or more in overall width I7 J2261 Front mounted turn signal lamp mounted less than 100 mm from the headlamp, for use on vehicles 2032 mm or more in overall width J1690 J1690 Flasher (types turn signal; hazard warning sig

36、nal; warning lamp alternating; combination) K J852 Front cornering lamp K2 J1373 Rear cornering lamp L J587 License plate lamp SAE INTERNATIONAL J759 Proposed Draft NOV2017 Page 5 of 6 Table 1 - Lighting identification code and device description (continued) CODE REFERENCE DESCRIPTION M J584 Motorcy

37、cle headlamp subclass H N J584 Motorcycle headlamp subclass L O J591 Spot lamp OHV-1 J1623 Off-highway vehicle headlamp Class 1 OHV-2 J1623 Off-highway vehicle headlamp Class 2 P J222 Front position lamp P2 J592 Sidemarker lamp for use on vehicles 2032 mm or less in overall width P3 J2042 Clearance,

38、 sidemarker, and identification lamp for use on vehicles 2032 mm or more in overall width PC2 J2042 Combination clearance and sidemarker lamp for use on vehicles 2032 mm or more in overall width Q J589 Turn signal operating unit - Class A QB J589 Turn signal operating unit - Class B QC J910 Vehicula

39、r hazard warning signal operating unit R J593, J2838 Reversing (back-up) lamp or the driving mode function in an adaptive forward lighting system (AFS) if preceded by the letter X S J586 Stop lamp S2 J2261 Stop lamp for use on vehicles 2032 mm or more in overall width T J585, J2591 Tail lamp (rear p

40、osition lamp) or the bending mode function in an adaptive forward lighting system (AFS) if preceded by the letter X T2 J2040 Tail lamp (rear position lamp) for use on vehicles 2032 mm or more in overall width U J1432 Rear high mounted stop lamp for use on vehicles 2032 mm or more in overall width U3

41、 J1957 Center high mounted stop lamp for use on vehicles 2032 mm or less in overall width V J2838 Town mode function in an adaptive forward lighting system (AFS) if preceded by the letter x W J2838 Weather mode function in an adaptive forward lighting system (AFS) if preceded by the letter x W-1 J59

42、5 Directional warning device - Class 1 W-2 J595 Directional warning device - Class 2 W-3 J595 Directional warning device - Class 3 W2 J887 Warning lamp for school buses W3-1 J845 Omnidirectional warning device - Class 1A W3-2 J845 Omnidirectional warning device - Class 2A W3-3 J845 Omnidirectional w

43、arning device - Class 3A WS3-1 J845 Selective coverage warning device - Class 1S WS3-2 J845 Selective coverage warning device - Class 2S WS3-3 J845 Selective coverage warning device - Class 3S W4 J774 Emergency warning device triangular shape W6 J1133 School bus stop arm lamp X J2591, J2838 Adaptive

44、 forward lighting system - used as a delineator for AFS type systems with codes C, E, R, T, V or W XADB J3069 Adaptive driving beam lamp Y J581 Auxiliary high beam lamp SAE INTERNATIONAL J759 Proposed Draft NOV2017 Page 6 of 6 5. EXAMPLES Examples of code and manufacturers identification markings: S

45、AE AIST 10 XYZ Corp. 400 Translated, this means SAE specifications for reflex reflector, turn signal lamp, stop lamp and tail lamp, current in 2010 or 2010 being the vehicle model year of first introduction of this device. The manufacturer is the XYZ Corp. (the word corporation is shown for example

46、only, since this is generally not used) and their model number is Model 400. SAE A (2) I (2) S (3) T 10 Translated, this means a size three (3) lamp area designation or effective projected luminous area (EPLA) size 3, with two (2) of the areas needed to meet the stop and turn signal requirements or

47、EPLA size 2 and three (3) of the areas needed to meet the tail lamp requirements or EPLA size 3. If, for example, each of the areas individually complied with the tail lamp requirements, the “3” preceding the letter “T” would be omitted. This would signify that all of the areas were not necessary to

48、 meet the tail lamp requirement and that each individual area meets the single function requirement. For size designation, the number corresponding to lamp area is used. If the SAE Specifications referenced in the examples were not revised and would still be current in the year 2011, for example, th

49、e manufacturer could change the marking on this device to 11, if he so desired. This coding change regarding the year might also be made if the SAE specifications have been revised in the interim and the device meets the new requirements. 6. NOTES 6.1 Revision Indicator A change bar (I) located in the left margin is for the convenience of the user in locating areas where technical revis