SAE J 246-2012 Spherical and Flanged Sleeve (Compression) Tube Fittings《球形和法兰式套筒(压缩)管配件》.pdf
《SAE J 246-2012 Spherical and Flanged Sleeve (Compression) Tube Fittings《球形和法兰式套筒(压缩)管配件》.pdf》由会员分享,可在线阅读,更多相关《SAE J 246-2012 Spherical and Flanged Sleeve (Compression) Tube Fittings《球形和法兰式套筒(压缩)管配件》.pdf(24页珍藏版)》请在麦多课文档分享上搜索。
1、 _ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising ther
2、efrom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2017 SAE International All rights reserved. No part of this
3、publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-49
4、70 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/J246_201711 SURFACE VEHICLE STANDARD J246 NOV2017 Issued 1971-05 Revised 2012-10 Reaffirmed 20
5、17-11 Superseding J246 OCT2012 Spherical and Flanged Sleeve (Compression) Tube Fittings RATIONALE J246 has been reaffirmed to comply with the SAE Five-Year Review policy. 1. SCOPE This SAE Standard covers complete general and dimensional specifications for tube fittings of the spherical and flanged
6、sleeve compression types for use in the piping of air brake systems on automotive vehicles. The spherical sleeve compression type Figures 1A to 5 and Tables 1 to 3 is intended for use with annealed copper alloy tubing per SAE J1149, Type 1. The flanged sleeve compression type Figures 6A to 11 and Ta
7、bles 4 to 6 is intended for use with nylon tubing per SAE J844. It is not intended to restrict or preclude other designs of a tube fitting for use with SAE J844, air brake tubing. Performance requirements for SAE J844 are covered in SAE J1131. See SAE J1131 for the Performance Requirements of Reusab
8、le (Push to Connect) Fittings Intended for Use in Automotive Air Brake Systems. CAUTION: To assure satisfactory performance, tapered sleeve compression type fitting components (SAE J512) should not be intermixed with the spherical or flanged sleeve components, nor should the spherical sleeve compres
9、sion type components be intermixed with the flanged sleeve compression type components when assembling connection in areas where the three types are available. 2. REFERENCES 2.1 Applicable Documents The following publications form a part of this specification to the extent specified herein. Unless o
10、therwise indicated, the latest issue of SAE publications shall apply. 2.1.1 SAE Publications Available from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or 724-776-4970 (outside USA), www.sae.org. SAE J476 Dryseal Pipe Threads SAE J5
11、12 Automotive Tube Fittings SAE J844 Nonmetallic Air Brake System Tubing SAE J846 Coding Systems for Identification of Fluid Conductors and Connectors SAE J1131 Performance Requirements for SAE J844 Nonmetallic Tubing and Fitting Assemblies Used in Automotive Air Brake Systems SAE J1149 Metallic Air
12、 Brake System Tubing and Pipe 2.1.2 ANSI Publication Available from American National Standards Institute, 25 West 43rd Street, New York, NY 10036-8002, Tel: 212-642-4900, www.ansi.org. ANSI/ASME B1.1-1989 Unified Inch Screw Thread (UN and UNR) 2.1.3 ASTM Publications Available from ASTM Internation
13、al, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, Tel: 610-832-9585, www.astm.org ASTM B 117 Method of Salt Spray (Fog) Testing FMVSS 106 Brake Hoses SAE INTERNATIONAL J246 NOV2017 Page 2 of 24_ TABLE 1A - DIMENSIONS OF CONNECTORS, UNIONS, ELBOWS, AND TEES (FIGURES 1A TO 3E
14、) Nom Tube OD, in Aa Dryseal Taper Thread in B, Nom Thread Size, in Class 2A Ext. C Nom, in C1Nom, in C2Nom, in Df Dia Drillmm Df Dia Drillin D1f Dia Maxmm D1f Dia Maxin E Dia mm+0.100.00 E Dia in +0.004 0.000 F Dia mm +0.10 0.00 F Dia in +0.0040.000 Gb Dia mm+0.000.25 Gb Dia in +0.0000.010 1/4 1/8
15、7/16-24 7/16 7/16 9/16 4.78 0.188 5.66 0.223 6.45 0.254 7.90 0.311 9.96 0.392 5/16 1/8 1/2 -24 1/2 1/2 9/16 6.35 0.250 5.66 0.223 8.08 0.318 9.60 0.378 9.96 0.454 3/8 1/4 17/32-24 9/16 9/16 11/16 7.92 0.312 8.07 0.318 9.70 0.382 11.38 0.448 12.34 0.486 1/2 3/8 11/16-20 11/16 11/16 7/8 10.31 0.406 11
16、.28 0.444 12.88 0.507 14.66 0.577 16.08 0.633 5/8 1/2 13/16-18 7/8 13/16 1- 1/16 13.49 0.531 14.42 0.568 16.05 0.632 18.01 0.709 19.10 0.752 3/4 1/2 1 -18 1 1 1- 1/16 16.66 0.656 14.42 0.568 19.25 0.758 21.59 0.850 23.85 0.939 3/4 3/4 1 -18 1- 1/16 1- 1/4 1- 1/4 16.66 0.656 19.20 0.756 19.25 0.758 2
17、1.59 0.850 23.85 0.939 1 1 1- 1/4 -16 1- 3/8 1- 1/4 1- 5/8 22.22 0.875 24.00 0.945 25.60 1.008 28.50 1.122 30.02 1.182 Nom Tube OD, in Ic mm Ic in J Full Thread Min mm J Full Thread Min in K mm K in L mm0.8 L in 0.03 L1mm0.8 L1in 0.03 L2mm0.8 L2in 0.03 M mm 0.8 M in 0.03 M1mm0.8 M1in 0.03 1/4 8.4 0.
18、33 6.9 0.27 6.4 0.25 22.9 0.90 21.6 0.85 21.6 0.85 16.0 0.63 17.8 0.70 5/16 8.6 0.34 7.1 0.28 7.1 0.28 23.9 0.94 22.9 0.90 21.8 0.86 17.0 0.67 17.8 0.70 3/8 11.2 0.44 9.7 0.38 7.9 0.31 31.0 1.22 27.9 1.10 30.2 1.19 20.3 0.80 22.9 0.90 1/2 13.5 0.53 11.2 0.44 11.2 0.44 34.0 1.34 33.3 1.31 32.5 1.28 2
19、3.9 0.94 26.4 1.04 5/8 15.0 0.59 12.7 0.50 11.2 0.44 40.4 1.59 36.3 1.43 38.4 1.51 27.9 1.10 30.5 1.20 3/4 16.8 0.66 13.5 0.53 14.2 0.56 42.9 1.69 40.6 1.60 40.1 1.58 30.5 1.20 31.2 1.23 3/4 16.8 0.66 13.5 0.53 14.2 0.56 43.7 1.72 41.4 1.63 32.5 1.28 34.5 1.36 1 18.3 0.72 15.0 0.59 19.8 0.78 50.8 2.
20、00 45.2 1.78 48.5 1.91 36.6 1.44 40.4 1.59 Nom Tube OD, in M2mm 0.8 M2in 0.03 M3mm 0.8 M3in 0.03 N mm 0.8 N in 0.03 N1mm0.8 N1in 0.03 N2mm0.8 N2in 0.03 P ref mm P ref in P1 ref mm P1 ref in S Maxmm S Maxin S1Maxmm S1Maxin 1/4 12.7 0.50 16.0 0.63 17.0 0.67 13.7 0.54 16.3 0.64 9.7 0.38 9.7 0.38 10.9 0
21、.43 5/16 13.7 0.54 17.0 0.67 17.8 0.70 14.5 0.57 16.3 0.64 9.7 0.38 9.7 0.38 11.4 0.45 - - 3/8 18.3 0.72 20.3 0.80 23.6 0.93 19.8 0.78 21.8 0.86 14.2 0.56 14.2 0.56 17.0 0.67 1/2 21.6 0.85 23.9 0.94 25.4 1.00 21.1 0.83 24.1 0.95 14.2 0.56 14.2 0.56 - 17.0 0.67 5/8 23.9 0.94 27.9 1.10 31.8 1.25 27.4
22、1.08 29.7 1.17 19.1 0.75 19.1 0.75 21.8 0.86 3/4 28.4 1.12 31.8 1.25 34.0 1.34 29.0 1.14 30.5 1.20 19.1 0.75 19.1 0.75 20.3 0.80 - - 3/4 30.5 1.20 34.0 1.34 29.0 1.14 30.5 1.20 19.1 0.75 19.1 0.75 - - 21.8 0.86 1 32.3 1.27 36.6 1.44 42.2 1.66 36.6 1.44 37.6 1.48 23.9 0.94 23.9 0.94 26.9 1.06 Continu
23、ed on next page. SAE INTERNATIONAL J246 NOV2017 Page 3 of 24_ TABLE 1A - DIMENSIONS OF CONNECTORS, UNIONS, ELBOWS, AND TEES (FIGURES 1A TO 3E) (CONTINUED) Nom Tube OD, in S2 Min mm S2 Min in S3 Min mm S3 Min in TdRef mm TdRef in T1Min mm T1Min in V Dia Max mm V Dia Max in V Dia Min mm V Dia Min in W
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- SAEJ2462012SPHERICALANDFLANGEDSLEEVECOMPRESSIONTUBEFITTINGS 球形 法兰 套筒 压缩 配件 PDF

链接地址:http://www.mydoc123.com/p-1026948.html