SAE J 1432-2010 Rear High Mounted Stop Lamps and Rear High Mounted Turn Signal Lamps for Use on Vehicles 2032 mm or More in Overall Width《总体宽度等于或超过2032mm的车辆中使用的背面高安装的停止灯和背面高安装的转弯.pdf

《SAE J 1432-2010 Rear High Mounted Stop Lamps and Rear High Mounted Turn Signal Lamps for Use on Vehicles 2032 mm or More in Overall Width《总体宽度等于或超过2032mm的车辆中使用的背面高安装的停止灯和背面高安装的转弯.pdf》由会员分享，可在线阅读，更多相关《SAE J 1432-2010 Rear High Mounted Stop Lamps and Rear High Mounted Turn Signal Lamps for Use on Vehicles 2032 mm or More in Overall Width《总体宽度等于或超过2032mm的车辆中使用的背面高安装的停止灯和背面高安装的转弯.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、 _ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising ther

2、efrom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2016 SAE International All rights reserved. No part of this

3、publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-49

4、70 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/J1432_201601 SURFACE VEHICLE RECOMMENDED PRACTICE J1432 JAN2016 Issued 1988-10 R

5、evised 2010-05 Reaffirmed 2016-01 Superseding J1432 MAY2010 Rear High Mounted Stop Lamps and Rear High Mounted Turn Signal Lamps for Use on Vehicles 2032 mm or More in Overall Width RATIONALE J1432 has been reaffirmed to comply with the SAE five-year review policy. SAE INTERNATIONAL J1432 JAN2016 Pa

6、ge 2 of 9 1. SCOPE This SAE Recommended Practice provides test procedures, requirements, and guidelines for high-mounted stop lamps and high-mounted turn signal lamps intended for use on vehicles 2032 mm or more in overall width. This document applies to trucks, motor coaches, van type trailers, and

7、 other vehicles with permanent structure greater than 2800 mm high. This document does not apply to school buses, truck tractors, pole trailers, flat-bed trailers, pick-up truck with dual wheels and trailer converter dollies. The purpose of the high-mounted stop lamp(s) and high-mounted turn signal

8、lamp(s) is to provide a signal over intervening vehicles to the driver of following vehicles. 2. REFERENCES 2.1 Applicable Publications The following publications form a part of this specification to the extent specified herein. Unless otherwise indicated, the latest issue of SAE publications shall

9、apply. 2.1.1 SAE Publications Available from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or 724-776-4970 (outside USA), www.sae.org. SAE J387 TerminologyMotor Vehicle Lighting SAE J576 Plastic Material or Materials for Use in Optica

10、l Parts Such as Lenses and Reflex Reflectors of Motor Vehicle Lighting Devices SAE J578 Color Specification SAE J759 Lighting Identification Code SAE J1889 L.E.D. Signal and Marking Lighting Devices SAE J2139 Tests for Signal and Marking Devices Used on Vehicles 2032 mm or More in Overall Width SAE

11、J2261 Stop Lamps and Front- and Rear-Turn Signal Lamps for Use on Motor Vehicles 2032 mm or More in Overall Width 2.2 Related Publications The following publications are provided for information purposes only and are not a required part of this SAE Technical Report. 2.2.1 SAE Publications Available

12、from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or 724-776-4970 (outside USA), www.sae.org. SAE J567 Lamp Bulb Retention System SAE J1957 Center High Mounted Stop Lamp Standard for Vehicles Less than 2032 mm in Overall Width SAE J2

13、577 Heavy Duty Lamp Electrical Connector Standard SAE INTERNATIONAL J1432 JAN2016 Page 3 of 9 2.2.2 Canadian Federal Publications Available from Transport Canada, Motor Vehicle Standards and Research Branch, 330 Sparks Street, Ottawa, Ontario K1A 0N5, Canada, Tel: 613-990-2309, www.tc.gc.ca. Canadia

14、n Motor Vehicle Safety Standard-108 (CMVSS-108) 2.2.3 FMVSS Publications Available from the Superintendent of Documents, U.S. Government Printing Office, Mail Stop: SSOP, Washington, DC 20402-9320. Federal Motor Vehicle Safety Standard 49 CFR 571.108 Federal Motor Carrier Safety Administration 49 CF

15、R PART 393 Subpart B 2.2.4 TMC and TTMA Publications Available from the Truck Trailer Manufacturers Association 1020 Princess Street, Alexandria, VA 22314-2247, Tel: 703- 838-1700, http:/www.ttmanet.org/publications.html. TTMA #RP-9 Location of Lighting Devices for Trailers Available from the Techno

16、logy and Maintenance Council, American Trucking Associations, 950 North Glebe Road, Suite 210, Arlington, VA 22203-4181, Tel: (703) 838-1700, . TMC #RP-702A Trailer Lamp and Reflector Placement 3. DEFINITIONS 3.1 High-Mounted Stop Lamp (HMSL) A lamp supplemental to the required Stop Lamp as describe

17、d in SAE J2261 and defined in SAE J387 but is mounted at any distance above the required Stop Lamp. 3.2 High-Mounted Turn Signal Lamp (HMTSL) A lamp supplemental to the required Turn Signal Lamp as described in SAE J2261 and defined in SAE J387 but is mounted at any distance above the required Turn

18、Signal Lamp. 3.3 The terminology contained in SAE J387 shall apply to this standard. 4. LIGHTING IDENTIFICATION CODE High-mounted stop lamps and high-mounted turn signal lamps for use on vehicles 2032 mm or more in overall width may be identified by the code U in accordance with SAE J759. SAE INTERN

19、ATIONAL J1432 JAN2016 Page 4 of 9 5. TESTS 5.1 The device shall be tested according to the procedures specified in SAE J2139. The following tests are applicable with modification as indicated. 5.1.1 Vibration 5.1.2 Moisture 5.1.3 Dust 5.1.4 Corrosion 5.1.5 Warpage Test 5.1.6 Photometry 5.1.6.1 Photo

20、metric measurement shall be made with the light source of the device at least 3 m from the photometer. The H-V axis of the device shall be taken parallel to the longitudinal axis of the vehicle. Photometric measurements shall be made with the light source steady burning. 5.1.6.2 Photometric measurem

21、ents of lamps with LED light sources should use the photometry procedure described in SAE J1889 section 5.1.5 5.2 Color SAE J578 is a part of this document. 5.3 Plastic Materials SAE J576 is a part of this document. 5.4 Dock Pad Heat Test 5.4.1 The lamp shall have its light emitting lens surface pre

22、ssed into a vinyl covered (PVC) cushion so that the light emitting surface is fully enveloped by the vinyl cover. The cushion shall consist of a pure vinyl (PVC) covering over padding consisting of 20 lb density urethane foam, 6 inches thick. 5.4.2 The lamp shall be positioned in the normal mounting

23、 position as used on the vehicle. 5.4.3 All light sources of the lamp shall be powered for the duration of the test. The lamp(s) shall be operated at 12.8 V for a 12-V system; and 25.6 V for a 24-V system. 5.4.4 The test shall be conducted at an ambient temperature of 22 C 3 C. 5.4.5 The duration of

24、 the test shall be 1 h. SAE INTERNATIONAL J1432 JAN2016 Page 5 of 9 6. REQUIREMENTS 6.1 Performance Requirements The device when tested in accordance with the test procedures of this document shall meet the requirements of SAE J2139 or as indicated. 6.1.1 Vibration 6.1.2 Moisture 6.1.3 Dust 6.1.4 Co

25、rrosion 6.1.5 Warpage Upon completion of the test, the device shall be visually examined for warpage of plastic components. If warpage is observed that could result in failure of other tests contained in this document, the test(s) shall be performed on the warped sample to ensure compliance. 6.1.6 P

26、hotometry 6.1.6.1 The lamp shall be designed to conform to the zone total photometric requirements of Figures 1 for red lamps or Figure 2 for yellow lamps including footnotes. The summation of the luminous intensity measurements at the test points in a zone shall be at least the value shown. 6.1.6.1

27、.1 A HMSL and/or HMTSL combined with a clearance lamp shall have an intensity not less than three times the luminous intensity of the clearance lamp at any test point, except that at H-V, H-5L, H-5R, 5U-V, and 5D-V, the combined lamps intensity shall be not less than five times the luminous intensit

28、y of the clearance lamp. 6.1.6.1.2 When the maximum intensity of the clearance lamp is located below the horizontal and is within an area generated by a 1.0 degree radius around a test point, the ratio for the test point may be computed using the lowest value of the clearance lamps luminous intensit

29、y within the generated area. 6.1.6.1.3 A HMSL combined with identification lamp(s) shall have an intensity not less than three times the luminous intensity of the identification lamp at any test point, except that at H-V, H-5L, H-5R, 5U-V, and 5D-V, the combined lamps intensity shall be not less tha

30、n five times the luminous intensity of the identification lamp. 6.1.6.1.4 When the maximum intensity of the identification lamp is located below the horizontal and is within an area generated by a 1.0 degree radius around a test point, the ratio for the test point may be computed using the lowest va

31、lue of the identification lamp(s) luminous intensity within the generated area. 6.1.6.2 Conformance of lamps with LED light sources should use the photometry procedure described in SAE J1889 section 6.1.5 SAE INTERNATIONAL J1432 JAN2016 Page 6 of 9 FIGURE 1 - PHOTOMETRIC REQUIREMENTS (RED) MINIMUM L

32、UMINOUS INTENSITY (cd) SAE INTERNATIONAL J1432 JAN2016 Page 7 of 9 FIGURE 2 - PHOTOMETRIC REQUIREMENTS (YELLOW) MINIMUM LUMINOUS INTENSITY (cd) 6.2 Color The color of the light from the high-mounted stop lamp or high-mounted turn signal lamp shall be as specified in SAE J578 for the following combin

33、ations. HMSL combined with Identification lampsRed HMSL combined with clearance lampsRed HMTSL combined with clearance lamp(s)Red HMTSL mounted adjacent to the clearance lamp(s) and the required turn signal lamps are yellowYellow 6.3 Plastic Materials The plastic materials used in the optical parts

34、shall meet the requirements of SAE J576. 6.4 Dock Pad Heat Test Upon completion of the test, the device shall be visually examined for warpage of plastic components. If warpage is observed that could result in failure of other tests contained in this document, the test(s) shall be performed on the w

35、arped sample to ensure compliance. SAE INTERNATIONAL J1432 JAN2016 Page 8 of 9 6.5 Design Requirements 6.5.1 If a high-mounted stop lamp or high-mounted turn signal lamp is combined with a clearance lamp or identification lamp, and a replaceable multiple light source is used, the light source retent

36、ion system shall be designed with an indexing means so that the light source is properly indexed to avoid improper orientation of the light source. Removable light source retention systems shall have an indexing feature so that they cannot be reinserted into the lamp housing in a random position, un

37、less the lamp will perform its intended function with random light source orientation. 6.5.2 The effective projected luminous lens area, as defined in SAE J387, of a single lamp shall be at least 50 cm2. 6.6 Installation Requirements The high-mounted stop lamp or high-mounted turn signal lamp shall

38、meet the following requirements as installed on the vehicle. 6.6.1 The high-mounted stop lamp or high-mounted turn signal lamp shall not be obstructed by any part of the vehicle throughout the photometric test pattern, unless the lamp is designed to comply with all photometric requirements of Figure

39、s 1 or 2 with the obstructions considered. 6.6.2 The high-mounted stop lamp or high-mounted turn signal lamp shall be mounted so the horizontal axis is perpendicular to the longitudinal axes of the vehicle with the vehicle unladen. 6.6.3 High mounted stop lamps shall not be installed when a center h

40、igh mounted stop lamp (CHMSL) is installed. 6.6.4 High mounted stop lamps and high mounted turn signal lamps shall be mounted not less than 2800 mm above the road. 6.6.5 All stop lamps must light up simultaneously. 6.6.6 High mounted turn signal lamps and mandatory turn signal lamps on one side of a

41、 vehicle shall be switched on and off by means of one control and shall flash in phase and at the same frequency. 6.6.7 All turn signal lamps on the rear of the vehicle shall be of the same color. 7. GUIDELINES 7.1 Installation Guidelines The following guidelines apply to high-mounted stop lamps or

42、high-mounted turn signal lamps as used on the vehicle and shall not be considered part of the requirements. 7.1.1 Performance of lamps may deteriorate significantly as a result of dirt, grime, snow, and ice accumulation on the optical surfaces. Installation of the device on the vehicle should be con

43、sidered to minimize the effects of these factors. 7.1.2 Where it is expected that the device must perform in extremely severe environments, the user should specify devices specifically designed for such use. Heat buildup in the lamp should be considered in applications where the lamp(s) will be pres

44、sed into the loading dock cushions. 7.1.3 The luminous intensity of the light source may vary with applied voltage. When designing the wiring circuit for the high-mounted stop lamps, or high-mounted turn signal lamps, the wiring should be sized accordingly so that adequate power is provided for the

45、stop lamps to function without degrading the function of the antilock braking system (ABS). SAE INTERNATIONAL J1432 JAN2016 Page 9 of 9 8. NOTES 8.1 Marginal Indicia A change bar (l) located in the left margin is for the convenience of the user in locating areas where technical revisions, not editor

46、ial changes, have been made to the previous issue of this document. An (R) symbol to the left of the document title indicates a complete revision of the document, including technical revisions. Change bars and (R) are not used in original publications, nor in documents that contain editorial changes only. PREPARED BY THE SAE HEAVY-DUTY LIGHTING STANDARDS COMMITTEE AND THE SAE LIGHTING COORDINATING COMMITTEE