SAE AS 9686B-2016 BOLT MACHINE C HEXAGON HEAD DRILLED 1 HOLE PD SHANK STEEL UNS K14675 DIFFUSED NICKELCADMIUM PLATE 195 KSI MIN 2500-28 UNJF-3A.pdf

《SAE AS 9686B-2016 BOLT MACHINE C HEXAGON HEAD DRILLED 1 HOLE PD SHANK STEEL UNS K14675 DIFFUSED NICKELCADMIUM PLATE 195 KSI MIN 2500-28 UNJF-3A.pdf》由会员分享，可在线阅读，更多相关《SAE AS 9686B-2016 BOLT MACHINE C HEXAGON HEAD DRILLED 1 HOLE PD SHANK STEEL UNS K14675 DIFFUSED NICKELCADMIUM PLATE 195 KSI MIN 2500-28 UNJF-3A.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、AEROSPACE STANDARD BOLT, MACHINE HEXAGON HEAD, DRILLED, 1 HOLE, PD SHANK, STEEL, UNS K14675, DIFFUSED NICKEL- CADMIUM PLATE, 195 KSI MIN, .2500-28 UNJF-3A AS9686Copyright 2016 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transm

2、itted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE

3、WEB ADDRESS: http:/www.sae.org ISSUED1998-11 REAFFIRMED2007-06 REVISED2016-06 THIRD ANGLE PROJECTION CUSTODIAN: E-25 REV.B FEDERAL SUPPLY CLASS 5306 AS9686 SHEET 1 OF 3 REV. B PROCUREMENT SPECIFICATION: AS7459 SAE Technical StandardsBoardRulesprovidethat:“ThisreportispublishedbySAE toadvancethestate

4、oftechnicalandengineering sciences. The use of thisreport isentirelyvoluntary, andits applicability andsuitability for any particularuse, includingany patent infringement arising therefrom,is the soleresponsibility of theuser.”SAE reviewseachtechnical reportatleasteveryfiveyearsatwhichtimeitmayberev

5、ised,reaffirmed,stabilized,orcancelled. SAEinvites yourwritten comments andsuggestions.SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/$6% RATIONALE REVISE THREAD SPECIFICATION TO AS8879, ADD EDGE DISTANCE EXCEPTION FOR HEAD MAR

6、KING, UPDATE MAGNETIC PARTICLE INSPECTION REFERENCE, ADD DATUM W, DATUM U, AND POSITIONAL REQUIREMENTS FOR DRILLED HOLE, CHANGE DRILLED HOLE LOCATION (FROM BEARING FACE) TO A BASIC DIMENSION, ADD NEW EXISTING INVENTORY USE NOTE, UPDATE ANSI Y14.5M-1982 SYMBOLS, RELOCATE CADMIUM NOTICE, AND GENERAL E

7、DITORIAL REVISION. NOTICE THE INITIAL SAE PUBLICATION OF THIS DOCUMENT WAS TAKEN DIRECTLY FROM U.S. MILITARY STANDARD MS9686, NOTICE 1. THIS SAE STANDARD RETAINS THE SAME PART NUMBERS ESTABLISHED BY THE ORIGINAL MILITARY DOCUMENT. ANY REQUIREMENTS ASSOCIATED WITH QUALIFIED PRODUCTS LISTS (QPL) MAY C

8、ONTINUE TO BE MANDATORY FOR DOD CONTRACTS. REQUIREMENTS RELATING TO QPLS HAVE NOT BEEN ADOPTED BY THE SAE FOR THIS STANDARD AND ARE NOT PART OF THIS SAE DOCUMENT. FIGURE 1 BOLT AEROSPACE STANDARD AS9686 SHEET 2 OF 3 REV. B BOLT, MACHINE HEXAGON HEAD, DRILLED, 1 HOLE, PD SHANK, STEEL, UNS K14675, DIF

9、FUSED NICKEL- CADMIUM PLATE, 195 KSI MIN, .2500-28 UNJF-3A TABLE 1 PART NUMBERS AND DIMENSIONS PART NO. L K APPROX. MASS LB/100 PART NO. L K APPROX. MASS LB/100 MS9686-04 .365-.385 .079-.099 1.29 MS9686-34 2.490-2.510 1.690-1.750 3.71 MS9686-05 .428-.448 .079-.099 1.36 MS9686-35 2.615-2.635 1.815-1.

10、875 3.85 MS9686-06 .490-.510 .079-.099 1.43 MS9686-36 2.740-2.760 1.940-2.000 3.99 MS9686-07 .552-.572 .079-.099 1.50 MS9686-37 2.865-2.885 2.065-2.125 4.13 MS9686-08 .615-.635 .079-.099 1.57 MS9686-38 2.990-3.010 2.190-2.250 4.27 MS9686-09 .678-.698 .079-.099 1.64 MS9686-39 3.115-3.135 2.315-2.375

11、4.42 MS9686-10 .740-.760 .079-.099 1.71 MS9686-40 3.240-3.260 2.440-2.500 4.56 MS9686-11 .802-.822 .079-.099 1.79 MS9686-41 3.365-3.385 2.565-2.625 4.71 MS9686-12 .865-.885 .079-.125 1.86 MS9686-42 3.490-3.510 2.690-2.750 4.85 MS9686-13 .928-.948 .128-.188 1.93 MS9686-43 3.615-3.635 2.815-2.875 4.99

12、 MS9686-14 .990-1.010 .190-.250 2.00 MS9686-44 3.740-3.760 2.940-3.000 5.14 MS9686-15 1.052-1.072 .252-.312 2.07 MS9686-45 3.865-3.885 3.065-3.125 5.28 MS9686-16 1.115-1.135 .315-.375 2.14 MS9686-46 3.990-4.010 3.190-3.250 5.42 MS9686-17 1.178-1.198 .378-.438 2.22 MS9686-47 4.115-4.135 3.315-3.375 5

13、.57 MS9686-18 1.240-1.260 .440-.500 2.29 MS9686-48 4.240-4.260 3.440-3.500 5.71 MS9686-19 1.302-1.322 .502-.562 2.36 MS9686-49 4.365-4.385 3.565-3.625 5.85 MS9686-20 1.365-1.385 .565-.625 2.43 MS9686-50 4.490-4.510 3.690-3.750 6.00 MS9686-21 1.428-1.448 .628-.688 2.50 MS9686-51 4.615-4.635 3.815-3.8

14、75 6.14 MS9686-22 1.490-1.510 .690-.750 2.57 MS9686-52 4.740-4.760 3.940-4.000 6.28 MS9686-23 1.552-1.572 .752-.812 2.65 MS9686-53 4.865-4.885 4.065-4.125 6.42 MS9686-24 1.615-1.635 .815-.875 2.72 MS9686-54 4.990-5.010 4.190-4.250 6.56 MS9686-25 1.678-1.698 .878-.938 2.79 MS9686-55 5.115-5.135 4.315

15、-4.375 6.70 MS9686-26 1.740-1.760 .940-1.000 2.86 MS9686-56 5.240-5.260 4.440-4.500 6.85 MS9686-27 1.802-1.822 1.002-1.062 2.93 MS9686-57 5.365-5.385 4.565-4.625 6.99 MS9686-28 1.865-1.885 1.065-1.125 3.00 MS9686-58 5.490-5.510 4.690-4.750 7.13 MS9686-29 1.928-1.948 1.128-1.188 3.08 MS9686-59 5.615-

16、5.635 4.815-4.875 7.29 MS9686-30 1.990-2.010 1.190-1.250 3.15 MS9686-60 5.740-5.760 4.940-5.000 7.42 MS9686-31 2.115-2.135 1.315-1.375 3.29 MS9686-61 5.865-5.885 5.065-5.125 7.56 MS9686-32 2.240-2.260 1.440-1.500 3.43 MS9686-62 5.990-6.010 5.190-5.250 7.71 MS9686-33 2.365-2.385 1.565-1.625 3.57 AERO

17、SPACE STANDARD AS9686 SHEET 3 OF 3 REV. B BOLT, MACHINE HEXAGON HEAD, DRILLED, 1 HOLE, PD SHANK, STEEL, UNS K14675, DIFFUSED NICKEL- CADMIUM PLATE, 195 KSI MIN, .2500-28 UNJF-3A NOTICE THIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE Q

18、UESTIONS CONCERNING CADMIUMS USE. NOTES: /1/ FOR PART NUMBERS MS9686-04 THROUGH MS9686-18 DATUM Z SHALL REPLACE DATUM Y. 2. MATERIAL: LOW ALLOY STEEL AMS6304 (UNS K14675). 3. PROCUREMENT SPECIFICATION: AS7459. 4. FINISH: DIFFUSED NICKEL-CADMIUM PLATE AMS2416. DIMENSIONS APPLY AFTER PLATING. CONTACT

19、POINTS PERMISSIBLE. PD MAY BE REDUCED .0012 MAXIUMUM BEFORE PLATING. 5. MAGNETIC PARTICLE INSPECTION PER ASTM E1444/E1444M BEFORE PLATING. 6. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, SURFACES TO BE 125 MICROINCHES Ra. 7. BREAK SHARP EDGES .0

20、03 TO .015, UNLESS OTHERWISE SPECIFIED. 8. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M-1982 (ASME PUBLICATION). 9. DIMENSIONS IN INCHES. 10. UNLESS OTHERWISE SPECIFIED, PART INVENTORY MANUFACTURED TO PREVIOUS REVISIONS OF THE APPLICABLE DRAWING OR SPECIFICATION MAY BE PROCURED AND USED UNTIL STOCK

21、IS DEPLETED. 11. DO NOT USE UNASSIGNED PART NUMBERS. 12. REVISION INDICATOR: A CHANGE BAR (I) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE

22、LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION. ASTM IS AN ASTM INTERNATIONAL PUBLICATION.