SAE AS 91111C-2017 BOLT MACHINE C DOUBLE HEXAGON EXTENDED WASHER HEAD CLOSE TOLERANCE SHANK UNS S66286 130 KSI MIN 2500-28 UNJF-3A.pdf

《SAE AS 91111C-2017 BOLT MACHINE C DOUBLE HEXAGON EXTENDED WASHER HEAD CLOSE TOLERANCE SHANK UNS S66286 130 KSI MIN 2500-28 UNJF-3A.pdf》由会员分享，可在线阅读，更多相关《SAE AS 91111C-2017 BOLT MACHINE C DOUBLE HEXAGON EXTENDED WASHER HEAD CLOSE TOLERANCE SHANK UNS S66286 130 KSI MIN 2500-28 UNJF-3A.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、AEROSPACE STANDARDBOLT, MACHINE DOUBLE HEXAGON EXTENDEDWASHER HEAD, CLOSE TOLERANCE SHANKUNS S66286, 130 KSI MIN, .2500-28 UNJF-3AAS91111Copyright 2017 SAE InternationalAll rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by

2、any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA)Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.

3、orgISSUED1999-12REVISED 2017-01THIRD ANGLE PROJECTIONCUSTODIAN: E-25REV. CFEDERAL SUPPLY CLASS5306AS91111SHEET 1 OF 2REV.CPROCUREMENT SPECIFICATION: AS7477SAE Technical Standards BoardRules providethat:“This reportis publishedby SAE to advance thestateoftechnical andengineering sciences. The useofth

4、is reportis entirely voluntary, and its applicability and suitability for any particularuse, includingany patent infringement arising therefrom, is thesole responsibility of theuser.”SAE reviews eachtechnical reportatleastevery fiveyears at whichtime it may berevised, reaffirmed, stabilized, or canc

5、elled. SAEinvites your written commentsand suggestions.SAE values your input. To provide feedback on thisTechnical Report, please visit http:/standards.sae.org/AS91111CRATIONALEDELETE .015 MIN RADIUS AT TRANSITION OF WRENCH PAD TO BASE FLANGE, DELETE CIRCLED S SYMBOL (REGARDLESS OF FEATURE SIZE) FRO

6、M STRAIGHTNESS FCF, ADD NEW NOTE FOR USE OF EXISTING INVENTORY.NOTICETHE INITIAL SAE PUBLICATION OF THIS DOCUMENT WAS TAKEN DIRECTLY FROM U.S. MILITARY STANDARDMS9111, NOTICE 1. THIS SAE STANDARD RETAINS THE SAME PART NUMBERS ESTABLISHED BY THE ORIGINAL MILITARY DOCUMENT.ANY REQUIREMENTS ASSOCIATED

7、WITH QUALIFIED PRODUCTS LISTS (QPLS) MAY CONTINUE TO BE MANDATORY FOR DOD CONTRACTS. REQUIREMENTS RELATING TO QPLS HAVE NOT BEEN ADOPTED BY THE SAE FOR THIS STANDARD AND ARE NOT PART OF THIS SAE DOCUMENT.FIGURE 1 - BOLTAEROSPACE STANDARD AS91111SHEET 2 OF 2REV.CBOLT, MACHINE DOUBLE HEXAGON EXTENDEDW

8、ASHER HEAD, CLOSE TOLERANCE SHANKUNS S66286, 130 KSI MIN, .2500-28 UNJF-3ATABLE 1 - PART NUMBERS AND DIMENSIONSPART NO.GGRIPLLENGTHKMAXAPPROX.MASSLB/100 PART NO.GGRIPLLENGTHKMAXAPPROX.MASSLB/100MS9111-01 .115-.135 .552- .572 .206 1.51 MS9111-16 .865- .885 1.490-1.510 .956 2.78MS9111-02 .115-.135 .61

9、5- .635 .206 1.58 MS9111-17 .928- .948 1.552-1.572 1.019 2.87MS9111-03 .115-.135 .678- .698 .206 1.66 MS9111-18 .990-1.010 1.615-1.635 1.081 2.96MS9111-04 .115-.135 .740- .760 .206 1.73 MS9111-19 1.115-1.135 1.740-1.760 1.206 3.13MS9111-05 .178-.198 .802- .822 .269 1.82 MS9111-20 1.240-1.260 1.865-1

10、.885 1.331 3.31MS9111-06 .240-.260 .865- .885 .331 1.90 MS9111-21 1.365-1.385 1.990-2.010 1.456 3.48MS9111-07 .302-.322 .928- .948 .393 1.99 MS9111-22 1.490-1.510 2.115-2.135 1.581 3.66MS9111-08 .365-.385 .990-1.010 .456 2.08 MS9111-23 1.615-1.635 2.240-2.260 1.706 3.84MS9111-09 .428-.448 1.052-1.07

11、2 .519 2.17 MS9111-24 1.740-1.760 2.365-2.385 1.831 4.01MS9111-10 .490-.510 1.115-1.135 .581 2.26 MS9111-25 1.865-1.885 2.490-2.510 1.956 4.19MS9111-11 .552-.572 1.178-1.198 .643 2.34 MS9111-26 1.990-2.010 2.615-2.635 2.081 4.36MS9111-12 .615-.635 1.240-1.260 .706 2.43 MS9111-27 2.115-2.135 2.740-2.

12、760 2.206 4.54MS9111-13 .678-.698 1.302-1.322 .769 2.52 MS9111-28 2.240-2.260 2.865-2.885 2.331 4.71MS9111-14 .740-.760 1.365-1.385 .831 2.61 MS9111-29 2.365-2.385 2.990-3.010 2.456 4.89MS9111-15 .802-.822 1.428-1.448 .893 2.69NOTES1. MATERIAL: CORROSION AND HEAT RESISTANT STEEL AMS5731 (UNS S66286)

13、.2. PROCUREMENT SPECIFICATION: AS7477.3. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, SURFACES TO BE 125 MICROINCHES Ra.4. FLUORESCENT PENETRANT INSPECTION PER ASTM E1417/E1417M, TYPE 1, SENSITIVITY LEVEL 2 MINIMUM.5. BREAK SHARP EDGES .003 TO .

14、015, UNLESS OTHERWISE SPECIFIED.6. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M-1982 (ASME PUBLICATION).7. DIMENSIONS ARE IN INCHES.8. UNLESS OTHERWISE SPECIFIED, PART INVENTORY MANUFACTURED TO PREVIOUS REVISIONS OF THE APPLICABLE DRAWING OR SPECIFICATION MAY BE PROCURED AND USED UNTIL STOCK IS DEPL

15、ETED.9. DO NOT USE UNASSIGNED PART NUMBERS.10. REVISION INDICATOR: A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF TH

16、E DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS.ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION.ASTM IS AN ASTM INTERNATIONAL PUBLICATION.