SAE AS 85049 28A-2011 Connector accessories electrical backshell nonenvironmental straight shield termination category 3B (for MIL-C-83733 connectors)《3B类非环保直型屏蔽终端后壳电气连接器附件(用于MIL-C.pdf

《SAE AS 85049 28A-2011 Connector accessories electrical backshell nonenvironmental straight shield termination category 3B (for MIL-C-83733 connectors)《3B类非环保直型屏蔽终端后壳电气连接器附件(用于MIL-C.pdf》由会员分享，可在线阅读，更多相关《SAE AS 85049 28A-2011 Connector accessories electrical backshell nonenvironmental straight shield termination category 3B (for MIL-C-83733 connectors)《3B类非环保直型屏蔽终端后壳电气连接器附件(用于MIL-C.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、AEROSPACE STANDARD CONNECTOR ACCESSORIES, ELECTRICAL BACKSHELL, NONENVIRONMENTAL STRAIGHT, SHIELD TERMINATION, CATEGORY 3B (FOR MIL-C-83733 CONNECTORS) AS85049/28Copyright 2011 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or trans

2、mitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE

3、 WEB ADDRESS: http:/www.sae.org ISSUED 2000-04REAFFIRMED 2006-01 STABILIZED 2011-11THIRD ANGLE PROJECTION CUSTODIAN: AE-8C1 REV.AFEDERAL SUPPLY CLASS 5935 AS85049/28SHEET 1 OF 4REV. ASAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalanden

4、gineering sciences. Theuse ofthis report is entirely voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay bereaffirm

5、ed, revised, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS85049/28ARATIONALE DOCUMENT HAS NOT REQUIRED CHANGES SINCE THE YEAR 2000, THEREFORE THE C1 COMMITTEE HAS

6、REQUESTED THIS DOCUMENT BE STABILIZED. STABILIZED NOTICE THIS DOCUMENT HAS BEEN DECLARED “STABILIZED” BY THE (TECHNICAL COMMITTEE) AND WILL NO LONGER BE SUBJECTED TO PERIODIC REVIEWS FOR CURRENCY. USERS ARE RESPONSIBLE FOR VERIFYING REFERENCES AND CONTINUED SUITABILITY OF TECHNICAL REQUIREMENTS. NEW

7、ER TECHNOLOGY MAY EXIST. NOTICE THIS DOCUMENT HAS BEEN TAKEN DIRECTLY FROM U.S. MILITARY SPECIFICATION MIL-C-85049/28B, NOTICE 1, AMENDMENT 1, AND CONTAINS ONLY MINOR EDITORIAL AND FORMAT CHANGES REQUIRED TO BRING IT INTO CONFORMANCE WITH THE PUBLISHING REQUIREMENTS OF SAE TECHNICAL STANDARDS. THE I

8、NITIAL RELEASE OF THIS DOCUMENT IS INTENDED TO REPLACE MIL-C-85049/28B, NOTICE 1, AMENDMENT 1. ANY PART NUMBERS ESTABLISHED BY THE ORIGINAL SPECIFICATION REMAIN UNCHANGED. THE ORIGINAL MILITARY SPECIFICATION WAS ADOPTED AS AN SAE STANDARD UNDER THE PROVISIONS OF THE SAE TECHNICAL STANDARDS BOARD (TS

9、B) RULES AND REGULATIONS (TSB 001) PERTAINING TO ACCELERATED ADOPTION OF GOVERNMENT SPECIFICATIONS AND STANDARDS. TSB RULES PROVIDE FOR (A) THE PUBLICATION OF PORTIONS OF UNREVISED GOVERNMENT SPECIFICATIONS AND STANDARDS WITHOUT CONSENSUS VOTING AT THE SAE COMMITTEE LEVEL, AND (B) THE USE OF THE EXI

10、STING GOVERNMENT SPECIFICATION OR STANDARD FORMAT. UNDER DEPARTMENT OF DEFENSE POLICIES AND PROCEDURES, ANY QUALIFICATION REQUIREMENTS AND ASSOCIATED QUALIFIED PRODUCTS LISTS ARE MANDATORY FOR DOD CONTRACTS. ANY REQUIREMENT RELATING TO QUALIFIED PRODUCTS LISTS (QPLS) HAS NOT BEEN ADOPTED BY SAE AND

11、IS NOT PART OF THIS SAE TECHNICAL DOCUMENT. THE REQUIREMENTS OF ACQUIRING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS SPECIFICATION SHEET AND THE ISSUE OF THE FOLLOWING SPECIFICATION LISTED IN THAT ISSUE OF THE DEPARTMENT OF DEFENSE INDEX OF SPECIFICATION AND STANDARDS (DODISS) SPECIFIED IN T

12、HE SOLICITATION: MIL-C-85049. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS85049/28SHEET 2 OF 4 REV. A CONNECTOR ACCESSORIES, ELECTRICAL BACKSHELL, NONENVIRONMENTAL STRAIGHT, SHIELD TERMINATION, CATEGORY 3B (FOR MIL-C-83733 CO

13、NNECTORS) FIGURE 1 CONFIGURATIONS AND DIMENSIONS Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS85049/28SHEET 3 OF 4 REV. A CONNECTOR ACCESSORIES, ELECTRICAL BACKSHELL, NONENVIRONMENTAL STRAIGHT, SHIELD TERMINATION, CATEGORY 3B

14、(FOR MIL-C-83733 CONNECTORS) FIGURE 1 CONFIGURATIONS AND DIMENSIONS CONTINUED Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS85049/28SHEET 4 OF 4 REV. A CONNECTOR ACCESSORIES, ELECTRICAL BACKSHELL, NONENVIRONMENTAL STRAIGHT, SHI

15、ELD TERMINATION, CATEGORY 3B (FOR MIL-C-83733 CONNECTORS) REQUIREMENTS: DESIGN AND CONSTRUCTION: DIMENSIONS AND CONFIGURATIONS: SEE FIGURE 1. RFI GASKETS (METALASTIC AND MONEL MESH) ARE TO BE SUPPLIED AND PERFORM RFI SHIELDING FUNCTION. RFI GASKETS (METALASTIC) SHALL BE MANUFACTURED TO FIT ACCESSORY

16、 ASSEMBLY. RFI GASKET (MONEL MESH) SHALL BE MANUFACTURED TO FIT ASSOCIATED CONNECTOR RECEPTACLE SHELL. MATERIAL: SHELL - 1/ N SCREWS PASSIVATE PART NUMBER: SEE FIGURE 1. QUALIFICATION: SEE MIL-C-85049, CATEGORY 3B, CABLE PULLOUT, COUPLING THREAD STRENGTH, EXTERNAL BENDING MOMENT, AND SAFETY WIRE HOLES NOT APPLICABLE. QPL EVALUATING ACTIVITY: NAVAL AIR WARFARE CENTER, (CODE DP704N), 6000 E. 21ST ST., INDIANAPOLIS, IN 46219-2189. SUPPRESSION DATA: 1/ NOT FOR NAVY USE. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-