SAE AS 85049 148-2014 INDIVIDUAL SHIELD TERMINATION CONNECTOR ELECTRICAL (CATEGORY 9).pdf

《SAE AS 85049 148-2014 INDIVIDUAL SHIELD TERMINATION CONNECTOR ELECTRICAL (CATEGORY 9).pdf》由会员分享，可在线阅读，更多相关《SAE AS 85049 148-2014 INDIVIDUAL SHIELD TERMINATION CONNECTOR ELECTRICAL (CATEGORY 9).pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、 AEROSPACE STANDARD INDIVIDUAL SHIELD TERMINATION, CONNECTOR,ELECTRICAL (CATEGORY 9) AS85049/148Copyright 2014 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photo

2、copying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2014-09THIRD ANGLE PROJECTI

3、ON CUSTODIAN: AE-8/AE-8C1 FEDERAL SUPPLY CLASS 5935 AS85049/148 SHEET 1 OF 6 PROCUREMENT SPECIFICATION: AS85049SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineeringsciences.The useof this reportisentirelyvoluntary, andits appli

4、cability and suitability forany particular use,including any patent infringement arising therefrom, is thesole responsibility oftheuser.”SAE reviews eachtechnicalreportat least every five years at which time itmay berevised,reaffirmed, stabilized, orcancelled. SAE invites yourwrittencomments andsugg

5、estions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS85049/148RATIONALE AS85049/148 PERMITS THE CANCELLATION AND SUPERSESSION OF MS27741 WITH THIS DOCUMENT. NOTICE THE COMPLETE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIB

6、ED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS85049. FIGURE 1 - INDIVIDUAL SHIELD TERMINATION TABLE 1 - FIGURE 1 METRIC EQUIVALENTS INCHES MILLIMETERS .045 1.143.4375 11.1125AEROSPACE STANDARD AS85049/148SHEET 2 OF 6INDIVIDUAL SHIELD TERMINATION, CONNECTOR, ELECTRICAL (CATEGORY

7、9)TABLE 2 - FIGURE 1 DIMENSIONS DASH NUMBER ENTRY DIAMETER A DIA. MAX. NUMBER OF SLOTS WEIGHT IN POUNDS (GRAMS) REF. 2.250(6.350) .545(13.843) 3 .005(2.268) 3.375(9.525) .670(17.018) 4 .006(2.722) 4.500(12.700) .795(20.193) 6 .007(3.175) 5.625(15.875) .920(23.368) 8 .009(4.082) 6.750(19.050) 1.045 (

8、26.543) 10.010(4.536) 7.875(22.225) 1.170 (29.718) 10.011(4.990) 81.000 (25.400) 1.295 (32.893) 12.012(5.443) 91.125 (28.575) 1.420 (36.068) 15.014(6.350) 101.250 (31.750) 1.687 (42.850) 15.023(10.433) 111.375 (34.925) 1.812 (46.025) 15.032(14.515) REQUIREMENTS: 1. DESIGN AND CONSTRUCTION: THE SHIEL

9、D TERMINATION SHALL BE DESIGNED IN ACCORDANCE WITH FIGURE 1 AND TABLE 2. DIMENSIONS ARE IN INCHES. METRIC EQUIVALENTS ARE IN PARENTHESES, GIVEN FOR INFORMATION ONLY, AND BASED ON 1 INCH = 25.4 MILLIMETERS. UNLESS OTHERWISE SPECIFIED, TOLERANCE SHALL BE .XX .03 (0.762 MILLIMETERS) AND .XXX .015 (0.38

10、1 MILLIMETERS). ANGULAR TOLERANCES SHALL BE X 2. 2. MATERIAL: a. BODY - ALUMINUM ALLOY IN ACCORDANCE WITH ASTM B221 OR ASTM B211. b. NUT - ALUMINUM ALLOY IN ACCORDANCE WITH ASTM B221 OR ASTM B211. c. SPRING - COPPER ALLOY. d. FRICTION WASHER - TEFLON. 3. FINISH: a. BODY - GOLD CHEMICAL CONVERSION CO

11、ATING IN ACCORDANCE WITH MIL-DTL-5541, CLASS 3. b. NUT - GOLD CHEMICAL CONVERSION COATING IN ACCORDANCE WITH MIL-DTL-5541, CLASS 3. 4. SHIELD COMPENSATION: CAPTIVATED SPRING MEMBER IN CLAMP NUT COMPENSATES FOR DIFFERENCES IN SHIELD THICKNESS OF AT LEAST .020 INCH (0.508 MILLIMETER) BETWEEN ADJACENT

12、SLOTS IN BODY. 5. SHIELD ACCOMMODATION: EACH SLOT IN BODY WILL ACCOMMODATE UP TO .180 INCH (4.572 MILLIMETERS) TOTAL SHIELD THICKNESS. AEROSPACE STANDARD AS85049/148SHEET 3 OF 6INDIVIDUAL SHIELD TERMINATION, CONNECTOR, ELECTRICAL (CATEGORY 9)6. PART NUMBER: SEE EXAMPLES BELOW FOR REPLACEMENT AND NEW

13、 DESIGN APPLICATIONS. REPLACEMENT PART NUMBER: MS27741 -6 BASIC PART NUMBER DASH NUMBER NEW DESIGN PART NUMBER: M85049/148 -6 BASIC PART NUMBER DASH NUMBER APPLICATION NOTES: ASSEMBLY INSTRUCTIONS THE FOLLOWING INSTRUCTIONS ARE SUGGESTED ASSEMBLY PROCEDURES ONLY. ACTUAL TERMINATION AND ASSEMBLY METH

14、OD WILL DEPEND ON THE ACCEPTED TECHNIQUES OF THE USER. THE TERMINATION AND GROUND RING REQUIRES NO SPECIAL ASSEMBLY TOOLS AND CAN BE ASSEMBLED BY HAND. HOWEVER, THE USER MAY FIND IT PREFERABLE TO USE SOFT JAW PLIERS FOR FINAL TIGHTENING OF THE TERMINATION AND GROUND RINGS. IN ALL CASES, A SELF-PIGTA

15、ILING TECHNIQUE FOR THE INDIVIDUAL SHIELDS IS USED, WITH THE POINT AT WHICH THE CONDUCTORS ARE EXTRACTED THROUGH THE SHIELDS TO BE DETERMINED BY THE PARTICULAR CONNECTOR INVOLVED. FOR SOLDER CONTACT CONNECTORS, THE LENGTH OF THE EXTRACTED CONDUCTOR WILL BE SHORTER THAN FOR THE CRIMP CONTACT CONNECTO

16、RS. IT IS SUGGESTED THAT ALL SHIELD PIGTAILS BE FLATTENED BEFORE INSTALLING THE TERMINATION AND GROUND RING. TERMINATION AND GROUND RING: a. PLACE TERMINATION AND GROUND RING ON WIRE BUNDLE OR CABLE WITH CASTELLATED (SLOTTED) FACE OF BODY TOWARD TERMINATION END OF CABLE (SEE FIGURE 2, STEP 1). b. IF

17、 SHIELDED CONDUCTORS HAVE AN OUTER JACKET, STRIP JACKET TO DESIRED LENGTH. EXTRACT CONDUCTORS THROUGH SHIELDS AT LOCATION DESIRED FOR INSTALLATION OF THE TERMINATION AND GROUND RING. FLATTEN SHIELD PIGTAILS. FIGURE 2 - STEP 1 OF ASSEMBLY INSTRUCTIONS AEROSPACE STANDARD AS85049/148SHEET 4 OF 6INDIVID

18、UAL SHIELD TERMINATION, CONNECTOR, ELECTRICAL (CATEGORY 9)c. WITH SHIELDS HELD AGAINST WIRE BUNDLE, SEPARATE CLAMP NUT FROM BODY. FLARE SHIELDS OUTWARD, PERPENDICULAR TO THE WIRE BUNDLE (SEE STEP 1). FIGURE 3 - STEP 2 OF ASSEMBLY INSTRUCTIONS d. PLACE SHIELDS IN SLOTS OF BODY MAKING SURE SHIELDS ARE

19、 DISTRIBUTED AS UNIFORMLY AS POSSIBLE AMONG THE SLOTS (SPRING MEMBER IN CLAMP NUT WILL COMPENSATE FOR DIFFERENCES IN SHIELD THICKNESS OF AT LEAST .020 INCH (0.508 MILLIMETERS) BETWEEN ADJACENT SLOTS. IF DESIRED, SHIELDS CAN BE DOUBLED TO ACHIEVE MORE UNIFORM THICKNESS BETWEEN ADJACENT SLOTS (SEE STE

20、P 2). FIGURE 4 - STEP 3 OF ASSEMBLY INSTRUCTIONS e. INSTALL GROUND LEAD IN TWO SLOTS OF BODY BY LOOPING AROUND A BODY TAB AS SHOWN IN STEP 3. CONNECT GROUND LEAD TO SELECTED TERMINATION POINT. FIGURE 5 - STEP 4 OF ASSEMBLY INSTRUCTIONS AEROSPACE STANDARD AS85049/148SHEET 5 OF 6INDIVIDUAL SHIELD TERM

21、INATION, CONNECTOR, ELECTRICAL (CATEGORY 9)f. FOLD SHIELDS OVER KNURLED SURFACE OF BODY AND ENGAGE CLAMP NUT ALIGNING TABS OF CLAMP NUT SPRING WITH SLOTS IN BODY. TIGHTEN SECURELY AS SHOWN IN STEP 4. HAND TIGHTENING CAN BE USED, BUT IF PREFERRED, SOFT JAW PLIERS CAN BE USED FOR FINAL TIGHTENING. FIG

22、URE 6 - STEP 5 OF ASSEMBLY INSTRUCTIONS g. TRIM EXCESS SHIELDS TO DESIRED LENGTH, EITHER FLUSH WITH SURFACE OF TERMINATION AND GROUND RING OR TO ANY LENGTH DESIRED. FOR FUTURE REPAIR ABILITY, IT IS SUGGESTED AT LEAST .5 INCH (12.7 MILLIMETERS) SHIELD LENGTHS BE RETAINED (SEE STEP 5). FIGURE 7 - STEP

23、 6 OF ASSEMBLY INSTRUCTIONS h. IF DESIRED, SAFETY WIRE CAN BE INSTALLED THROUGH HOLE PROVIDED IN CLAMP NUT. SIMPLY LOOP WIRE THROUGH HOLE AND TIGHTEN AS SHOWN IN STEP 6. WITH SAFETY WIRE INSTALLED BETWEEN TWO BODY TABS, IT WORKS SIMILAR TO A COTTER PIN TO PREVENT ACCIDENTAL LOOSENING. FIGURE 8 - STE

24、P 7 OF ASSEMBLY INSTRUCTIONS AEROSPACE STANDARD AS85049/148SHEET 6 OF 6INDIVIDUAL SHIELD TERMINATION, CONNECTOR, ELECTRICAL (CATEGORY 9)i. TERMINATION AND GROUND RING CAN BE INSULATED BY INSTALLING HEAT SHRINKABLE SLEEVING OVER COMPLETED ASSEMBLY (SEE STEP 7). FIGURE 9 - STEP 8 OF ASSEMBLY INSTRUCTI

25、ONS SPECIFICATION NOTES: 1. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.