SAE AS 6383-2017 FITTING ASSEMBLY REDUCER WITH SOLID FILM LUBRICANT RING LOCKED PORT CONNECTION TO BEAM SEAL 4000 PSI AND 5000 PSI 8 .pdf

《SAE AS 6383-2017 FITTING ASSEMBLY REDUCER WITH SOLID FILM LUBRICANT RING LOCKED PORT CONNECTION TO BEAM SEAL 4000 PSI AND 5000 PSI 8 .pdf》由会员分享，可在线阅读，更多相关《SAE AS 6383-2017 FITTING ASSEMBLY REDUCER WITH SOLID FILM LUBRICANT RING LOCKED PORT CONNECTION TO BEAM SEAL 4000 PSI AND 5000 PSI 8 .pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 AEROSPACE STANDARD FITTING ASSEMBLY, REDUCER WITH SOLID FILM LUBRICANT, RING LOCKED PORT CONNECTION TO BEAM SEAL 4000 PSI AND 5000 PSI /8/ AS6383Copyright 2017 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any f

2、orm or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: ht

3、tp:/www.sae.org ISSUED2017-03THIRD ANGLE PROJECTION CUSTODIAN: G-3/G-3B FEDERAL SUPPLY CLASS 4730 AS6383 SHEET 1 OF 3 PROCUREMENT SPECIFICATION: AS85720 /4/ SAE Technical StandardsBoardRulesprovidethat:“ThisreportispublishedbySAE toadvancethestateoftechnicalandengineering sciences. The use of thisre

4、port isentirelyvoluntary, andits applicability andsuitability for any particularuse, includingany patentinfringement arising therefrom,is the soleresponsibility of theuser.”SAE reviewseachtechnical reportatleasteveryfiveyearsatwhichtimeitmayberevised,reaffirmed,stabilized,orcancelled. SAEinvites you

5、rwritten comments andsuggestions.SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS6383 RATIONALE TO CREATE INDUSTRY STANDARD FOR FITTINGS SIMILAR TO AS4383, EXCEPT WITH SOLID FILM LUBRICANT. FIGURE 1 - ADAPTER, ASSEMBLY TABLE 1 TABLE 1A - DI

6、MENSIONS A THROUGH H BASIC NO. AS6306 /15/ SIZE CODE (A) THREAD AS8879 B THREAD AS8879 C D E +.000 -.015 F +.010 -.005 G H .007 05-04 .4375-24UNJS-3A .3750-24UNJF-3A .184-.190 .232 .381 .701 .624 .192 06-04 .4375-24UNJS-3A .4375-20UNJF-3A .184-190 .295 .395 .733 .700 .210 08-04 .4375-24UNJS-3A .5625

7、-18UNJF-3A .184-.190 .412 .430 .734 .814 .210 08-06 .5625-20UNJS-3A .5625-18UNJF-3A .294-.300 .412 .430 .754 .814 .210 10-04 .4375-24UNJS-3A .6875-24UNJEF-3A .184-.190 .498 .465 .758 1.040 .210 10-06 .5625-20UNJS-3A .6875-24UNJEF-3A .294-.300 .498 .465 .758 1.040 .210 10-08 .7188-20UNJS-3A .6875-24U

8、NJEF-3A .398-.408 .498 .465 .771 1.040 .210 12-06 .5625-20UNJS-3A .8125-20UNJEF-3A .294-.300 .633 .527 .751 1.170 .220 12-08 .7188-20UNJS-3A .8125-20UNJEF-3A .398-.408 .633 .527 .764 1.170 .220 12-10 .8438-18UNJS-3A .8125-20UNJEF-3A .493-.503 .633 .527 .828 1.170 .220 16-10 .8438-18UNJS-3A 1.1250-18

9、UNJEF-3A .493-.503 .861 .564 .841 1.456 .220 16-12 1.0000-16UNJ-3A 1.1250-18UNJEF-3A .604-.614 .861 .564 .881 1.456 .220 20-12 1.0000-16UNJ-3A 1.3125-18UNJEF-3A .604-.614 1.057 .569 .888 1.782 .240 20-16 1.2500-14UNJS-3A 1.3125-18UNJEF-3A .839-.851 1.057 .569 .936 1.782 .240 24-12 1.0000-16UNJ-3A 1.

10、6250-18UNJEF-3A .604-.614 1.297 .608 .909 2.031 .240 24-16 1.2500-14UNJS-3A 1.6250-18UNJEF-3A .839-.851 1.297 .608 .957 2.031 .240 (A) THREAD FITTING END PERAS85720/1 EXCEPT C(N) ( ) ( ) /7a/ 2X R.030 MIN P NO. OF SERRATIONS AEROSPACE STANDARD AS6383 SHEET 2 OF 3 FITTING ASSEMBLY, REDUCER WITH SOLID

11、 FILM LUBRICANT, RING LOCKED PORT CONNECTION TO BEAM SEAL 4000 PSI AND 5000 PSI /8/ TABLE 1B - DIMENSIONS J THROUGH P BASIC NO. AS6306 /15/ SIZE CODE (J) K +.005 -.002 L +.010 -.005 M (N) P 05-04 .377-.383 .299 .125 .393 .275 36 06-04 .377-.383 .362 .125 .456 .275 36 08-04 .377-.383 .480 .125 .574 .

12、275 40 08-06 .490-.497 .480 .125 .574 .295 40 10-04 .377-.383 .623 .125 .717 .275 38 10-06 .490-.497 .623 .125 .717 .295 38 10-08 .646-.654 .623 .125 .717 .308 38 12-06 .490-.497 .735 .157 .891 .295 40 12-08 .646-.654 .735 .157 .891 .308 40 12-10 .763-.772 .735 .157 .891 .372 40 16-10 .763-.772 .998

13、 .157 1.154 .372 36 16-12 .910-.919 .998 .157 1.154 .412 36 20-12 .910-.919 1.223 .157 1.379 .412 56 20-16 1.148-1.158 1.223 .157 1.379 .460 56 24-12 .910-.919 1.500 .157 1.656 .412 81 24-16 1.148-1.158 1.500 .157 1.656 .460 81 NOTES 1. MATERIAL: a. FITTING: 6Al-4V TITANIUM ALLOY PER AMS4928, AMS496

14、5, OR AMS4967 b. LOCKRING: A286 CORROSION RESISTANT STEEL PER AMS5731, AMS5732, AMS5734, AMS5737, OR AMS5853 2. HEAT TREATMENT: a. FITTING: 130 KSI UTS MIN b. LOCKRING: 34 TO 40 HRC 3. FINISH: a. FITTING: ANODIC TREATMENT PER AMS2488, TYPE 2. APPLY SOLID FILM LUBRICANT PER AS5272, TYPE 1, TO SEALING

15、 SURFACE OF FITTING END AS85720/1 AND “A” THREAD ONLY. OVERSPRAY ON THREAD UNDERCUT PERMISSIBLE. b. LOCKRING: PASSIVATE PER AMS2700, TYPE 2 OR 8. /4/ PROCUREMENT SPECIFICATION: a. AS85421 (/15/ PORT END SIZES 05, 20, AND 24) EXCEPT AS SPECIFIED ON THIS STANDARD: PRODUCT SUPPLIED TO THIS SPECIFICATIO

16、N SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST FOR PRI-QPL-AS85421 FOR THIS STANDARD. SEE www.eAuditN FOR CURRENT QPL ONLINE. b. AS85720 (/15/ PORT END SIZES 06, 08, 10, 12, AND 16) EXCEPT AS SPECIFIED ON THIS STANDARD:

17、PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST FOR PRI-QPL-AS85720 FOR THIS STANDARD. SEE www.eAuditN FOR CURRENT QPL ONLINE. THIS QPL REQUIREMENT SHALL BE IN EFFECT FOR PURCHASE ORDE

18、RS PLACED ON OR AFTER DECEMBER 1, 2016. SUPPLIERS SEEKING LISTING ON THE INTIAL QPL MUST APPLY TO PRI FOR APPROVAL NO LATER THAN JUNE 1, 2016. UNTIL THE QPL IS IN EFFECT, USERS OF THIS STANDARD ARE ADVISED TO CONTROL SOURCE APPROVALS. TRANSITION TO PRI-QPL SHALL BE COMPLETED BY DECEMBER 1, 2016. /5/

19、 SEALING SURFACE: NO VISIBLE DEFECTS. TO BE PROTECTED FOR SHIPMENT. AEROSPACE STANDARD AS6383 SHEET 3 OF 3 FITTING ASSEMBLY, REDUCER WITH SOLID FILM LUBRICANT, RING LOCKED PORT CONNECTION TO BEAM SEAL 4000 PSI AND 5000 PSI /8/ /6/ LOCKRING RETAINED ON FITTING BY CONTROLLED INTERFERENCE FIT. /7/ a. M

20、ARK AT LOCATION(S) SHOWN PER AS478 METHOD 2 OR 15, WITH MANUFACTURERS NAME, TRADEMARK, OR CAGE CODE. b. BAG AND TAG PER AS478 METHOD 35D, WITH MANUFACTURERS NAME, TRADEMARK OR CAGE CODE, AND PART NUMBER. /8/ WORKING PRESSURE: THIS PART IS DESIGNED FOR USE IN 5000 PSI (20000 PSI BURST PRESSURE) HYDRA

21、ULIC WORKING PRESSURE SYSTEMS COMPATIBLE WITH TITANIUM, EXCEPT PORT END SIZES 20 AND 24 ARE FOR 4000 PSI (16000 PSI BURST PRESSURE). 9. ADAPTERS TO BE INSTALLED INTO BOSS CAVITIES PER AS1300. 10. INTERPRETATION OF DRAWING PER AS4296. 11. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER AS

22、ME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 MICROINCHES Ra AND SEALING SURFACE TO BE 63 MICROINCHES Ra. 12. BREAK EDGES .003 TO .015, UNLESS OTHERWISE SPECIFIED. 13. DIMENSIONS AND TOLERANCING: ASME Y14.5M-1994. 14. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .005, ANGULAR DIMENSIONS 030 . /15/ EXAMPLE OF PART NUMBER: AS6383-16-10 BASIC PART NUMBER SIZE CODE PER AS6383 TUBE END SIDE (THREAD “A”) SIZE CODE PR AS638 PORT END SIDE (THREAD “B”)