SAE AS 6117A-2015 FITTING ASSEMBLY UNION AXIALLY SWAGED HYDRAULIC UP TO 1500 PSI.pdf

《SAE AS 6117A-2015 FITTING ASSEMBLY UNION AXIALLY SWAGED HYDRAULIC UP TO 1500 PSI.pdf》由会员分享，可在线阅读，更多相关《SAE AS 6117A-2015 FITTING ASSEMBLY UNION AXIALLY SWAGED HYDRAULIC UP TO 1500 PSI.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 AEROSPACE STANDARD FITTING ASSEMBLY, UNION, AXIALLY SWAGED, HYDRAULIC, UP TO 1500 PSI AS6117Copyright 2015 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocop

2、ying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2011-07REVISED 2015-05THIRD AN

3、GLE PROJECTION CUSTODIAN: G-3/G-3B REV.A FEDERAL SUPPLY CLASS 4730AS6117 SHEET 1 OF 3 REV. A PROCUREMENT SPECIFICATION: /4/ AS6116SAE Technical Standards Board Rules provide that: “This report ispublished by SAE toadvance thestate of technicalandengineering sciences. Theuse ofthisreport is entirelyv

4、oluntary, andits applicability and suitability forany particularuse,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed, stabilized, orcancelled. SAE invites yourwr

5、ittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS6117A RATIONALE ADDED REDUCER CONFIGURATIONS 1008, 1210, 1612, 2016, AND 2420. FIGURE 1 - FITTING ASSEMBLY, UNION AEROSPACE STANDARD AS6117 SHEET 2 O

6、F 3 REV. A FITTING ASSEMBLY, UNION, AXIALLY SWAGED, HYDRAULIC, UP TO 1500 PSI TABLE 1A - DIMENSIONS A THROUGH J BASIC NO. AS6117 /16/ SIZE CODE NOMINAL TUBE SIZE END 1 NOMINAL TUBE SIZEEND 2 A MAXA1 MAXE MAXEA MAXF MIN FA MIN J /12/ ALLOWABLETUBE GAP 0404 .250 .250 1.416 1.110 .435 .435 .253 .253 .1

7、50 .150 0505 .3125 .3125 1.676 1.380 .503 .503 .3155 .3155 .150 .150 0604 .375 .250 1.995 1.595 .580 .435 .378 .253 .300 .300 0606 .375 .375 1.974 1.520 .580 .580 .378 .378 .150 .150 0806 .500 .375 2.477 1.970 .755 .580 .503 .378 .300 .300 0808 .500 .500 2.380 1.860 .755 .755 .503 .503 .150 .150 100

8、8 .625 .500 2.770 2.274 .929 .755 .629 .503 .350 .350 1010 .625 .625 2.390 1.910 .929 .929 .629 .629 .150 .150 1210 .750 .625 2.915 2.393 1.150 .929 .754 .629 .350 .350 1212 .750 .750 2.670 2.110 1.150 1.150 .754 .754 .150 .150 1612 1.000 .750 3.425 2.769 1.474 1.150 1.004 .754 .350 .350 1616 1.000

9、1.000 3.412 2.652 1.474 1.474 1.004 1.004 .150 .150 2016 1.250 1.000 4.075 3.287 1.768 1.474 1.255 1.004 .350 .350 2020 1.250 1.250 3.960 3.120 1.768 1.768 1.255 1.255 .150 .150 2420 1.500 1.250 4.728 3.820 2.070 1.768 1.505 1.255 .350 .350 2424 1.500 1.500 4.680 3.680 2.070 2.070 1.505 1.505 .150 .

10、150 TABLE 1B - DIMENSIONS W THROUGH W3A AND WEIGHTS BASIC NO. AS6117 /16/ SIZE CODE NOMINAL TUBE SIZE END 1 NOMINAL TUBE SIZEEND 2 W MINW1 MAXW1AMAXW2.002W2A.002 W3 MAX W3A MAX WEIGHTAPPROXLB/EA 0404 .250 .250 .185 .604 .604 .320 .320 .020 .020 .008 0505 .3125 .3125 .180 .724 .724 .371 .371 .020 .02

11、0 .014 0604 .375 .250 .480 .883 .604 .463 .320 .020 .020 .018 0606 .375 .375 .195 .883 .883 .463 .463 .020 .020 .020 0806 .500 .375 .400 1.076 .883 .595 .463 .020 .020 .034 0808 .500 .500 .210 1.076 1.076 .595 .595 .020 .020 .043 1008 .625 .500 .530 1.076 1.076 .758 .595 .020 .020 .060 1010 .625 .62

12、5 .225 1.076 1.076 .758 .758 .020 .020 .057 1210 .750 .625 .550 1.201 1.076 .903 .758 .025 .020 .095 1212 .750 .750 .235 1.201 1.201 .903 .903 .025 .025 .100 1612 1.000 .750 .570 1.566 1.201 1.196 .903 .035 .025 .185 1616 1.000 1.000 .260 1.566 1.566 1.196 1.196 .035 .035 .210 2016 1.250 1.000 .605

13、1.829 1.566 1.460 1.196 .035 .035 .315 2020 1.250 1.250 .285 1.829 1.829 1.460 1.460 .035 .035 .322 2420 1.500 1.250 .700 2.178 1.829 1.704 1.460 .035 .035 .480 2424 1.500 1.500 .310 2.178 2.178 1.704 1.704 .035 .035 .552 NOTES: /1/ MATERIALS: CODE LETTER “D“ BODY - TYPE 6061-T6 ALUMINUM ALLOY BAR P

14、ER AMS-QQ-A-225/8. RING - TYPE 7075-T73 ALUMINUM ALLOY BAR PER AMS-QQ-A-225/9. 2. FINISH: BODY - CHEMICAL CONVERSION COATED PER MIL-DTL-5541 TYPE I CLASS 3. RINGS - ANODIZE PER MIL-A-8625, TYPE II, CLASS 2, DYED GREEN, SIMILAR TO NO. 14187, 14193, OR 14223 OF FED-STD-595 AND SHALL BE DUPLEX SEALED.

15、AEROSPACE STANDARD AS6117 SHEET 3 OF 3 REV. A FITTING ASSEMBLY, UNION, AXIALLY SWAGED, HYDRAULIC, UP TO 1500 PSI /3/ COATINGS/LUBRICANTS: BODY a. DRY FILM LUBRICANT PER AS5272 TYPE I SHALL BE APPLIED TO THE OD OF THE AXIALLY SWAGED FITTING END. ADDITIONAL LUBRICANT APPLIED SHALL BE SPECIFIED BY MANU

16、FACTURER. THE LUBRICANTS SHALL NOT BE IN CONTACT WITH THE SYSTEM FLUID. b. POLYTETRAFLUOROETHYLENE (PTFE) COAT, LIGHT GREEN, SHALL BE APPLIED TO PORTIONS OF ID (BORE) UP TO THE FIRST GROOVE. OVERSPRAY IN GROOVE IS NOT PERMITTED. c. A MINIMUM OF TWO GROOVES (END SIZE -05 AND LARGER) SHALL BE FILLED W

17、ITH ELASTOMERIC DIMETHYL SILOXANE COMPOUND. FOR SMALLER SIZE ENDS, A MINIMUM OF ONE GROOVE SHALL BE FILLED WITH THE COMPOUND. /4/ PROCUREMENT SPECIFICATION: AS6116 EXCEPT AS SPECIFIED ON THIS STANDARD. PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER LISTED

18、IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST (QPL) PRI-QPL-AS6116 FOR THIS STANDARD. SEE www.eAuditN FOR THE CURRENT QPL ON-LINE. 5. DIMENSIONS AND TOLERANCES NOT DEFINED ON THIS STANDARD SHALL BE SPECIFIED AND CONTROLLED BY THE MANUFACTURER. THE MANUFACTURER IS RESPONSIBLE TO E

19、NSURE COMPLIANCE WITH THE PROCUREMENT SPECIFICATION. /6/ IDENTIFICATION SHALL BE IN ACCORDANCE WITH AS6116 AND SHALL BE IDENTIFIED ON EITHER RING IN THE AREA SHOWN. FOR SIZE -05 AND LARGER, THE RING O.D. SHALL HAVE TWO GROOVES INDICATING DUAL SEALING BACK UP FEATURE. 7. FITTINGS SHALL BE INSTALLED I

20、N ACCORDANCE WITH AS6124. 8. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, THE MAXIMUM MACHINED SURFACES SHALL BE 125 MICROINCHES Ra. 9. BREAK EDGES .003 TO .010 INCHES UNLESS OTHERWISE SPECIFIED. 10. DIMENSIONING AND TOLERANCING: ASME Y14.5M-199

21、4. 11. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .015, ANGULAR DIMENSIONS 030. /12/ DIMENSION “J” IS THE ALLOWABLE TUBE END POSITIONING FOR SYSTEM LAYOUT DESIGN. /13/ FOR JUMP SIZE FITTINGS, A TRANSITION DIAMETER WILL OCCUR IN THIS AREA. /14/ DIMENSION “A” IS TH

22、E FITTING ASSEMBLY LENGTH PRIOR TO SWAGE AND “A1” IS THE AFTER SWAGE ASSEMBLY LENGTH MEASURED FROM THE SWAGED RINGS. /15/ PARTS FOR OXYGEN SYSTEMS SHALL BE IDENTIFIED IN THE PART NUMBER AS SUFFIX CODE “A” AND SHALL BE FURNISHED CLEANED, PACKAGED, AND LABELED IN ACCORDANCE WITH ARP1176 CATEGORY 1A. /

23、16/ EXAMPLE OF PART NUMBER: AS6117 D 08 06 A OPTIONAL OXYGEN CLEANING /15/ BASIC PART NUMBER END 2 - SIZE CODE IN .062 INCH INCREMENTS (06 = .375 INCHES) MATERIAL CODE LETTER /1/ END 1 - SIZE CODE IN .062 INCH INCREMENTS (08 = .500 INCHES) 17. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE C

24、ONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.