SAE AS 5382 4A-2006 CABLE FIBER OPTIC SINGLE-MODE 4 6 125 450 um HERMETIC COATED TIGHT BUFFER《涂密封层的4 6 125 450 m单模紧套光纤光缆》.pdf

《SAE AS 5382 4A-2006 CABLE FIBER OPTIC SINGLE-MODE 4 6 125 450 um HERMETIC COATED TIGHT BUFFER《涂密封层的4 6 125 450 m单模紧套光纤光缆》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 5382 4A-2006 CABLE FIBER OPTIC SINGLE-MODE 4 6 125 450 um HERMETIC COATED TIGHT BUFFER《涂密封层的4 6 125 450 m单模紧套光纤光缆》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、 AEROSPACE STANDARD CABLE, FIBER OPTIC, SINGLE-MODE, 4.6/125/450 m, HERMETIC COATED, TIGHT BUFFER AS5382/4 Copyright 2006 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechan

2、ical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2004-04REVISED 2006

3、-12 THIRD ANGLE PROJECTION CUSTODIAN: SAE AE-8/AE-8D REV. A FEDERAL SUPPLY CLASS6010 AS5382/4 SHEET 1 OF 4 REV. A SAE TechnicalStandards Board Rules provide that: “This report is published by SAE toadvance thestate of technical andengineering sciences.The use of thisreport is entirely voluntary, and

4、its applicabilityandsuitability forany particularuse,including any patent infringement arising therefrom, is thesole responsibility oftheuser.” SAE reviews each technical report at least every five yearsat which time it may be reaffirmed, revised, orcancelled.SAE invites yourwritten commentsandsugge

5、stions.RATIONALE REVISED TO MAKE CABLE MORE PRODUCIBLE. FIGURE 1 - CABLE CONFIGURATION 1. Construction Description 1.1 Optical Fiber Dimensions and Materials Core Diameter: 4.6 m nom. (0.00018 in) Mode Field Diameter 1310 nm: 5.1 m 1.0 m (0.00020 in 0.00004 in) Mode Field Diameter 1550 nm: 5.8 m 1.0

6、 m (0.00023 in 0.00004 in) Core Material: Step Index Silica Glass Cladding Diameter: 125 m 2 m (0.0049 in 0.00008 in) Cladding Material: Silica Glass Core to Cladding Ellipticity: 2% maximum Core to Cladding Offset: 1 m maximum Hermetic Coated: Yes Coating Diameter: 450 m 25 m (0.0177 in 0.001 in) C

7、oating Material: Silicone Coating Concentricity: 65% minimum 125 MICRON OD HERMETIC COATED GLASS FIBER SILICONE COATING ETFE UPJACKET BRAIDED PARA-ARAMID FIBER STRENGTH MEMBER 1.8 MM ETFE OUTER JACKET AEROSPACE STANDARD CABLE, FIBER OPTIC, SINGLE-MODE, 4.6/125/450 m, HERMETIC COATED, TIGHT BUFFER AS

8、5382/4 REV. A AS5382/4 SHEET 2 OF 4 REV. A 1.2 Cable Dimensions and Materials Upjacket Diameter: 900 m 50 m (0.0354 in 0.002 in) Upjacket Material: Ethylene-Tetrafluoroethylene Copolymer (ETFE) Strength Member: Braided Para-Aramid Fiber Yarn Size: 380 Denier Number of Ends: 16 Braid Picks/Inch: 14.5

9、 Outer Jacket Diameter: 1800 m 100 m (0.0709 in max 0.039 in max) Outer Jacket Material: Ethylene-Tetrafluoroethylene Copolymer (ETFE) Outer Jacket Concentricity: 6% of Jacket Outer Diameter 1.3 Cable Performance Operational Mode: Single mode Temperature Rating: -55 to +165 C Storage Temperature: -5

10、5 to +85 C Outer Jacket Color: Yellow Finished Cable Weight: 4.0 kg/km maximum 2. Optical Fiber Requirements Maximum Attenuation: 1.5 dB/km 1310 nm, 1.4 dB/km 1550 nm Numerical Aperture: 0.21 nominal Fiber Tensile Proof Test: 200,000 psi minimum 3. Environmental Fluid Immersion: See Table 1 for test

11、 fluid listing. Freezing Water Immersion: 0.5 dB change in optical transmittance during the test with 0.5 dB permanent change after test Humidity Resistance: 0.5 dB change in optical transmittance during the test with 0.5 dB permanent change after test Wicking: Water Penetration of 88.5 mm maximum F

12、ungus Resistance: Fungus inert per MIL-HDBK-454 Guideline 4 Blocking: No areas of localized adhesion 4. Mechanical Cold Bend: 0.5 dB change in optical transmittance after test Cyclic Flex: 0.5 dB change in optical transmittance during the test with 0.5 dB permanent change after test Test temps: -55

13、C, +25 C, +150 C Impact Resistance: 0.5 dB change in optical transmittance during the test with 0.5 dB permanent change after test Test Cycles: 50 at -55C, 100 at +25 C, 50 at +150 C Crush Resistance: 0.5 dB change in optical transmittance during the test with 0.5 dB permanent change after test AERO

14、SPACE STANDARD CABLE, FIBER OPTIC, SINGLE-MODE, 4.6/125/450 m, HERMETIC COATED, TIGHT BUFFER AS5382/4 REV. A AS5382/4 SHEET 3 OF 4 REV. A Corner Bend: 0.5 dB change in optical transmittance during the test with 0.5 dB permanent change after test Cable Tensile Load and 0.5 dB change in optical transm

15、ittance during the test with Bending: 0.5 dB permanent change after test Maximum tensile load 132 N Jacket Material Tensile Strength: 900 N/cm2minimum Tensile and Elongation: Elongation: 125% minimum Durability of Manufacturers Required unless identification marking is under a clear jacket Identific

16、ation: Jacket Strippability: Easily Removed, No damage to fiber at 10X 5. Thermal Flammability: After Flame: 30 seconds maximum Flame Travel: 3 inches maximum Tissue Flaming: None Thermal Shock: Temperature Range: -55 to +165 C Maximum Cable Diameter Change of 10% 0.5 dB change in optical transmitta

17、nce after test Property Retention 750 h at 180 C After Thermal Aging: 300 h at 200 C 100 h at 220 C Maximum Cable Diameter Change of 10% 0.5 dB change in optical transmittance after test jacket tensile and elongation: 75% of initial value Storage Life: Temperature Range: -55 to +85 C No Visual Damag

18、e at 10X Magnification 0.5 dB change in optical transmittance after test Temperature Cycling: 5 cycles, temperature range: -55 to +165 C Maximum Cable Diameter Change of 10% 0.5 dB change in optical transmittance during the test with 0.5 dB permanent change after test Temperature Cycling 5 cycles, t

19、emperature range: -55 to +165 C With Mandrel: Wrapped 5 times around a 0.75 inch mandrel 0.5 dB change in optical transmittance during the test with 0.5 dB permanent change after test Jacket Shrinkage: 2.3 mm maximum in a 360 mm sample AEROSPACE STANDARD CABLE, FIBER OPTIC, SINGLE-MODE, 4.6/125/450

20、m, HERMETIC COATED, TIGHT BUFFER AS5382/4 REV. A AS5382/4 SHEET 4 OF 4 REV. A TABLE 1 - IMMERSION TEST FLUIDS TEST FLUID TEST TEMPERATURE IMMERSION TIME MIL-PRF-23699, Lubricating Oil, Aircraft Turbine Engine, Synthetic Base 48 to 50 C 20 hours MIL-PRF-5606, Hydraulic Fluid, Petroleum Base, Aircraft

21、, Missile and Ordnance 48 to 50 C 20 hours TT-I-735, Isopropyl Alcohol (Grade A or B) 20 to 25 C 168 hours MIL-DTL-5624, Turbine Fuel, Aviation, Grade JP-4 and JP-5 20 to 25 C 168 hours SAE AMS 1424, Deicing/Anti-Icing Fluid, Aircraft, SAE Type I propylene glycol based 48 to 50 C 20 hours SAE AMS 14

22、35, Fluid, Deicing/Anti-Icing, Runways and Taxiways 48 to 50 C 20 hours MIL-C-43616, Cleaning Compound, Aircraft Surface 48 to 50 C 20 hours ASTM D 1153, Methyl Isobutyl Ketone (for use in Organic Coatings) 20 to 25 C 168 hours MIL-PRF-7808, Lubricating Oil, Aircraft Turbine Engine, Synthetic Base 1

23、18 to 121 C 30 minutes MIL-PRF-85570, Type 3 Cleaning Compound Alkaline 63 to 68 C 20 hours MIL-PRF-87252, Coolant Fluid, Hydrolytically Stable, Dielectric (POA) 20 to 25 C 168 hours MIL-DTL-83133, Turbine Fuel, Aviation Grade, JP-8 20 to 25 C 168 hours MIL-PRF-83282, Hydraulic Fluid 48 to 50 C 20 h

24、ours Halon Bromotrifluoromethane (CFBR) Gas at -76 C 48 to 50 C 168 hours Halon Bromotrifluoromethane (CFBR) Gas at -76 C -55 to -65 C 168 hours THE CHANGE BAR ( l ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT.