SAE AS 4684C-2009 FITTING ASSEMBLY ELBOW 45 FLARELESS AND SHORT FLARELESS REDUCER RETAINED NUT《固定螺母非扩口和短非扩口45弯头配件》.pdf

《SAE AS 4684C-2009 FITTING ASSEMBLY ELBOW 45 FLARELESS AND SHORT FLARELESS REDUCER RETAINED NUT《固定螺母非扩口和短非扩口45弯头配件》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 4684C-2009 FITTING ASSEMBLY ELBOW 45 FLARELESS AND SHORT FLARELESS REDUCER RETAINED NUT《固定螺母非扩口和短非扩口45弯头配件》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、 AEROSPACE STANDARD FITTING ASSEMBLY, ELBOW, 45, FLARELESS ANDSHORT FLARELESS, REDUCER, RETAINED NUT AS4684Copyright 2009 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechan

2、ical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1992-07REAFFIRMED 2

3、007-10REVISED 2009-02THIRD ANGLE PROJECTION CUSTODIAN: G-3/G-3B REV.C FEDERAL SUPPLY CLASS 4730 AS4684 SHEET 1 OF 6 REV. C PROCUREMENT SPECIFICATION: /4/ AS18280SAE TechnicalStandards Board Rules provide that: “This report is published by SAE toadvance thestate of technical andengineering sciences.

4、Theuse of thisreport is entirely voluntary, andits applicabilityandsuitability forany particularuse,including any patent infringement arising therefrom, is thesole responsibility oftheuser.”SAE reviews each technical report at least every five yearsat which time it may be reaffirmed, revised, orcanc

5、elled.SAE invites yourwritten commentsandsuggestions.SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS4684C RATIONALE PROCUREMENT SPECIFICATION CHANGED FROM AS4444 TO AS18280 AND PROCUREMENT NOTE UPDATED. WARNING NOTICE FOR CADM

6、IUM PLATING HAS BEEN INSERTED. UPDATES: MIL-S-8879 CLASS B TO AS8879 CLASS 3B. MATERIAL AND FINISH: FINISH SPECIFICATIONS UPDATED. FIGURE 1 - ELBOW ASSEMBLY, 45 FIGURE 2 - INSTALLATION, RETAINED NUT AND RETAINING WIRE Copyright SAE International Provided by IHS under license with SAENot for ResaleNo

7、 reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS4684 SHEET 2 OF 6 REV. C FITTING ASSEMBLY, ELBOW, 45, FLARELESS AND SHORT FLARELESS, REDUCER, RETAINED NUT TABLE 1 - DIMENSIONS AND WEIGHTS BASIC NO. AS4684 /10/ /18/ SIZE CODE D H J +.005/-.020 LB/EA APPROX REF

8、ALUM LB/EA APPROX REF CRES LB/EA APPROX REF TI 20 .517 .124 1.375 .268 .779 .451 24 .614 .156 1.688 .381 1.098 .636 TABLE 2 - WIRE INSERTION DEPTH PORT SIZE (NOMINAL TUBE SIZE) C 04 .250 .076 05 .312 .076 06 .375 .084 08 .500 .095 10 .625 .114 12 .750 .150 16 1.000 .176 20 1.250 .247 24 1.500 .287 T

9、ABLE 3 - LEG LENGTH A SIZE OF PORT #2 FORGING SIZE /10/ 20 FORGING SIZE /10/ 24 04 .876 .928 05 .876 .928 06 .892 .944 08 .985 1.037 10 1.048 1.10012 1.111 1.16316 1.111 1.16320 1.053 .956 24 - 1.105TABLE 4 - LEG LENGTH B SIZE OF PORT #1 FORGING SIZE /10/ 20 FORGING SIZE /10/ 24 04 .853 .950 05 .905

10、 .957 06 .966 1.018 08 1.063 1.11510 1.142 1.194 12 1.131 1.18316 1.179 1.231 20 1.055 1.10724 - 1.135Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS4684 SHEET 3 OF 6 REV. C FIT

11、TING ASSEMBLY, ELBOW, 45, FLARELESS AND SHORT FLARELESS, REDUCER, RETAINED NUT TABLE 5 - TUBE SIZE AND CORRESPONDING THREADS PORT SIZE (NOMINAL TUBE SIZE) T THREAD PER AS8879 CLASS 3B 04 .250 .4375-20UNJF 05 .312 .5000-20UNJF 06 .375 .5625-18UNJF 08 .500 .7500-16UNJF 10 .625 .8750-14UNJF 12 .750 1.0

12、625-12UNJ 16 1.000 1.3125-12UNJ 20 1.250 1.5625-12UNJ24 1.500 1.8125-12UNJ NOTES: NOTICE THIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE. /1/ MATERIAL: a. CODE LETTER T: (1) BODY: TYPE 6AL-4V TITANIUM

13、 ALLOY PER AMS4928 (2) NUT: CODE LETTER T OF AS4702 OR AS1790 REFERENCE (TYPE 6AL-4V TITANIUM ALLOY) (3) WIRE: PER AS4701 OR AS1791 REFERENCE (CLASS 302 OR 305 CORROSION RESISTANT STEEL) b. CODE LETTER V: (1) BODY: TYPE 15-5PH CORROSION RESISTANT STEEL PER AMS5659 (2) NUT: CODE LETTER V OF AS4702 OR

14、 AS1790 REFERENCE (TYPE 15-5PH CORROSION RESISTANT STEEL) (3) WIRE: PER AS4701 OR AS1791 REFERENCE (CLASS 302 OR 305 CORROSION RESISTANT STEEL) c. CODE LETTER W: (1) BODY: TYPE 7075-T73 ALUMINUM ALLOY FORGING PER AMS4141 OR TYPE 7075-T7351 ALUMINUM ALLOY BAR PER AMS4124 (2) NUT: CODE LETTER W OF AS4

15、702 OR AS1790 REFERENCE (TYPE 7075-T73 ALUMINUM ALLOY) (3) WIRE: PER AS4701 OR AS1791 REFERENCE (CLASS 302 OR 305 CORROSION RESISTANT STEEL) Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE

16、STANDARD AS4684 SHEET 4 OF 6 REV. C FITTING ASSEMBLY, ELBOW, 45, FLARELESS AND SHORT FLARELESS, REDUCER, RETAINED NUT 2. HEAT TREAT a. MATERIAL CODE LETTER T: (1) BODY, NUT, AND WIRE: NONE b. MATERIAL CODE LETTER V: (1) BODY: HEAT TREAT TO CONDITION H-1075 PER AMS2759/3 (2) NUT: MATERIAL CODE LETTER

17、 V OF AS4702 OR AS1790 REFERENCE (HEAT TREAT TO CONDITION H-1075) (3) WIRE: NONE c. MATERIAL CODE LETTER W: (1) BODY, NUT, AND WIRE: NONE /3/ FINISH: a. MATERIAL CODE LETTER T: (1) BODY: FLUORIDE PHOSPHATE CONVERSION COAT PER AMS2486 (2) NUT: CODE LETTER T OF AS4702 OR AS1790 WITH SUFFIX N REFERENCE

18、 (FLUORIDE PHOSPHATE CONVERSION COAT AND COAT WITH SOLID FILM LUBRICANT ON ID) (3) WIRE: PER AS4701 OR AS1791 REFERENCE (PASSIVATE AND COAT WITH SOLID FILM LUBRICANT) b. MATERIAL CODE LETTER V: (1) BODY: (a) V CODE PARTS TO BE PASSIVATED ONLY WILL HAVE NO FINISH CODE LETTER AFTER THE PART NUMBER. TH

19、E FINISH WILL BE: PASSIVATE PER AMS2700 PER PROCUREMENT SPECIFICATION. (b) V CODE PARTS TO BE CADMIUM PLATED ONLY WILL HAVE THE FINISH CODE LETTER “P” AFTER THE SIZE CODE IN THE PART NUMBER. THE FINISH WILL BE: CADMIUM PLATE PER AMS-QQ-P-416, TYPE II, CLASS 2 (2) NUT: CODE LETTER V OF AS4702 OR AS17

20、90 REFERENCE (a) NO FINISH CODE LETTER AT END OF PART NUMBER: PASSIVATE AND COAT WITH SOLID FILM LUBRICANT ON ID (b) FINISH CODE LETTER P AT END OF PART NUMBER: CADMIUM PLATE (3) WIRE: PER AS4701 OR AS1791 REFERENCE (PASSIVATE AND COAT WITH SOLID FILM LUBRICANT) c. MATERIAL CODE LETTER W: (1) BODY:

21、ANODIZE PER AMS2472 OR MIL-A-8625, TYPE II, CLASS 2 DYED BROWN, SIMILAR TO COLOR 10080 OF FED-STD-595 (2) NUT: CODE LETTER W OF AS4702 OR AS1790 WITH SUFFIX N REFERENCE (ANODIZE DYED BROWN AND COAT WITH SOLID FILM LUBRICANT) (3) WIRE: PER AS4701 OR AS1791 REFERENCE (PASSIVATE AND COAT WITH SOLID FIL

22、M LUBRICANT) Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS4684 SHEET 5 OF 6 REV. C FITTING ASSEMBLY, ELBOW, 45, FLARELESS AND SHORT FLARELESS, REDUCER, RETAINED NUT /4/ PROCUR

23、EMENT SPECIFICATION: AS18280 EXCEPT AS SPECIFIED ON THIS STANDARD. PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER AS LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST PRI-QPL-AS18280 FOR THIS STANDARD. SEE http:/ FOR CURRENT QPL ONLI

24、NE. NOTE: PRI-QPL LIMITATION - WITH REVISION C OF THIS STANDARD THE PROCUREMENT SPECIFICATION HAS BEEN CHANGED FROM AS4444 FOR 5000 psi TO AS18280 FOR 3000 psi. USERS OF THIS FITTING FOR 5000 psi APPLICATIONS PER AS4444 ARE ADVISED TO CONTROL SOURCE APPROVAL BY STANDARD PAGE SUPPLEMENT OR SIMILAR ME

25、ANS. /5/ IDENTIFICATION AT LOCATION SHOWN: MARK PER AS478 CLASS C OR D OR METHOD 7A3, 15A3, OR 15B. MANUFACTURERS NAME, TRADEMARK OR CAGE CODE, BASIC PART NUMBER AND MATERIAL CODE LETTER. 6. THIS PART IS DESIGNED FOR USE IN SYSTEMS WITH OPERATING PRESSURES AS FOLLOWS: a. SIZES -20 AND -24 TITANIUM A

26、LLOY AND CORROSION RESISTANT STEEL AT 3000 psi b. SIZES -20 AND -24 ALUMINUM ALLOY AT 600 psi LARGEST PORT DETERMINES PRESSURE RATING. 7. WHEN MACHINED FROM BAR OR OVERSIZED FORGINGS, THE CENTER BODY SECTION SHALL CONFORM TO AS1376, TABLE 10. /8/ RADIUS APPLICABLE FOR TITANIUM PARTS ONLY. /9/ RETAIN

27、ED NUT AND RETAINING WIRE: a. TUBE SIZES 1.250 AND 1.500: AS4702 RETAINED NUT AND AS4701 RETAINING WIRE b. TUBE SIZES 1.000 AND SMALLER: AS1790 RETAINED NUT AND AS1791 RETAINING WIRE ASSEMBLE RETAINED NUT TO FITTING BODY WITH RETAINING WIRE AS SHOWN IN FIGURE 2. THE NUT SHALL BE FREE TO ROTATE AFTER

28、 ASSEMBLY. /10/ LARGEST PORT DETERMINES FORGING SIZE REGARDLESS OF THE LOCATION. MINIMUM FORGING SIZE IS -20. THIS STANDARD IS FOR REDUCERS ONLY; FOR ALL PORTS THE SAME SIZE USE AS4667. 11. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNIC

29、AL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT C

30、ONTAIN EDITORIAL CHANGES ONLY. 12. INVENTORIED PARTS CONFORMING TO THE PREVIOUS “LETTER CHANGE” MAY BE USED TO DEPLETION /4/. 13. INTERPRETATION OF DRAWING PER ARP4296. 14. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M; REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125

31、 in Ra. 15. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 16. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994 17. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .010, ANGULAR DIMENSIONS 5 DEGREES. Copyright SAE International Provided by IHS under license with S

32、AENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS4684 SHEET 6 OF 6 REV. C FITTING ASSEMBLY, ELBOW, 45, FLARELESS AND SHORT FLARELESS, REDUCER, RETAINED NUT /18/ Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-