SAE AS 3611B-2017 BOLT MACHINE - DOUBLE HEXAGON EXTENDED WASHER HEAD PD SHANK COBALT-NICKEL ALLOY UNS R30159 260 KSI MIN.pdf

《SAE AS 3611B-2017 BOLT MACHINE - DOUBLE HEXAGON EXTENDED WASHER HEAD PD SHANK COBALT-NICKEL ALLOY UNS R30159 260 KSI MIN.pdf》由会员分享，可在线阅读，更多相关《SAE AS 3611B-2017 BOLT MACHINE - DOUBLE HEXAGON EXTENDED WASHER HEAD PD SHANK COBALT-NICKEL ALLOY UNS R30159 260 KSI MIN.pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、 AEROSPACE STANDARD BOLT, MACHINE DOUBLE HEXAGON EXTENDED WASHER HEAD, PD SHANK, COBALT-NICKEL ALLOY UNS R30159, 260 KSI MIN $6Copyright 2017 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means

2、, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISS

3、UED2004-03REVISED2017-01THIRD ANGLE PROJECTION CUSTODIAN: E-25 REV.B FEDERAL SUPPLY CLASS 5306 $6 SHEET 1 OF 13 REV. B PROCUREMENT SPECIFICATION: AS7475 6$(7HFKQLFDO6WDQGDUGV%RDUG5XOHVSURYLGHWKDW7KLVUHSRUWLVSXEOLVKHGE6$(WRDGYDQFHWKHVWDWHRIWHFKQLFDODQGHQJLneering sciences. The useof this report is en

4、tirely voluntary, and its applicability andsuitability for any particularuse, includingany patent infringement arisingtherefrom,LVWKHVROHUHVSRQVLELOLWRIWKHXVHUSAE reviews eachtechnical reportatleast every fiveyears at whichtime it may be revised, reaffirmed, stabilized, or cancelled. SAE invites you

5、r written comments and suggestions.SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS3611B RATIONALE DELETE RADIUS AT TRANSITION FROM WRENCH PADS TO BASE FLANGE, REVISE DEPICTION OF BOTTOM OF LIGHTENING HOLE, UPDATE REFERENCES, CORRECT TYPO I

6、N APPROX MASS FOR AS3611-6-60. CORRECT ERRORS IN APPROXIMATE MASS FOR AS3611-12-20 THROUGH AS3611-12-96, ADD NEW NOTE FOR EXISTING INVENTORY DISPOSITION, UPDATE FPI REFERENCE, FIGURE 1 RE-DRAWN, GENERAL EDITORIAL UPDATE. FIGURE 1 - BOLT AEROSPACE STANDARD $6 SHEET 2 OF 13 REV. B BOLT, MACHINE DOUBLE

7、 HEXAGON EXTENDED WASHER HEAD, PD SHANK, COBALT-NICKEL ALLOY UNS R30159, 260 KSI MIN TABLE 1 TABLE 1A - DASH NUMBERS, THREAD D, AS870 DASH NO., AND DIMENSIONS B, C, E, F, G, AND H DASH NO. THREAD D AS870 DASH NO. B NOMINAL C E F MIN G H MIN -3 .1900-32 UNJF-3A 08 .2500 .165-.175 .365- .385 .335 .240

8、- .260 .020 -4 .2500-28 UNJF-3A 10 .3125 .222-.232 .455- .475 .425 .302- .322 .026 -5 .3125-24 UNJF-3A 12 .3750 .280-.290 .570- .590 .540 .365- .385 .035 -6 .3750-24 UNJF-3A 14 .4375 .343-.353 .686- .706 .656 .428- .448 .044 -7 .4375-20 UNJF-3A 16 .5000 .400-.410 .802- .822 .772 .490- .510 .053 -8 .

9、5000-20 UNJF-3A 18 .5625 .462-.472 .917- .937 .887 .552- .572 .062 -9 .5625-18 UNJF-3A 20 .6250 .521-.531 1.032-1.052 1.002 .615- .635 .071 -10 .6250-18UNJF-3A 22 .6875 .584-.594 1.148-1.168 1.118 .677- .697 .080 -12 .7500-16UNJF-3A 26 .8125 .704-.714 1.379-1.399 1.349 .802- .822 .098 -14 .8750-14UN

10、JF-3A 30 .9375 .824-.834 1.610-1.630 1.580 .927- .947 .116 -16 1.000-12UNJF-3A 34 1.0625 .941-.951 1.841-1.861 1.811 1.052-1.072 .134 TABLE 1B - DASH NUMBERS AND DIMENSIONS K, R, T, U, V, AB, AC, AND AD DASH NO. K R T MIN U V AB AC AD -3 .248-.268 .015-.025 .122 .114-.134 .090-.110 .110-.130 .006 .0

11、03 -4 .293-.313 .020-.030 .144 .150-.170 .140-.160 .164-.184 .007 .003 -5 .354-.374 .026-.036 .166 .188-.208 .196-.216 .219-.239 .008 .003 -6 .405-.425 .033-.043 .188 .225-.245 .250-.270 .281-.301 .010 .0025 -7 .462-.482 .039-.049 .210 .262-.282 .300-.320 .334-.354 .010 .0025 -8 .510-.530 .045-.055

12、.232 .300-.320 .360-.380 .396-.416 .012 .002 -9 .558-.578 .051-061 .254 .338-.358 .430-.450 .452-.472 .013 .002 -10 .635-.655 .058-.068 .336 .375-.395 .490-.510 .514-.534 .016 .002 -12 .735-.755 .070-.080 .371 .450-.470 .560-.580 .630-.650 .017 .002 -14 .875-.895 .082-.092 .442 .525-.545 .640-.660 .

13、744-.764 .022 .002 -16 .975-.995 .095-.105 .512 .600-.620 .730-.750 .854-.874 .025 .002 NOTES /1/ FOR PARTS WITH A MINIMUM SHANK LENGTH (DIMENSION 1 (48$/7225/( SS THAN 1.5D, DATUM Z SHALL REPLACE DATUM Y. 2. MATERIAL: COBALT-NICKEL ALLOY PER AMS5842 (UNS R30159). 3. PROCUREMENT SPECIFICATION: AS747

14、5. 4. FLUORESCENT PENETRANT INSPECTION PER ASTM E1417/E1417M TYPE 1, SENSITIVITY LEVEL 2 MINIMUM. 5. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, SURFACES TO BE 125 MICROINCHES Ra. 6. BREAK SHARP EDGES .003 TO .015, UNLESS OTHERWISE SPECIFIED. 7

15、. DIMENSIONS IN INCHES. 8. UNLESS OTHERWISE SPECIFIED, PART INVENTORY MANUFACTURED TO PREVIOUS REVISIONS OF THE APPLICABLE DRAWING OR SPECIFICATION MAY BE PROCURED AND USED UNTIL STOCK IS DEPLETED AEROSPACE STANDARD $6 SHEET 3 OF 13 REV. B BOLT, MACHINE DOUBLE HEXAGON EXTENDED WASHER HEAD, PD SHANK,

16、 COBALT-NICKEL ALLOY UNS R30159, 260 KSI MIN 9. DIMENSIONING AND TOLERANCING PER ANSI Y14.5-1982 (ASME PUBLICATION). 10. DO NOT USE UNASSIGNED PART NUMBERS. 11. THE PART NUMBER SHALL CONSIST OF THE BASIC PART NUMBER, FIRST DASH NUMBER DESIGNATING THE NOMINAL DIAMETER AND THE SECOND DASH NUMBER DESIG

17、NATING THE NOMINAL LENGTH IN SIXTEENTHS (.0625) OF AN INCH. EXAMPLE OF COMPLETE PART NUMBER: 12. REVISION INDICATOR: A CHANGE BAR (I) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE

18、 OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. AS AND AMS ARE SAE INTERNATIONAL PUBLICATI

19、ONS. ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION. ASTM IS AN ASTM INTERNATIONAL PUBLICATION. TABLE 2 - PART NUMBERS AND DIMENSIONS L, M, N, AND APPROXIMATE MASS FOR .1900 NOMINAL DIAMETER BOLTS PART NUMBER L M MAX N MIN APPROX MASS LB/100 PART NUMBER L M MAX N MIN APPROX MASS LB/

20、100 AS3611-3-06 .365- .385 .088 .025 .710 AS3611-3-27 1.678-1.698 1.058 .936 1.592 AS3611-3-07 .428- .448 .088 .025 .752 AS3611-3-28 1.740-1.760 1.120 .998 1.634 AS3611-3-08 .490- .510 .088 .025 .794 AS3611-3-29 1.802-1.822 1.182 1.060 1.676 AS3611-3-09 .552- .572 .088 .025 .836 AS3611-3-30 1.865-1.

21、885 1.245 1.123 1.718 AS3611-3-10 .615- .635 .088 .025 .878 AS3611-3-31 1.928-1.948 1.308 1.186 1.760 AS3611-3-11 .678- .698 .088 .025 .920 AS3611-3-32 1.990-2.010 1.370 1.248 1.802 AS3611-3-12 .740- .760 .120 .025 .962 AS3611-3-34 2.115-2.135 1.495 1.373 1.886 AS3611-3-13 .802- .822 .183 .060 1.004

22、 AS3611-3-36 2.240-2.260 1.620 1.498 1.970 AS3611-3-14 .865- .885 .245 .123 1.046 AS3611-3-38 2.365-2.385 1.745 1.623 2.054 AS3611-3-15 .928- .948 .308 .186 1.088 AS3611-3-40 2.490-2.510 1.870 1.748 2.138 AS3611-3-16 .990-1.010 .370 .248 1.130 AS3611-3-42 2.615-2.635 1.995 1.873 2.222 AS3611-3-17 1.

23、052-1.072 .432 .310 1.172 AS3611-3-44 2.740-2.760 2.120 1.998 2.306 AS3611-3-18 1.115-1.135 .495 .373 1.214 AS3611-3-46 2.865-2.885 2.245 2.123 2.390 AS3611-3-19 1.178-1.198 .558 .436 1.256 AS3611-3-48 2.990-3.010 2.370 2.248 2.474 AS3611-3-20 1.240-1.260 .620 .498 1.298 AS3611-3-50 3.115-3.135 2.49

24、5 2.373 2.558 AS3611-3-21 1.302-1.322 .682 .560 1.340 AS3611-3-52 3.240-3.260 2.620 2.498 2.642 AS3611-3-22 1.365-1.385 .745 .623 1.382 AS3611-3-54 3.365-3.385 2.745 2.623 2.726 AS3611-3-23 1.428-1.448 .808 .686 1.424 AS3611-3-56 3.490-3.510 2.780 2.748 2.810 AS3611-3-24 1.490-1.510 .870 .748 1.466

25、AS3611-3-58 3.615-3.635 2.995 2.873 2.894 AS3611-3-25 1.552-1.572 .932 .810 1.508 AS3611-3-60 3.740-3.760 3.120 2.998 2.978 AS3611-3-26 1.615-1.635 .995 .873 1.550 AS3611-3-62 3.865-3.885 3.245 3.123 3.062 AEROSPACE STANDARD $6 SHEET 4 OF 13 REV. B BOLT, MACHINE DOUBLE HEXAGON EXTENDED WASHER HEAD,

26、PD SHANK, COBALT-NICKEL ALLOY UNS R30159, 260 KSI MIN TABLE 3 - PART NUMBERS AND DIMENSIONS L, M, N, AND APPROXIMATE MASS FOR .2500 NOMINAL DIAMETER BOLTS PART NUMBER L M MAX N MIN APPROX MASS LB/100 PART NUMBER L M MAX N MIN APPROX MASS LB/100 AS3611-4-07 .428- .448 .101 .030 1.561 AS3611-4-40 2.49

27、0-2.510 1.750 1.619 4.354 AS3611-4-08 .490- .510 .101 .030 1.641 AS3611-4-42 2.615-2.635 1.875 1.744 4.514 AS3611-4-09 .552- .572 .101 .030 1.721 AS3611-4-44 2.740-2.760 2.000 1.869 4.673 AS3611-4-10 .615- .635 .101 .030 1.800 AS3611-4-46 2.865-2.885 2.125 1.994 4.833 AS3611-4-11 .678- .698 .101 .03

28、0 1.880 AS3611-4-48 2.990-3.010 2.250 2.119 4.992 AS3611-4-12 .740- .760 .101 .030 1.960 AS3611-4-50 3.115-3.135 2.375 2.244 5.152 AS3611-4-13 .802- .822 .101 .030 2.040 AS3611-4-52 3.240-3.260 2.500 2.369 5.312 AS3611-4-14 .865- .885 .125 .030 2.120 AS3611-4-54 3.365-3.385 2.625 2.494 5.471 AS3611-

29、4-15 .928- .948 .188 .057 2.199 AS3611-4-56 3.490-3.510 2.750 2.619 5.631 AS3611-4-16 .990-1.010 .250 .119 2.279 AS3611-4-58 3.615-3.635 2.875 2.744 5.790 AS3611-4-17 1.052-1.072 .312 .181 2.359 AS3611-4-60 3.740-3.760 3.000 2.869 5.950 AS3611-4-18 1.115-1.135 .375 .244 2.439 AS3611-4-62 3.865-3.885

30、 3.125 2.994 6.110 AS3611-4-19 1.178-1.198 .438 .307 2.519 AS3611-4-64 3.990-4.010 3.250 3.119 6.269 AS3611-4-20 1.240-1.260 .500 .369 2.598 AS3611-4-66 4.115-4.135 3.375 3.244 6.429 AS3611-4-21 1.302-1.322 .562 .431 2.678 AS3611-4-68 4.240-4.260 3.500 3.369 6.588 AS3611-4-22 1.365-1.385 .625 .494 2

31、.758 AS3611-4-70 4.365-4.385 3.625 3.494 6.748 AS3611-4-23 1.428-1.448 .688 .557 2.838 AS3611-4-72 4.490-4.510 3.750 3.619 6.908 AS3611-4-24 1.490-1.510 .750 .619 2.918 AS3611-4-74 4.615-4.635 3.875 3.744 7.067 AS3611-4-25 1.552-1.572 .812 .681 2.997 AS3611-4-76 4.740-4.760 4.000 3.869 7.227 AS3611-

32、4-26 1.615-1.635 .875 .744 3.077 AS3611-4-78 4.865-4.885 4.125 3.994 7.386 AS3611-4-27 1.678-1.698 .938 .807 3.157 AS3611-4-80 4.990-5.010 4.250 4.119 7.546 AS3611-4-28 1.740-1.760 1.000 .869 3.237 AS3611-4-82 5.115-5.135 4.375 4.244 7.706 AS3611-4-29 1.802-1.822 1.062 .931 3.317 AS3611-4-84 5.240-5

33、.260 4.500 4.369 7.865 AS3611-4-30 1.865-1.885 1.125 .949 3.396 AS3611-4-86 5.365-5.385 4.625 4.494 8.025 AS3611-4-31 1.928-1.948 1.188 1.057 3.476 AS3611-4-88 5.490-5.510 4.750 4.619 8.184 AS3611-4-32 1.990-2.010 1.250 1.119 3.556 AS3611-4-90 5.615-5.635 4.875 4.744 8.344 AS3611-4-34 2.115-2.135 1.

34、375 1.244 3.716 AS3611-4-92 5.740-5.760 5.000 4.869 8.503 AS3611-4-36 2.240-2.260 1.500 1.369 4.035 AS3611-4-94 5.865-5.885 5.125 4.994 8.663 AS3611-4-38 2.365-2.385 1.625 1.494 4.195 AS3611-4-96 5.990-6.010 5.250 5.119 8.823 AEROSPACE STANDARD $6 SHEET 5 OF 13 REV. B BOLT, MACHINE DOUBLE HEXAGON EX

35、TENDED WASHER HEAD, PD SHANK, COBALT-NICKEL ALLOY UNS R30159, 260 KSI MIN TABLE 4 - PART NUMBERS AND DIMENSIONS L, M, N, AND APPROXIMATE MASS FOR .3125 NOMINAL DIAMETER BOLTS PART NUMBER L M MAX N MIN APPROX MASS LB/100 PART NUMBER L M MAX N MIN APPROX MASS LB/100 AS3611-5-08 .490- .510 .119 .036 2.

36、785 AS3611-5-42 2.615-2.635 1.750 1.607 7.590 AS3611-5-09 .552- .572 .119 .036 2.927 AS3611-5-44 2.740-2.760 1.875 1.732 7.875 AS3611-5-10 .615- .635 .119 .036 3.070 AS3611-5-46 2.865-2.885 2.000 1.857 8.159 AS3611-5-11 .678- .698 .119 .036 3.212 AS3611-5-48 2.990-3.010 2.125 1.982 8.444 AS3611-5-12

37、 .740- .760 .119 .036 3.355 AS3611-5-50 3.115-3.135 2.250 2.107 8.729 AS3611-5-13 .802- .822 .119 .036 3.497 AS3611-5-52 3.240-3.260 2.375 2.232 9.014 AS3611-5-14 .865- .885 .119 .036 3.639 AS3611-5-54 3.365-3.385 2.500 2.357 9.299 AS3611-5-15 .928- .948 .119 .036 3.782 AS3611-5-56 3.490-3.510 2.625

38、 2.482 9.583 AS3611-5-16 .990-1.010 .125 .036 3.924 AS3611-5-58 3.615-3.635 2.750 2.607 9.868 AS3611-5-17 1.052-1.072 .188 .045 4.067 AS3611-5-60 3.740-3.760 2.875 2.732 10.153 AS3611-5-18 1.115-1.135 .250 .107 4.209 AS3611-5-62 3.865-3.885 3.000 2.857 10.438 AS3611-5-19 1.178-1.198 .312 .170 4.351

39、AS3611-5-64 3.990-4.010 3.125 2.982 10.723 AS3611-5-20 1.240-1.260 .375 .232 4.494 AS3611-5-66 4.115-4.135 3.250 3.107 11.007 AS3611-5-21 1.302-1.322 .438 .294 4.636 AS3611-5-68 4.240-4.260 3.375 3.232 11.292 AS3611-5-22 1.365-1.385 .500 .357 4.779 AS3611-5-70 4.365-4.385 3.500 3.357 11.577 AS3611-5

40、-23 1.428-1.448 .562 .420 4.921 AS3611-5-72 4.490-4.510 3.625 3.482 11.862 AS3611-5-24 1.490-1.510 .625 .482 5.063 AS3611-5-74 4.615-4.635 3.750 3.607 12.147 AS3611-5-25 1.552-1.572 .688 .544 5.206 AS3611-5-76 4.740-4.760 3.875 3.732 12.431 AS3611-5-26 1.615-1.635 .750 .607 5.348 AS3611-5-78 4.865-4

41、.885 4.000 3.857 12.716 AS3611-5-27 1.678-1.698 .812 .670 5.491 AS3611-5-80 4.990-5.010 4.125 3.982 13.001 AS3611-5-28 1.740-1.760 .875 .732 5.633 AS3611-5-82 5.115-5.135 4.250 4.107 13.286 AS3611-5-29 1.802-1.822 .938 .794 5.775 AS3611-5-84 5.240-5.260 4.375 4.232 13.571 AS3611-5-30 1.865-1.885 1.0

42、00 .857 5.918 AS3611-5-86 5.365-5.385 4.500 4.357 13.855 AS3611-5-31 1.928-1.948 1.062 .920 6.060 AS3611-5-88 5.490-5.510 4.625 4.482 14.140 AS3611-5-32 1.990-2.010 1.125 .982 6.203 AS3611-5-90 5.615-5.635 4.750 4.607 14.425 AS3611-5-34 2.115-2.135 1.250 1.107 6.469 AS3611-5-92 5.740-5.760 4.875 4.7

43、32 14.710 AS3611-5-36 2.240-2.260 1.375 1.232 6.735 AS3611-5-94 5.865-5.885 5.000 4.857 14.955 AS3611-5-38 2.365-2.385 1.500 1.357 7.020 AS3611-5-96 5.990-6.010 5.125 4.982 15.279 AS3611-5-40 2.490-2.510 1.625 1.482 7.305 AEROSPACE STANDARD $6 SHEET 6 OF 13 REV. B BOLT, MACHINE DOUBLE HEXAGON EXTEND

44、ED WASHER HEAD, PD SHANK, COBALT-NICKEL ALLOY UNS R30159, 260 KSI MIN TABLE 5 - PART NUMBERS AND DIMENSIONS L, M, N, AND APPROXIMATE MASS FOR .3750 NOMINAL DIAMETER BOLTS PART NUMBER L M MAX N MIN APPROX MASS LB/100 PART NUMBER L M MAX N MIN APPROX MASS LB/100 AS3611-6-09 .552- .572 .126 .043 4.364

45、AS3611-6-42 2.615-2.635 1.625 1.482 10.460 AS3611-6-10 .615- .635 .126 .043 4.549 AS3611-6-44 2.740-2.760 1.750 1.607 10.829 AS3611-6-11 .678- .698 .126 .043 4.733 AS3611-6-46 2.865-2.885 1.875 1.732 11.199 AS3611-6-12 .740- .760 .126 .043 4.918 AS3611-6-48 2.990-3.010 2.000 1.857 11.568 AS3611-6-13

46、 .802- .822 .126 .043 5.103 AS3611-6-50 3.115-3.135 2.125 1.982 11.938 AS3611-6-14 .865- .885 .126 .043 5.288 AS3611-6-52 3.240-3.260 2.250 2.107 12.307 AS3611-6-15 .928- .948 .126 .043 5.472 AS3611-6-54 3.365-3.385 2.375 2.232 12.677 AS3611-6-16 .990-1.010 .126 .043 5.657 AS3611-6-56 3.490-3.510 2.

47、500 2.357 13.046 AS3611-6-17 1.052-1.072 .126 .043 5.842 AS3611-6-58 3.615-3.635 2.625 2.482 13.416 AS3611-6-18 1.115-1.135 .126 .043 6.026 AS3611-6-60 3.740-3.760 2.750 2.607 13.785 AS3611-6-19 1.178-1.198 .188 .045 6.211 AS3611-6-62 3.865-3.885 2.875 2.732 14.155 AS3611-6-20 1.240-1.260 .250 .107

48、6.396 AS3611-6-64 3.990-4.010 3.000 2.857 14.524 AS3611-6-21 1.302-1.322 .312 .169 6.580 AS3611-6-66 4.115-4.135 3.125 2.982 14.894 AS3611-6-22 1.365-1.385 .375 .232 6.765 AS3611-6-68 4.240-4.260 3.250 3.107 15.263 AS3611-6-23 1.428-1.448 .438 .295 6.950 AS3611-6-70 4.365-4.385 3.375 3.232 15.633 AS3611-6-24 1