SAE AS 3587A-2009 Pin and Plug Expansion Set of Parts Std and 010 Oversize Diameters Cres 303 Short UNS S30300《UNS S30300短型Cres 303标准和 010特大直径成套零件膨胀销钉和插头》.pdf

《SAE AS 3587A-2009 Pin and Plug Expansion Set of Parts Std and 010 Oversize Diameters Cres 303 Short UNS S30300《UNS S30300短型Cres 303标准和 010特大直径成套零件膨胀销钉和插头》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 3587A-2009 Pin and Plug Expansion Set of Parts Std and 010 Oversize Diameters Cres 303 Short UNS S30300《UNS S30300短型Cres 303标准和 010特大直径成套零件膨胀销钉和插头》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、AEROSPACE STANDARD (R) PIN AND PLUG, EXPANSION, SET OF PARTS, STD AND .010 OVERSIZE DIAMETERS, CRES 303, SHORT, UNS S30300 AS3587Copyright 2009 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any mea

2、ns, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSU

3、ED 1996-06REAFFIRMED 2006-10 REVISED 2009-02THIRD ANGLE PROJECTION CUSTODIAN: E-25 REV.AFEDERAL SUPPLY CLASS 5340 AS3587SHEET 1 OF 2REV. APROCUREMENT SPECIFICATION: NONESAE TechnicalStandards Board Rules provide that: “This report is published by SAE toadvance thestate of technical andengineering sc

4、iences. Theuse of thisreport is entirely voluntary, andits applicabilityandsuitability forany particularuse, including any patent infringement arising therefrom, is thesole responsibility oftheuser.”SAE reviews each technical report at least every five yearsat which time it may be reaffirmed, revise

5、d, orcancelled. SAE invites yourwritten commentsandsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS3587ARATIONALE ADD MANUFACTURERS PART NUMBERS, CLARIFY PART MARKING REQUIREMENTS AND GENERAL SAE UPDATING REQUIREME

6、NTS FOR FORMATING. FIGURE 1 - AS3132 PIN FIGURE 2 - AS3131 PLUG TABLE 1 - PART NUMBERS AEROSPACE STANDARD PARTNUMBER /3/MANUFACTURERSPARTNUMBER /3/PIN SIZE PLUG SIZE APPROX MASSLB/100 AS3587-01 PLGA0930030A AS3132-01 AS3131-01 .017 AS3587-02 PLGA1250030A AS3132-02 AS3131-02 .037 AS3587-03 PLGA156003

7、0A AS3132-03 AS3131-03 .060 AS3587-04 PLGA1870030A AS3132-04 AS3131-04 .110 AS3587-05 PLGA2180030A AS3132-05 AS3131-05 .182 AS3587-06 PLGA2500030A AS3132-06 AS3131-06 .275 AS3587-07 PLGA2810030A AS3132-07 AS3131-07 .419 AS3587-08 PLGA3430030A AS3132-08 AS3131-08 .704 AS3587-09 PLGA4060030A AS3132-09

8、 AS3131-09 1.161 AS3587-10 PLGA4680030A AS3132-10 AS3131-10 1.709 AS3587-11 PLGA5310030A AS3132-11 AS3131-11 2.923 AS3587-12 PLGA6560030A AS3132-12 AS3131-12 4.642 AS3587-51 PLGA1030030A AS3132-01 AS3131-51 .089 AS3587-52 PLGA1350030A AS3132-02 AS3131-52 .044 AS3587-53 PLGA1660030A AS3132-03 AS3131-

9、53(a) .067 AS3587-54 PLGA1970030A AS3132-04 AS3131-54(a) .122 AS3587-55 PLGA2280030A AS3132-05 AS3131-55(a) .202 AS3587-56 PLGA2600030A AS3132-06 AS3131-56(a) .296 (a) DESIGNATES .010 OVERSIZED PLUGS. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or

10、networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS3587SHEET 2 OF 2REV. A(R) PIN AND PLUG, EXPANSION, SET OF PARTS, STD AND .010 OVERSIZE DIAMETERS, CRES 303, SHORT, UNS S30300 TABLE 1 - PART NUMBERS (CONTINUED) AEROSPACE STANDARD PARTNUMBER /3/MANUFACTURERSPARTNUMBER /3/PIN SIZE

11、 PLUG SIZE APPROX MASSLB/100 AS3587-57 PLGA2910030A AS3132-07 AS3131-57(a) .444 AS3587-58 PLGA3530030A AS3132-08 AS3131-58(a) .844 AS3587-59 PLGA4160030A AS3132-09 AS3131-59(a) 1.226 AS3587-60 PLGA4780030A AS3132-10 AS3131-60(a) 1.786 AS3587-61 PLGA5410030A AS3132-11 AS3131-61(a) 3.017 AS3587-62 PLG

12、A6660030A AS3132-12 AS3131-62(a) 4.830 (a) DESIGNATES .010 OVERSIZED PLUGS. NOTES: 1. MATERIAL: 303 CRES BAR PER AMS5640, TYPE 1, UNS S30300, REF. 2. FINISH: a. PLUG: SEE AS3131 b. PIN: SEE AS3132 /3/ MARK AS3587-( ) PART NUMBER AND MANUFACTURERS PART NUMBER ON PACKAGE IN ACCORDANCE WITH AS478, METH

13、OD 37. IN ADDITION, PACKAGES FOR OVERSIZE PLUGS SHALL INCLUDE “OVERSIZE 303 SS” IN A RECTANGULAR BLOCK. 4. SEE AIR3276 FOR HOLE PREPARATION AND AIR 3277 FOR INSTALLATION PROCEDURE. 5. PIN AND PLUG EXPANSION SET OF PARTS SHALL CONTAIN A PIN SIZE FROM AS3132 AND A PLUG SIZE FROM AS3131 AS SPECIFIED WI

14、TH THE CORRESPONDING DASH NUMBER IN TABLE 1. 6. AS, AIR AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. 7. A CHANGE BAR ( l ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOC

15、UMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. APPROVED SOURCE OF SUPPLY: THE LEE CO WESTBROOK, CT FE

16、DERAL SUPPLY CODE FOR MANUFACTURERS NO 92555. ONLY THE ITEM DESCRIBED ON THIS DRAWING WHEN PROCURED FROM THE VENDOR LISTED HEREON IS APPROVED FOR USE IN THE APPLICATIONS SPECIFYING THIS AEROSPACE STANDARD IDENTIFICATION NUMBER. A SUBSTITUTE ITEM SHALL NOT BE USED WITHOUT PRIOR TESTING AND APPROVAL B

17、Y THE DESIGN ACTIVITY RESPONSIBLE FOR THE APPLICATION. IDENTIFICATION OF THE APPROVED SOURCE HEREON IS NOT TO BE CONSTRUED AS A GUARANTEE OF PRESENT OR CONTINUED AVAILABILITY AS A SOURCE OF SUPPLY FOR THE ITEM DESCRIBED ON THE DRAWING. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-