SAE AS 3586A-2009 Pin and Plug Expansion Set of Parts Cres 303 Long UNS S30300《UNS S30300长型Cres 303成套零件膨胀销钉和插头》.pdf

《SAE AS 3586A-2009 Pin and Plug Expansion Set of Parts Cres 303 Long UNS S30300《UNS S30300长型Cres 303成套零件膨胀销钉和插头》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 3586A-2009 Pin and Plug Expansion Set of Parts Cres 303 Long UNS S30300《UNS S30300长型Cres 303成套零件膨胀销钉和插头》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、AEROSPACE STANDARD (R) PIN AND PLUG, EXPANSION, SET OF PARTS CRES, 303, LONG, UNS S30300 AS3586Copyright 2009 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photoc

2、opying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1996-06REAFFIRMED 2006-10 REVIS

3、ED 2009-02THIRD ANGLE PROJECTION CUSTODIAN: E-25 REV.AFEDERAL SUPPLY CLASS 5340 AS3586SHEET 1 OF 2REV. APROCUREMENT SPECIFICATION: NONESAE TechnicalStandards Board Rules provide that: “This report is published by SAE toadvance thestate of technical andengineering sciences. Theuse of thisreport is en

4、tirely voluntary, andits applicabilityandsuitability forany particularuse, including any patent infringement arising therefrom, is thesole responsibility oftheuser.”SAE reviews each technical report at least every five yearsat which time it may be reaffirmed, revised, orcancelled. SAE invites yourwr

5、itten commentsandsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS3586ARATIONALE ADD MANUFACTURERS PART NUMBERS, CLARIFY PART MARKING REQUIREMENTS AND GENERAL SAE UPDATING REQUIREMENTS FOR FORMATING. FIGURE 1 - AS31

6、30 PIN FIGURE 2 - AS3129 PLUG TABLE 1 - PART NUMBERS AEROSPACE STANDARD PARTNUMBER /3/MANUFACTURERS PARTNUMBER /3/PIN SIZE PLUG SIZE APPROX MASSLB/100 AS3586-03 PLGA1561030A AS3130-03 AS3129-03 .166 AS3586-04 PLGA1871030A AS3130-04 AS3129-04 .179 AS3586-05 PLGA2181030A AS3130-05 AS3129-05 .283 AS358

7、6-06 PLGA2501030A AS3130-06 AS3129-06 .446 AS3586-07 PLGA2811030A AS3130-07 AS3129-07 .585 AS3586-08 PLGA3431030A AS3130-08 AS3129-08 1.082 AS3586-09 PLGA4061030A AS3130-09 AS3129-09 1.742 AS3586-10 PLGA4681030A AS3130-10 AS3129-10 2.630 AS3586-11 PLGA5311030A AS3130-11 AS3129-11 3.766 AS3586-12 PLG

8、A6561030A AS3130-12 AS3129-12 6.440 AS3586-53 PLGA1661030A AS3130-03 AS3129-53(a) .132 AS3586-54 PLGA1971030A AS3130-04 AS3129-54(a) .200 AS3586-55 PLGA2281030A AS3130-05 AS3129-55(a) .315 AS3586-56 PLGA2601030A AS3130-06 AS3129-56(a) .489 AS3586-57 PLGA2911030A AS3130-07 AS3129-57(a) .621 AS3586-58

9、 PLGA3531030A AS3130-08 AS3129-58(a) 1.148 AS3586-59 PLGA4161030A AS3130-09 AS3129-59(a) 1.839 AS3586-60 PLGA4781030A AS3130-10 AS3129-60(a) 2.751 AS3586-61 PLGA5411030A AS3130-11 AS3129-61(a) 3.890 AS3586-62 PLGA6661030A AS3130-12 AS3129-62(a) 6.688 (a) DESIGNATES .010 OVERSIZED PLUGS. Copyright SA

10、E International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS3586SHEET 2 OF 2REV. A(R) PIN AND PLUG, EXPANSION, SET OF PARTS CRES, 303, LONG, UNS S30300 NOTES: 1. MATERIAL: 303 CRES BAR PER AMS5640, TYPE

11、 1, REF. 2. FINISH: a. PLUG: SEE AS3129 b. PIN: SEE AS3130 /3/ MARK AS3586-( ) PART NUMBER AND MANUFACTURERS PART NUMBER ON PACKAGE IN ACCORDANCE WITH AS478, METHOD 37. IN ADDITION, PACKAGES FOR OVERSIZE PLUGS SHALL INCLUDE “OVERSIZE 303 SS” IN A RECTANGULAR BLOCK. 4. SEE AIR3276 FOR HOLE PREPARATIO

12、N AND AIR 3277 FOR INSTALLATION PROCEDURE. 5. PIN AND PLUG EXPANSION SET OF PARTS SHALL CONTAIN A PIN SIZE FROM AS3130 AND A PLUG SIZE FROM AS3129 AS SPECIFIED WITH THE CORRESPONDING DASH NUMBER IN TABLE 1. 6. AS, AIR AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. 7. A CHANGE BAR ( l ) LOCATED IN THE L

13、EFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANG

14、E BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. APPROVED SOURCE OF SUPPLY: THE LEE CO WESTBROOK, CT FEDERAL SUPPLY CODE FOR MANUFACTURERS NO 92555. ONLY THE ITEM DESCRIBED ON THIS DRAWING WHEN PROCURED FROM THE VENDOR LISTED HEREON IS APPRO

15、VED FOR USE IN THE APPLICATIONS SPECIFYING THIS AEROSPACE STANDARD IDENTIFICATION NUMBER. A SUBSTITUTE ITEM SHALL NOT BE USED WITHOUT PRIOR TESTING AND APPROVAL BY THE DESIGN ACTIVITY RESPONSIBLE FOR THE APPLICATION. IDENTIFICATION OF THE APPROVED SOURCE HEREON IS NOT TO BE CONSTRUED AS A GUARANTEE OF PRESENT OR CONTINUED AVAILABILITY AS A SOURCE OF SUPPLY FOR THE ITEM DESCRIBED ON THE DRAWING. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-