SAE AS 3417B-2017 BOLT MACHINE DOUBLE HEX EXTENDED WASHER HEAD CLOSE TOL SHANK UNS N07718 185 KSI MIN 1900-32 UNJF-3A (STRESS RUPTURE RESISTANT).pdf

《SAE AS 3417B-2017 BOLT MACHINE DOUBLE HEX EXTENDED WASHER HEAD CLOSE TOL SHANK UNS N07718 185 KSI MIN 1900-32 UNJF-3A (STRESS RUPTURE RESISTANT).pdf》由会员分享，可在线阅读，更多相关《SAE AS 3417B-2017 BOLT MACHINE DOUBLE HEX EXTENDED WASHER HEAD CLOSE TOL SHANK UNS N07718 185 KSI MIN 1900-32 UNJF-3A (STRESS RUPTURE RESISTANT).pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 AEROSPACE STANDARD BOLT, MACHINE, DOUBLE HEX, EXTENDED WASHER HEAD, CLOSE TOL. SHANK, UNS N07718, 185 KSI MIN .1900-32 UNJF-3A (STRESS RUPTURE RESISTANT) AS3417Copyright 2017 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transm

2、itted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE

3、WEB ADDRESS: http:/www.sae.org ISSUED1985-12 REAFFIRMED2006-05 REVISED2017-03THIRD ANGLE PROJECTION CUSTODIAN: E-25 REV.BFEDERAL SUPPLY CLASS 5306 AS3417 SHEET 1 OF 3 REV. B PROCUREMENT SPECIFICATION: AS7467 /3/ SAE TechnicalStandardsBoard Rulesprovidethat:“Thisreportispublished bySAEto advance the

4、state oftechnicaland engineering sciences.The use ofthisreportisentirelyvoluntary,anditsapplicabilityandsuitabilityforanyparticularuse,includinganypatentinfringementarising therefrom,isthe sole responsibilityoftheuser.”SAEreviewseachtechnicalreportatleasteveryfiveyearsatwhich time itmaybe revised,re

5、affirmed,stabilized,orcancelled.SAEinvitesyourwritten commentsandsuggestions.SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS3417B RATIONALE DELETE RADIUS AT TRANSITION OF WRENCH FLATS AND BASE FLANGE, UPDATE FEATURE CONTROL FRAME FOR STRAI

6、GHTNESS, ADD EDGE DISTANCE EXCEPTION FOR HEAD MARKING, ADD SURFACE TEXTURE REQUIREMENTS FOR HEAD, WRENCH FLATS AND BOLT END, ADD NEW NOTE FOR DISPOSITION OF EXISTING INVENTORY, UPDATE FPI REFERENCE AND ADD STANDARD SENSITIVITY REQUIREMENT, FIGURE 1 RE-DRAWN, AND GENERAL EDITORIAL CHANGES. FIGURE 1 -

7、 BOLT AEROSPACE STANDARD AS3417 SHEET 2 OF 3 REV. B BOLT, MACHINE, DOUBLE HEX, EXTENDED WASHER HEAD, CLOSE TOL. SHANK, UNS N07718, 185 KSI MIN .1900-32 UNJF-3A (STRESS RUPTURE RESISTANT) TABLE 1 - PART NUMBERS AND DIMENSIONS L, G, K, AND APPROX. MASS PART NUMBER L .010 G MIN K MAX APPROX MASS LB/100

8、 AS3417-03 AS3417-04 AS3417-05 AS3417-06 AS3417-07 AS3417-08 AS3417-09 AS3417-10 AS3417-11 AS3417-12 AS3417-13 AS3417-14 AS3417-15 AS3417-16 AS3417-17 AS3417-18 AS3417-19 AS3417-20 AS3417-21 AS3417-22 AS3417-23 AS3417-24 AS3417-25 AS3417-26 AS3417-27 AS3417-28 AS3417-29 AS3417-30 AS3417-31 AS3417-32

9、 AS3417-33 AS3417-34 AS3417-35 AS3417-36 AS3417-37 AS3417-38 AS3417-39 AS3417-40 AS3417-41 AS3417-42 AS3417-43 AS3417-44 AS3417-45 AS3417-46 AS3417-47 AS3417-48 AS3417-49 AS3417-50 AS3417-51 AS3417-52 AS3417-53 AS3417-54 AS3417-55 .607 .669 .731 .794 .857 .919 .981 1.044 1.107 1.169 1.231 1.294 1.35

10、7 1.419 1.481 1.544 1.607 1.669 1.731 1.794 1.857 1.919 1.981 2.044 2.107 2.169 2.231 2.294 2.357 2.419 2.481 2.544 2.607 2.669 2.731 2.794 2.857 2.919 2.981 3.044 3.107 3.169 3.231 3.294 3.357 3.419 3.481 3.544 3.607 3.669 3.731 3.794 3.857 .126 .188 .250 .312 .376 .438 .500 .562 .626 .688 .750 .81

11、2 .876 .938 1.000 1.062 1.126 1.188 1.250 1.312 1.376 1.438 1.500 1.562 1.626 1.688 1.750 1.812 1.876 1.938 2.000 2.062 2.126 2.188 2.250 2.312 2.376 2.438 2.500 2.562 2.626 2.688 2.750 2.812 2.876 2.938 3.000 3.062 3.126 3.188 3.250 3.312 3.376 .198 .260 .322 .385 .448 .510 .572 .635 .698 .760 .822

12、 .885 .948 1.010 1.072 1.135 1.198 1.260 1.322 1.385 1.448 1.510 1.572 1.635 1.698 1.760 1.822 1.885 1.948 2.010 2.072 2.135 2.198 2.260 2.322 2.385 2.448 2.510 2.572 2.635 2.698 2.760 2.822 2.885 2.948 3.010 3.072 3.135 3.198 3.260 3.322 3.385 3.448 .92 .97 1.02 1.08 1.13 1.18 1.23 1.28 1.33 1.38 1

13、.44 1.49 1.54 1.59 1.64 1.70 1.75 1.80 1.85 1.91 1.96 2.01 2.06 2.11 2.16 2.21 2.26 2.32 2.37 2.42 2.47 2.53 2.58 2.63 2.68 2.74 2.78 2.84 2.89 2.94 2.99 3.04 3.09 3.15 3.20 3.25 3.30 3.36 3.41 3.46 3.51 3.56 3.61 AEROSPACE STANDARD AS3417 SHEET 3 OF 3 REV. B BOLT, MACHINE, DOUBLE HEX, EXTENDED WASH

14、ER HEAD, CLOSE TOL. SHANK, UNS N07718, 185 KSI MIN .1900-32 UNJF-3A (STRESS RUPTURE RESISTANT) NOTES /1/ FOR PART NUMBERS AS3417-03 THROUGH AS3417-05, DATUM A SHALL REPLACE DATUM B. 2. MATERIAL: CORROSION AND HEAT RESISTANT NICKEL ALLOY AMS5662 (UNS N07718). /3/ PROCUREMENT SPECIFICATION: AS7467. EX

15、CEPT ROLL THREAD AND COLD WORK FILLET RADIUS AFTER PRECIPITATION HARDENING. 4. FLUORESCENT PENETRANT INSPECTION PER ASTM E1417/E1417M, SENSITIVITY LEVEL 2 MINIMUM. 5. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, SURFACES TO BE 125 MICROINCHES Ra

16、. EXCEPT UPSET HEAD TO BE 250 MICROINCHES Ra. 6. BREAK SHARP EDGES .003 TO .015, UNLESS OTHERWISE SPECIFIED. 7. DIMENSIONS ARE IN INCHES. 8. DIMENSIONS AND TOLERANCING: ANSI Y14.5M-1982 (ASME PUBLICATION). 9. UNLESS OTHERWISE SPECIFIED, PART INVENTORY MANUFACTURED TO PREVIOUS REVISIONS OF THE APPLIC

17、ABLE DRAWING OR SPECIFICATION MAY BE PROCURED AND USED UNTIL STOCK IS DEPLETED. 10. DO NOT USE UNASSIGNED PART NUMBERS. 11. REVISION INDICATOR: A CHANGE BAR (I) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN

18、 MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION. ASTM IS AN ASTM INTERNATIONAL PUBLICATION.