SAE AS 3413B-2016 BOLT MACHINE - HEXAGON HEAD PD SHANK UNS N07718 185 KSI 1900-32 UNJF-3A (STRESS RUPTURE RESISTANT).pdf

《SAE AS 3413B-2016 BOLT MACHINE - HEXAGON HEAD PD SHANK UNS N07718 185 KSI 1900-32 UNJF-3A (STRESS RUPTURE RESISTANT).pdf》由会员分享，可在线阅读，更多相关《SAE AS 3413B-2016 BOLT MACHINE - HEXAGON HEAD PD SHANK UNS N07718 185 KSI 1900-32 UNJF-3A (STRESS RUPTURE RESISTANT).pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、AEROSPACE STANDARDBOLT, MACHINE - HEXAGON HEAD, PD SHANK UNS N07718, 185 KSI, .1900-32 UNJF-3A(STRESS RUPTURE RESISTANT)AS3413Copyright 2016 SAE InternationalAll rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means,

2、electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA)Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.orgISSUED19

3、85-12REVISED2016-09THIRD ANGLE PROJECTIONCUSTODIAN: E-25REV.BFEDERAL SUPPLY CLASS5306AS3413SHEET 1 OF 3REV.BPROCUREMENT SPECIFICATION: AS7467, SEE NOTE /3/SAE Technical StandardsBoardRulesprovidethat:“ThisreportispublishedbySAE toadvancethestateoftechnicalandengineering sciences. Theuse of thisrepor

4、t isentirelyvoluntary, andits applicability andsuitability for any particularuse, includingany patent infringement arising therefrom,isthe soleresponsibility of theuser.”SAE reviewseachtechnical reportatleasteveryfiveyearsatwhichtimeitmayberevised,reaffirmed,stabilized,orcancelled.SAEinvites yourwri

5、tten comments andsuggestions.SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS3413BRATIONALECORRECT NOTE 1 FOR DATUMS ON SHORT LENGTH BOLTS, REVISE ACROSS POINTS DIMENSION, UPDATE STRAIGHTNESS FCF, ADD EDGE DISTANCE EXCEPTION FO

6、R HEAD MARKING. ADD AS3062, CHANGE END CHAMFER ANGLE FROM REF TO APPROX. ADD SURFACE TEXTURE REQUIREMENT TO WRENCH FLATS, ADD RUNOUT REQUIREMENT TO EDGE OF BEARING SURFACE, ADD EXISTING INVENTORY USE NOTE. UPDATE FPI REQUIREMENT, FIGURE 1 RE-DRAWN, GENERAL EDITORIAL UPDATE.FIGURE 1 BOLTAEROSPACE STA

7、NDARDAS3413SHEET 2 OF 3REV.BBOLT, MACHINE - HEXAGON HEAD, PD SHANK UNS N07718, 185 KSI, .1900-32 UNJF-3A(STRESS RUPTURE RESISTANT)TABLE 1 - DIMENSIONSPARTNUMBER LGMINKMAXAPPROX MASSLBS/100AS3413-03AS3413-04AS3413-05AS3413-06AS3413-07AS3413-08AS3413-09AS3413-10AS3413-11AS3413-12AS3413-13AS3413-14AS34

8、13-15AS 3413-16AS3413-17AS3413-18AS3413-19AS3413-20AS3413-21AS3413-22AS3413-23AS3413-24AS3413-25AS3413-26AS3413-27AS3413-28AS3413-29AS3413-30AS3413-31AS3413-32AS3413-33AS3413-34AS3413-35AS3413-36AS3413-37AS3413-38AS3413-39AS3413-40AS3413-41AS3413-42AS3413-43AS3413-44AS3413-45.302- .322.365- .385.428

9、- .448.490- .510.552- .572.615- .635.678- .698.740- .760.802- .822.865- .885.928- .948.990-1.0101.052-1.0721.115-1.1351.178-1.1981.240-1.2601.302-1.3221.365-1.3851.428-1.4481.490-1.5101.552-1.5721.615-1.6351.678-1.6981.740-1.7601.802-1.8221.865-1.8851.928-1.9481.990-2.0102.115-2.1352.240-2.2602.365-

10、2.3852.490-2.5102.615-2.6352.740-2.6352.865-2.8852.990-3.0103.115-3.1353.240-3.2603.365-3.3853.490-3.5103.615-3.6353.740-3.7603.865-3.885.025.025.025.025.025.025.025.025.060.123.186.248.310.373.436.498.560.623.686.748.810.873.936.9981.0601.1231.1861.2481.3731.4981.6231.7481.8731.9982.1232.2482.3732.

11、4982.6232.7482.8732.9983.123.092.092.092.092.092.092.092.120.183.245.308.370.432.495.558.620.682.745.808.870.932.9951.0581.1201.1821.2451.3081.3701.4951.6201.7451.8701.9952.1202.2452.3702.4952.6202.7452.8702.9953.1203.245.59.63.67.71.76.80.84.88.92.961.001.041.091.141.181.221.261.301.341.391.431.471

12、.511.551.591.641.681.731.811.891.982.062.142.222.322.402.482.572.652.732.822.912.99AEROSPACE STANDARDAS3413SHEET 3 OF 3REV.BBOLT, MACHINE - HEXAGON HEAD, PD SHANK UNS N07718, 185 KSI, .1900-32 UNJF-3A(STRESS RUPTURE RESISTANT)NOTES/1/ FOR PART NUMBERS AS3413-03 THRU AS3413-14 DATUM A SHALL REPLACE D

13、ATUM B.2. MATERIAL: CORROSION AND HEAT RESISTANT NICKEL ALLOY AMS5662 (UNS N07718)./3/ PROCUREMENT SPECIFICATION: AS7467 EXCEPT ROLL THREAD AND COLD WORK FILLET RADIUS AFTER PRECIPITATION HARDENING.4. FLUORESCENT PENETRANT INSPECTION PER ASTM E1417/E1417M TYPE 1, SENSITIVITY LEVEL 2 MINIMUM.5. SURFA

14、CE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1 UNLESS OTHERWISE SPECIFIED, SURFACES TO BE 125 MICROINCHES Ra, EXCEPT UPSET HEAD TO BE 250 MICROINCHES Ra.6. BREAK SHARP EDGES .003 TO .015 UNLESS OTHERWISE STATED.7. DIMENSIONS IN INCHES.8. DIMENSIONING AND TOLERANCING PER ANSI Y14.5

15、M-1982 (ASME PUBLICATION).9. UNLESS OTHERWISE SPECIFIED, PART INVENTORY MANUFACTURED TO PREVIOUS REVISIONS OF THE APPLICABLE DRAWINGOR SPECIFICATION MAY BE PROCURED AND USED UNTIL STOCK IS DEPLETED.10. DO NOT USE UNASSIGNED PART NUMBERS.11. REVISION INDICATOR: A CHANGE BAR (I) LOCATED IN THE LEFT MA

16、RGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THISDOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS.ASME IS AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION.ASTM IS ASTM INTERNATIONAL PUBLICATION.