SAE AS 3404A-2015 BOLT MACHINE - HEXAGON HEAD DRILLED 6 HOLES PD SHANK AMS5708 (UNS N07001) 1900-32 UNJF-3A.pdf

《SAE AS 3404A-2015 BOLT MACHINE - HEXAGON HEAD DRILLED 6 HOLES PD SHANK AMS5708 (UNS N07001) 1900-32 UNJF-3A.pdf》由会员分享，可在线阅读，更多相关《SAE AS 3404A-2015 BOLT MACHINE - HEXAGON HEAD DRILLED 6 HOLES PD SHANK AMS5708 (UNS N07001) 1900-32 UNJF-3A.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、AEROSPACE STANDARDBOLT, MACHINE - HEXAGON HEAD, DRILLED 6 HOLES, PD SHANK, AMS5708 (UNS N07001), .1900-32 UNJF-3AAS3404Copyright 2015 SAE InternationalAll rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electro

2、nic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA)Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.orgISSUED1985-08 R

3、EAFFIRMED2006-10 REVISED2015-08THIRD ANGLE PROJECTIONCUSTODIAN: E-25REV.AFEDERAL SUPPLY CLASS5306AS3404SHEET 1 OF 2REV.APROCUREMENT SPECIFICATION: AS7471SAE Technical StandardsBoardRulesprovidethat:“ThisreportispublishedbySAE toadvancethestateoftechnicalandengineering sciences. The use of thisreport

4、 isentirelyvoluntary, andits applicability andsuitability for any particularuse, includingany patent infringement arising therefrom,isthe soleresponsibility of theuser.”SAE reviewseachtechnical reportatleasteveryfiveyearsatwhichtimeitmayberevised,reaffirmed,stabilized,orcancelled.SAEinvites yourwrit

5、ten comments andsuggestions.SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS3404ARATIONALEUPDATE THREAD SPECIFICATION TO AS8879, UPDATE TO ANSI Y14.5M-1982, REVISE FPI REQUIREMENTS TO ASTM E1417/E1417M, ADD EDGE DISTANCE EXCEPT

6、ION FOR HEAD MARKING, REVISE ACROSS POINTS DIMENSION, ADD AS3062 FOR THREAD RUNOUT, FIGURE 1 REDRAWN, UPDATE REFERENCES, AND GENERAL EDITORIAL UPDATE.FIGURE 1 - BOLTAEROSPACE STANDARDAS3404SHEET 2 OF 2REV.ABOLT, MACHINE - HEXAGON HEAD, DRILLED 6 HOLES, PD SHANK, AMS5708 (UNS N07001), .1900-32 UNJF-3

7、ATABLE 1 - PART NUMBERS AND DIMENSIONSPART NO. LGMINKMAXAPPROX.MASSLB/100 PART NO. LGMINKMAXAPPROX.MASSLB/100AS3404-03 .302- .322 .025 .092 .79 AS3404-27 1.802-1.822 1.060 1.182 1.79AS3404-04 .365- .385 .025 .092 .83 AS3404-28 1.865-1.885 1.123 1.245 1.83AS3404-05 .428- .448 .025 .092 .87 AS3404-29

8、1.928-1.948 1.186 1.308 1.87AS3404-06 .490- .510 .025 .092 .91 AS3404-30 1.990-2.010 1.248 1.370 1.91AS3404-07 .552- .572 .025 .092 .95 AS3404-31 2.115-2.135 1.373 1.495 2.00AS3404-08 .615- .635 .025 .092 .99 AS3404-32 2.240-2.260 1.498 1.620 2.08AS3404-09 .678- .698 .025 .092 1.03 AS3404-33 2.365-2

9、.385 1.623 1.745 2.17AS3404-10 .740- .760 .025 .120 1.08 AS3404-34 2.490-2.510 1.748 1.870 2.26AS3404-11 .802- .822 .060 .183 1.12 AS3404-35 2.615-2.635 1.873 1.995 2.34AS3404-12 .865- .885 .123 .245 1.16 AS3404-36 2.740-2.760 1.998 2.120 2.42AS3404-13 .928- .948 .186 .308 1.20 AS3404-37 2.865-2.885

10、 2.123 2.245 2.50AS3404-14 .990-1.010 .248 .370 1.24 AS3404-38 2.990-3.010 2.248 2.370 2.59AS3404-15 1.052-1.072 .310 .432 1.28 AS3404-39 3.115-3.135 2.373 2.495 2.68AS3404-16 1.115-1.135 .373 .495 1.32 AS3404-40 3.240-3.260 2.498 2.620 2.76AS3404-17 1.178-1.198 .436 .558 1.37 AS3404-41 3.365-3.385

11、2.623 2.745 2.85AS3404-18 1.240-1.260 .498 .620 1.41 AS3404-42 3.490-3.510 2.748 2.870 2.93AS3404-19 1.302-1.322 .560 .682 1.45 AS3404-43 3.615-3.635 2.873 2.995 3.01AS3404-20 1.365-1.385 .623 .745 1.49 AS3404-44 3.740-3.760 2.998 3.120 3.09AS3404-21 1.428-1.448 .686 .808 1.53 AS3404-45 3.865-3.885

12、3.123 3.245 3.18AS3404-22 1.490-1.510 .748 .870 1.58AS3404-23 1.552-1.572 .810 .932 1.62AS3404-24 1.615-1.635 .873 .995 1.67AS3404-25 1.678-1.698 .936 1.058 1.71AS3404-26 1.740-1.760 .998 1.120 1.75NOTES:/1/ FOR PART NUMBERS AS3404-03 THRU AS3404-14 DATUM A SHALL REPLACE DATUM B.2. MATERIAL: AMS5708

13、 CORROSION AND HEAT RESISTANT NICKEL ALLOY (COMPOSITION SIMILAR TO UNS N07001).3. PROCUREMENT SPECIFICATION: AS7471.4. FLUORESCENT PENETRANT INSPECTION PER ASTM E1417/E1417M, TYPE 1, SENSITIVITY LEVEL 2 MIN.5. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE S

14、PECIFIED, SURFACES TO BE 125 MICROINCHES Ra. EXCEPT UPSET HEAD TO BE 250 MICROINCHES Ra.6. BREAK SHARP EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED.7. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: ANGULAR DIMENSIONS 5.8. DIMENSIONS AND TOLERANCING ANSI Y14.5M-1982 (ASME PUBLICATION)

15、.9. DO NOT USE UNASSIGNED PART NUMBERS.10. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICAT

16、ES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THATCONTAIN EDITORIAL CHANGES ONLY.AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS.ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION.ASTM IS AN ASTM INTERNATIONAL PUBLICATION.