SAE AS 33221-2013 GASKET CONDUCTIVE MIL-C-81511 ELECTRICAL CONNECTORS JAM NUT MOUNT《锁紧螺母座导电垫圈电连接器MIL-C-81511 n n》.pdf

《SAE AS 33221-2013 GASKET CONDUCTIVE MIL-C-81511 ELECTRICAL CONNECTORS JAM NUT MOUNT《锁紧螺母座导电垫圈电连接器MIL-C-81511 n n》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 33221-2013 GASKET CONDUCTIVE MIL-C-81511 ELECTRICAL CONNECTORS JAM NUT MOUNT《锁紧螺母座导电垫圈电连接器MIL-C-81511 n n》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、AEROSPACE STANDARD GASKET, CONDUCTIVE, MIL-C-81511 ELECTRICAL CONNECTORS, JAM NUT MOUNT AS33221Copyright 2013 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photoc

2、opying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2013-07THIRD ANGLE PROJECTIO

3、N CUSTODIAN: AE-8/AE-8C1 FEDERAL SUPPLY CLASS 5935 AS33221SHEET 1 OF 2PROCUREMENT SPECIFICATION: MIL-C-81511SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report is entirely voluntary, andits appl

4、icability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised, reaffirmed, stabilized, orcancelled. SAE invites yourwrittencomments andsu

5、ggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS33221RATIONALE AS33221 PERMITS THE CANCELLATION AND SUPERSESSION OF MS3322 WITH THIS DOCUMENT. FIGURE 1 - GASKET CONFIGURATION AEROSPACE STANDARD AS33221SHEET 2 OF 2GAS

6、KET, CONDUCTIVE, MIL-C-81511 ELECTRICAL CONNECTORS, JAM NUT MOUNT TABLE 1 - GASKET DIAMETER DIMENSIONS DASH NUMBER SHELL SIZE (REF) A DIAMETER -8 8 .731 (18.57) .725 (18.42 -10 10 .856 (21.74) .850 (21.59) -14 14 1.106 (28.09) 1.100 (27.94) -16 16 1.231 (31.27) 1.225 (31.12) -18 18 1.366 (34.70) 1.3

7、60 (34.54) -20 20 1.491 (37.87) 1.485 (37.72) -22 22 1.616 (41.05) 1.610 (40.89) -24 24 1.741 (44.22) 1.735 (44.07) REQUIREMENTS: 1. DIMENSIONS ARE IN INCHES. METRIC EQUIVALENTS ARE IN PARENTHESES ARE GIVEN FOR GENERAL INFORMATION ONLY AND BASED UPON 1 INCH = 25.4 MILLIMETERS. 2. THIS GASKET IS TO B

8、E USED WITH JAM NUT RECEPTACLES CONFORMING TO MIL-C-81511. 3. PART NUMBER EXAMPLE: MS3322 8 1 BASIC PART NUMBER DASH NUMBER (SEE TABLE 1) MATERIAL CODE (-1 IS CONDUCTIVE RUBBER, VOLUME RESISTIVITY 10 X 10-3 OHM-CM, TEMPERATURE RANGE -55 TO +200 C) APPLICATION NOTES: 1. THIS GASKET IS TO BE USED BETW

9、EEN THE CONNECTOR FLANGE AND THE PANEL, IN PLACE OF THE NONCONDUCTIVE “O” RING WHERE ELECTRICAL BONDING BETWEEN THE CONNECTOR AND THE PANEL/CHASSIS IS REQUIRED. SPECIFICATION NOTES: 1. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL RE

10、VISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.