SAE AS 3239E-2017 BOLT MACHINE C DOUBLE HEXAGON EXTENDED WASHER HEAD PD SHANK NICKEL ALLOY UNS N07718 185 KSI MIN 3750-24 UNJF-3A.pdf

《SAE AS 3239E-2017 BOLT MACHINE C DOUBLE HEXAGON EXTENDED WASHER HEAD PD SHANK NICKEL ALLOY UNS N07718 185 KSI MIN 3750-24 UNJF-3A.pdf》由会员分享，可在线阅读，更多相关《SAE AS 3239E-2017 BOLT MACHINE C DOUBLE HEXAGON EXTENDED WASHER HEAD PD SHANK NICKEL ALLOY UNS N07718 185 KSI MIN 3750-24 UNJF-3A.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、AEROSPACE STANDARDBOLT, MACHINE DOUBLE HEXAGON EXTENDEDWASHER HEAD, PD SHANK, NICKEL ALLOYUNS N07718, 185 KSI MIN, .3750-24 UNJF-3AAS3239Copyright 2017 SAE InternationalAll rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by

2、any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA)Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.

3、orgISSUED1980-07 REAFFIRMED2007-06 REVISED2017-03THIRD ANGLE PROJECTIONCUSTODIAN: E-25REV.EFEDERAL SUPPLY CLASS5306AS3239SHEET 1 OF 3REV.EPROCUREMENT SPECIFICATION: AS7466SAE Technical StandardsBoardRulesprovidethat:“ThisreportispublishedbySAE toadvancethestateoftechnicalandengineering sciences. The

4、 use of thisreport isentirelyvoluntary, andits applicability andsuitability for any particularuse, includingany patent infringement arising therefrom,isthe soleresponsibility of theuser.”SAE reviewseachtechnical reportatleasteveryfiveyearsatwhichtimeitmayberevised,reaffirmed,stabilized,orcancelled.S

5、AEinvites yourwritten comments andsuggestions.SAE values your input. To provide feedback on thisTechnical Report, please visit HTTP:/STANDARDS.SAE.ORG/AS3239ERATIONALEDELETE RADIUS AT TRANSITION OF WRENCH FLATS AND BASE FLANGE, ADD NEW INVENTORY DISPOSITION NOTE, ADD “MINIMUM“ TO FPI SENSITIVITY LEV

6、EL REQUIREMENT, GENERAL EDITORIAL UPDATE.FIGURE 1 BOLTAEROSPACE STANDARDAS3239SHEET 2 OF 3REV.EBOLT, MACHINE DOUBLE HEXAGON EXTENDEDWASHER HEAD, PD SHANK, NICKEL ALLOYUNS N07718, 185 KSI MIN, .3750-24 UNJF-3ATABLE 1 PART NUMBERS AND DIMENSIONSPART NO. LNMINMMAXAPPROXMASSLB/100 PART NO. LNMINMMAXAPPR

7、OXMASSLB/100AS3239-03 .552- .572 .025 .108 3.06 AS3239-33 2.865-2.885 1.732 1.875 9.61AS3239-04 .615- .635 .025 .108 3.24 AS3239-34 2.990-3.010 1.857 2.000 9.97AS3239-05 .678- .698 .025 .108 3.42 AS3239-35 3.115-3.135 1.982 2.125 10.32AS3239-06 .740- .760 .025 .108 3.59 AS3239-36 3.240-3.260 2.107 2

8、.250 10.67AS3239-07 .802- .822 .025 .108 3.77 AS3239-37 3.365-3.385 2.232 2.375 11.03AS3239-08 .865- .885 .025 .108 3.94 AS3239-38 3.490-3.510 2.357 2.500 11.39AS3239-09 .928- .948 .025 .108 4.12 AS3239-39 3.615-3.635 2.482 2.625 11.74AS3239-10 .990-1.010 .025 .108 4.30 AS3239-40 3.740-3.760 2.607 2

9、.750 12.09AS3239-11 1.052-1.072 .025 .108 4.47 AS3239-41 3.865-3.885 2.732 2.875 12.45AS3239-12 1.115-1.135 .025 .125 4.65 AS3239-42 3.990-4.010 2.857 3.000 12.80AS3239-13 1.178-1.198 .045 .188 4.83 AS3239-43 4.115-4.135 2.982 3.125 13.15AS3239-14 1.240-1.260 .107 .250 5.00 AS3239-44 4.240-4.260 3.1

10、07 3.250 13.50AS3239-15 1.302-1.322 .169 .312 5.19 AS3239-45 4.365-4.385 3.232 3.375 14.87AS3239-16 1.365-1.385 .232 .375 5.37 AS3239-46 4.490-4.510 3.357 3.500 14.22AS3239-17 1.428-1.448 .295 .438 5.54 AS3239-47 4.615-4.635 3.482 3.625 14.57AS3239-18 1.490-1.510 .357 .500 5.72 AS3239-48 4.740-4.760

11、 3.607 3.750 14.93AS3239-19 1.552-1.572 .419 .562 5.90 AS3239-49 4.865-4.885 3.732 3.875 15.28AS3239-20 1.615-1.635 .482 .625 6.07 AS3239-50 4.990-5.010 3.857 4.000 15.63AS3239-21 1.678-1.698 .545 .688 6.25 AS3239-51 5.115-5.135 3.982 4.125 15.99AS3239-22 1.740-1.760 .607 .750 6.43 AS3239-52 5.240-5

12、.260 4.107 4.250 16.34AS3239-23 1.802-1.822 .669 .812 6.60 AS3239-53 5.365-5.385 4.232 4.375 16.70AS3239-24 1.865-1.885 .732 .875 6.78 AS3239-54 5.490-5.510 4.357 4.500 17.05AS3239-25 1.928-1.948 .795 .938 6.96 AS3239-55 5.615-5.635 4.482 4.625 17.39AS3239-26 1.990-2.010 .857 1.000 7.13 AS3239-56 5.

13、740-5.760 4.607 4.750 17.73AS3239-27 2.115-2.135 .982 1.125 7.48 AS3239-57 5.865-5.885 4.732 4.875 18.07AS3239-28 2.240-2.260 1.107 1.250 7.84 AS3239-58 5.990-6.010 4.857 5.000 18.41AS3239-29 2.365-2.385 1.232 1.375 8.20AS3239-30 2.490-2.510 1.357 1.500 8.55AS3239-31 2.615-2.635 1.482 1.625 8.91AS32

14、39-32 2.740-2.760 1.607 1.750 9.26AEROSPACE STANDARDAS3239SHEET 3 OF 3REV.EBOLT, MACHINE DOUBLE HEXAGON EXTENDEDWASHER HEAD, PD SHANK, NICKEL ALLOYUNS N07718, 185 KSI MIN, .3750-24 UNJF-3ANOTES/1/ FOR PART NUMBERS AS3239-03 THROUGH AS3239-21, DATUM Z SHALL REPLACE DATUM Y.2. MATERIAL: CORROSION AND

15、HEAT RESISTANT NICKEL ALLOY PER AMS5662 (UNS N07718).3. PROCUREMENT SPECIFICATION: AS7466.4. FLUORESCENT PENETRANT INSPECTION BEFORE PLATING PER ASTM E1417/E1417M, TYPE 1, SENSITIVITY LEVEL 2, MINIMUM.5. SURFACE TEXTURE: SYMBOLS ARE PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPE

16、CIFIED,SURFACES TO BE 125 MICROINCHES Ra.6. BREAK SHARP EDGES .003 TO .015, UNLESS OTHERWISE SPECIFIED.7. DIMENSIONS ARE IN INCHES.8. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M-1982 (ASME PUBLICATION).9. UNLESS OTHERWISE SPECIFIED, PART INVENTORY MANUFACTURED TO PREVIOUS REVISIONS OF THE APPLICABL

17、E DRAWING OR SPECIFICATION MAY BE PROCURED AND USED UNTIL STOCK IS DEPLETED.10. DO NOT USE UNASSIGNED PART NUMBERS.11. REVISION INDICATOR: A CHANGE BAR (I) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE

18、 TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS.ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION.ASTM IS AN ASTM INTERNATIONAL PUBLICATION.