SAE AS 1910C-2003 Hose Assembly Polytetrafluoroethylene CRES Reinforced 400 F 3000 psi Lightweight Beam Seal Straight to 45《180对45光束密封轻质400 F、3000 psi、CRES加固的聚四氟乙烯软管组件》.pdf

《SAE AS 1910C-2003 Hose Assembly Polytetrafluoroethylene CRES Reinforced 400 F 3000 psi Lightweight Beam Seal Straight to 45《180对45光束密封轻质400 F、3000 psi、CRES加固的聚四氟乙烯软管组件》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 1910C-2003 Hose Assembly Polytetrafluoroethylene CRES Reinforced 400 F 3000 psi Lightweight Beam Seal Straight to 45《180对45光束密封轻质400 F、3000 psi、CRES加固的聚四氟乙烯软管组件》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、SAE Technical Standards Board Rules providethat: “This report is published by SAE to advancethe state oftechnical and engineering sciences.Theuse ofthis reportisentirelyvoluntary, andits applicabilityand suitabilityfor any particularuse,including any patentinfringement arising therefrom,isthe sole r

2、esponsibility of the user.”SAE reviews each technical reportatleastevery five years atwhich timeitmay bereaffirmed,revised, or cancelled.SAE invites yourwritten comments and suggestions.SHEET 1 OF 5AS1910REV.CCopyright 2003 Society of Automotive Engineers, Inc.All rights reserved. No part of this pu

3、blication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, orotherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (out

4、side USA)Fax: 724-776-0790 Email: custsvcsae.org SAE WEB ADDRESS: http:/www.sae.orgAEROSPACE STANDARDAS1910REV.CISSUED 1985-08 REVISED 2003-02(R) HOSE ASSEMBLY, POLYTETRAFLUOROETHYLENE,CRES REINFORCED, 400 F, 3000 PSI, LIGHTWEIGHT,BEAM SEAL, STRAIGHT TO 45CUSTODIAN: SAE G-3/G-3D PROCUREMENT SPECIFIC

5、ATION: /13/ AS1339FEDERAL SUPPLY CLASS 4720FIGURE 1 - HOSE AND FITTING DIMENSIONSFIGURE 2 - FITTINGS(ENLARGED VIEW)FIGURE 3 - ABRASION SLEEVE RETENTIONFIGURE 4 - ALTERNATE ELBOW CONFIGURATION /21/Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or netwo

6、rking permitted without license from IHS-,-HOSE ASSEMBLY, POLYTETRAFLUOROETHYLENE,CRES REINFORCED, 400 F, 3000 PSI, LIGHTWEIGHT,BEAM SEAL, STRAIGHT TO 45AEROSPACE STANDARDAS1910SHEET 2 OF 5AS1910REV.CREV. C(R)TABLE 1- HOSE AND FITTING DIMENSIONSHOSEASSEMBLYNO. ANDSIZE CODESIZEREFTHREAD TPER MIL-S-88

7、79REFA1MAXA2MAXB /2/DIAMINCHEXREFEMINEMAXAS1910-04 .250 .4375-24UNJS-3B 1.30 1.90 .135 .56 .450 .550AS1910-06 .375 .5625-20UNJS-3B 1.44 2.35 .240 .69 .517 .600AS1910-08 .500 .7188-20UNJS-3B 1.60 2.50 .340 .88 .513 .675AS1910-10 .625 .8438-18UNJS-3B 1.70 2.70 .410 1.00 .620 .765AS1910-12 .750 1.0000-

8、16UNJ-3B 1.85 3.15 .510 1.125 .760 .874AS1910-16 1.000 1.2500-14UNJS-3B 2.18 3.50 .760 1.50 .825 .950TABLE 2 - HOSE OR SLEEVE OUTSIDE DIAMETERSSLEEVECODE SLEEVE MATERIALTEMP.LIMITFHOSE ORSLEEVEOUTSIDEDIAMETERS(MAX-MIN)/4/.250HOSE ORSLEEVEOUTSIDEDIAMETERS(MAX-MIN)/4/.375HOSE ORSLEEVEOUTSIDEDIAMETERS(

9、MAX-MIN)/4/.500HOSE ORSLEEVEOUTSIDEDIAMETERS(MAX-MIN)/4/.625HOSE ORSLEEVEOUTSIDEDIAMETERS(MAX-MIN)/4/.750HOSE ORSLEEVEOUTSIDEDIAMETERS(MAX-MIN)/4/1.000 () INDICATES HOSE ONLYNO SLEEVE (SEE AS1339)40-A ABRASION SLEEVE TUBULAR /5/(TFE-AS1291-CODE B)400 .500/.440 .600/.540 .730/.670 .840/.7801.110/1.05

10、0 1.400/1.340B ABRASION SLEEVE COIL /6/(NYLON AS1294)275 .450/.390 .550/.490 .695/.635 .810/.7501.080/1.020 1.360/1.300C FIRESLEEVE (AS1072 SIL-FG)(15 min) /7/ /8/ /11/400 .625/.500 .750/.625 .875/.750 1.000/.8751.250/1.125 1.500/1.375E ABRASION SLEEVE SHRINK-ON(FEP) (M23053/11) /10/350 .424/.374 .5

11、40/.480 .665/.615 .790/.7301.070/1.010 1.350/1.290F ABRASION SLEEVE SHRINK-ON(POLYOLEFIN AS1073 - CODE B)/11/275 .450/.400 .560/.505 .695/.645 .810/.7501.080/1.020 1.360/1.300H FIRESLEEVE INTEGRAL SILICONE(15 min) /11/ /12/400 .660/.600 .745/.685 .895/.835 1.005/.9451.240/1.160 1.515/1.455K INTEGRAL

12、 ABRASION SLEEVE /9/(BRAIDED) POLYESTER300 .490/.444 .570/.535 .695/.650 .800/.7601.070/1.030 1.350/1.310L ABRASION SLEEVE COIL /6/(PTFE-AS1293)400 .500/.440 .600/.540 .730/.670 .862/.8021.110/1.050 1.400/1.340TABLE 3 - HOSE ASSEMBLY LENGTH TOLERANCESHOSE ASSEMBLY LENGTH TOLERANCEUNDER 18 in .125 in

13、18 TO 36 in EXCLUSIVE .250 in36 TO 50 in EXCLUSIVE .500 in50 in AND OVER 1%Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-HOSE ASSEMBLY, POLYTETRAFLUOROETHYLENE,CRES REINFORCED, 400 F, 3000 PSI, LIGHT

14、WEIGHT,BEAM SEAL, STRAIGHT TO 45AEROSPACE STANDARDAS1910SHEET 3 OF 5AS1910REV.CREV. C(R)TABLE 4 - WEIGHTSHOSEORSLEEVECODE HOSE OR TYPE SLEEVE UNITSREFERENCEWEIGHTLB/IN/22/HOSESIZE.250REFERENCEWEIGHTLB/IN/22/HOSESIZE.375REFERENCEWEIGHTLB/IN/22/HOSESIZE.500REFERENCEWEIGHTLB/IN/22/HOSESIZE.625REFERENCE

15、WEIGHTLB/IN/22/HOSESIZE.750REFERENCEWEIGHTLB/IN/22/HOSESIZE1.000-ABHOSE ONLYABRASION SLEEVE(TFE-AS1291-B)ABRASION SLEEVE(NYLON AS1294)LB/INLB/INLB/IN.009.003.001.015.004.002.020.004.003.027.005.003.058.007.004.085.009.005CEFFIRESLEEVE (15 min)AS1072ABRASION SLEEVE(FEP)ABRASION SLEEVE(AS1073B)LB/INLB

16、/INLB/IN.007.002.002.009.003.003.011.003.003.012.005.004.017.006.005.021.007.006HKLFIRESLEEVE INTEGRAL(15 min) ON HOSEABRASION SLEEVEPOLYESTER WITHHOSEABRASION SLEEVE(PTFE-AS1293)LB/INLB/INLB/IN.019.012.003.027.016.004.035.022.005.047.030.005.099.060.006.117.090.007NONE FIRESLEEVE CLAMP/23/LB/EA .02

17、5 .025 .025 .026 .026 .033NONE FITTING END(STRAIGHT) /23/LB/EA .060 .088 .142 .225 .355 .530NONE FITTING END (45)/23/LB/EA .065 .095 .160 .240 .420 .700TABLE 5 - SLEEVE LENGTHSHOSE SIZE LENGTH (in).250/.375.500/.625.750/1.0002.00 .252.50 .253.00 .25TABLE 6 - SPHERICAL BALL SIZE FOR DETERMININGMINIMU

18、M HOSE ASSEMBLY ID /2/HOSE SIZE STRAIGHT FITTING ELBOW FITTING040608.122.216.306.115.204.289101216.369.459.684.349.434.646Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-HOSE ASSEMBLY, POLYTETRAFLUOROE

19、THYLENE,CRES REINFORCED, 400 F, 3000 PSI, LIGHTWEIGHT,BEAM SEAL, STRAIGHT TO 45AEROSPACE STANDARDAS1910SHEET 4 OF 5AS1910REV.CREV. C(R)NOTES:/1/ LENGTH “L” IS A FOUR DIGIT NUMBER OF WHICH THE FIRST THREE DIGITS DESCRIBE THE HOSE ASSEMBLY LENGTH IN WHOLE INCHES, AND THE FOURTH DIGIT, THE FRACTION OF

20、AN INCH IN EIGHTHS. LENGTH “L” IS MEASURED FROM OUTER CORNER OF SEALING SURFACE TO OUTER CORNER OF SEALING SURFACE AS SHOWN IN FIGURE 1. FOR LENGTH INCREMENTS AND TOLERANCES SEE TABLE 3./2/ A TRUE CIRCULAR CROSS SECTION IS NOT REQUIRED THROUGH THE FITTING I.D. HOWEVER, THE APPLICABLE BALL DIAMETER L

21、ISTED IN TABLE 6 SHALL PASS THROUGH THE END FITTING AFTER IT IS ASSEMBLED TO THE HOSE. DISTANCE ACROSS CORNERS OF THE COUPLING NUT MAY EXCEED THIS DIMENSION./3/ STANDARD COUPLING NUTS SHALL MATE WITH MIL-F-85421 FITTING ENDS. NONSTANDARD COUPLING NUTS MAY BE USED, PROVIDED THEY ARE DIMENSIONALLY AND

22、 FUNCTIONALLY EQUIVALENT AND PROVIDED THEY CANNOT BE REMOVED FROM THE FITTING. NUTS SHALL MEET TORQUE TEST REQUIREMENTS PER AS1339 EXCEPT TORQUE VALUES SHALL BE PER MIL-F-85421. THE THREAD AND ALL INTERNAL SURFACES SHALL BE DRY-FILM LUBRICATED WITH MIL-PRF-46010 TYPE I COATING. ALL EXTERNAL SURFACES

23、 MAY BE DRY-FILM COATED./4/ DIAMETERS ARE LISTED FOR CLAMP SELECTION. TUBULAR SLEEVES MAY NOT BE A PERFECT ROUND AND SHALL BE MEASURED WITH A DIAMETER TAPE RULER (OFTEN REFERRED TO AS PI-TAPE)./5/ TUBULAR ABRASION (TFE) SLEEVES SHALL HAVE AN I.D. NO GREATER THAN HOSE O.D. +.05 in. AXIAL MOVEMENT OF

24、THE SLEEVE INSTALLED ON THE HOSE SHALL NOT EXCEED .05 in. ENDS OF THE TUBULAR SLEEVE SHALL BE TERMINATED WITH A LENGTH OF M23053/11 (FEP) CLASS 1 OR 2, COLOR CLEAR, PER TABLE 5 AND FIGURE 3./6/ COIL ABRASION SLEEVES, WHEN ASSEMBLED ON A STRAIGHT HOSE, SHALL HAVE AN AVERAGE GAP BETWEEN COILS NOT EXCE

25、EDING .05 in. DISPLACEMENT OF THE COILS OF THE SLEEVE, CAUSING A GREATER GAP, SHALL NOT BE CAUSE FOR REJECTION IF THE COILS CAN BE REPOSITIONED TO MEET THE GAP REQUIREMENTS. ENDS OF THE COIL SLEEVE SHALL BE TERMINATED WITH A LENGTH OF HEAT SHRINKABLE SLEEVING IN ACCORDANCE WITH TABLE 5 AND FIGURE 3.

26、 CODE “B” (NYLON COIL) ABRASION SLEEVES SHALL BE TERMINATED WITH M23053/5, CLASS 1 OR 3, COLOR BLACK. CODE “L” (COIL ABRASION) SLEEVES SHALL BE TERMINATED WITH M23053/12A, CLASS 1, COLOR TRANSPARENT, PTFE. (OPTIONAL M23053/11 (FEP) CLASS 1 OR 2, COLOR CLEAR.)/7/ THE TABLE 2 SLEEVE DIAMETERS FOR AS10

27、72 SLEEVE APPLIES WHEN THE SLEEVE IS COMPRESSED, OR CLAMPED, TO CONTACT THE HOSE. IN THIS CASE A WRINKLE MAY OCCUR OVER APPROXIMATELY 10% OF THE SLEEVE CIRCUMFERENCE./8/ THE CUT ENDS OF THE FIRESLEEVE SHALL BE COATED WITH RTV SILICONE RUBBER, PRIOR TO INSTALLATION, TO PREVENT WICKING OF FLUIDS. THE

28、FIRESLEEVE ENDS SHALL BE SECURED TO THE HOSE ASSEMBLY END FITTINGS WITH CORROSION RESISTANT STEEL BANDS. AFTER INSTALLATION, CRACKS OR VOIDS IN THE FIRESLEEVE, WHICH EXPOSE THE FIBERGLASS, SHALL BE COATED WITH RTV SILICONE RUBBER./9/ INTEGRAL ABRASION SLEEVE SHALL FORM AN INTEGRAL, PERMANENT PART OF

29、 THE HOSE AND SHALL TERMINATE A MAXIMUM OF .200 in FROM THE END OF THE COLLAR./10/ FEP PER M23053/11 AND POLYOLEFIN PER AS1073-CODE B SHRINK ABRASION SLEEVES SHALL BE SHRUNK TO A SNUG FIT OVER THE HOSE AND END FITTING COLLARS./11/ ADD “AS1055 TYPE IIb CLASS B-S/P” OR “AS150 TYPE IX bB” TO IDENTIFICA

30、TION MARKING TO SHOW LEVEL OF COMPLIANCE. “FIRE-PROOF” (15 min) WITH AS1055./12/ THE ENDS OF THE INTEGRAL FIRESLEEVE AND FITTING SOCKET/COLLAR MAY BE COVERED WITH A SILICONE CUFF OR MOLDED AS REQUIRED TO COMPLY WITH /11/./13/ THIS HOSE ASSEMBLY SHALL BE QUALIFIED IN ACCORDANCE WITH PROCUREMENT SPECI

31、FICATION AS1339. USERS OF THIS STANDARD ARE ADVISED TO CONTROL SOURCE APPROVAL(S) BY STANDARD PAGE SUPPLEMENT SHEET OR SIMILAR MEANS.CHANGE-OVER FROM USER-QPL TO PRI-QPL SHALL BE PERFORMED IN ACCORDANCE WITH AS1339E AND COMPLETED BY MARCH 1, 2002. USERS OF THIS STANDARD SHALL PROCURE THE PRODUCT FRO

32、M ACCREDITED MANUFACTURERS, OR THEIR ACCREDITED DISTRIBUTORS, AS LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST PRI-QPL-AS1339 FOR THIS STANDARD.14. MATERIALS: HOSE AND FITTINGS - PER AS1339.15. CONSTRUCTION AND PERFORMANCE: AS1339 FITTINGS SHALL BE PERMANENTLY ATTACHED TO

33、THE HOSE.16. OPERATING CHARACTERISTICS: SEE AS1339.17. DIMENSIONING AND TOLERANCING: ANSI Y14.5M-1982.18. DIMENSIONS IN INCHES, UNLESS OTHERWISE SPECIFIED.TOLERANCES: LINEAR DIMENSIONS .010, ANGULAR DIMENSIONS 2.Copyright SAE International Provided by IHS under license with SAENot for ResaleNo repro

34、duction or networking permitted without license from IHS-,-HOSE ASSEMBLY, POLYTETRAFLUOROETHYLENE,CRES REINFORCED, 400 F, 3000 PSI, LIGHTWEIGHT,BEAM SEAL, STRAIGHT TO 45AEROSPACE STANDARDAS1910SHEET 5 OF 5AS1910REV.CREV. C(R)19. MARKING SHALL BE PER AS1339 ON A STAINLESS STEEL BAND NOT OVER 1.0 in W

35、IDE, OR ON THE COLLAR, THE CHARACTERS SHALL BE A MINIMUM OF .063 in HIGH. THE BAND SHALL BE SO DESIGNED AS TO REMAIN TIGHT ON THE HOSE TO PREVENT RELATIVE MOVEMENT AND RESULTANT CHAFING. IT SHALL BE OF SUFFICIENT STRENGTH TO PREVENT REMOVAL BY HAND. HOSE ASSEMBLY DATE AND “PT” SYMBOL SHALL BE ELECTR

36、OETCHED OR STAMPED ON THE BAND OR ON AN END FITTING OR A FIRESLEEVE CLAMP./20/ LOCKWIRE HOLES, LOCATION, AND DIAMETER PER AS1043. LOCKWIRE HOLE DESIGNATION IS AS FOLLOWS:a. X = NONEb. U = TWO HOLES, 180 APARTc. W = THREE HOLES, 120 APART/21/ ALTERNATE FORGED CONFIGURATION MAY BE USED PROVIDED ALL DI

37、MENSIONAL AND WEIGHT REQUIREMENTS ARE MET.22. EXAMPLE OF PART NUMBER:/23/ FIRESLEEVE CLAMP AND FITTING END ARE IN POUNDS EACH.24. THE CHANGE BAR ( l ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT.Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-