SAE AS 1043G-2017 SAFETY WIRE HOLES HEX FITTING LOCATION OF DESIGN STANDARD.pdf

《SAE AS 1043G-2017 SAFETY WIRE HOLES HEX FITTING LOCATION OF DESIGN STANDARD.pdf》由会员分享，可在线阅读，更多相关《SAE AS 1043G-2017 SAFETY WIRE HOLES HEX FITTING LOCATION OF DESIGN STANDARD.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、AEROSPACE STANDARDSAFETY WIRE HOLES, HEX, FITTING,LOCATION OF, DESIGN STANDARDAS1043Copyright 2017 SAE InternationalAll rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, reco

2、rding, or otherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA)Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.orgISSUED1963-07REAFFIRMED 2013-01REVISED2017-05THIRD

3、 ANGLE PROJECTIONCUSTODIAN: G-3REV. GFEDERAL SUPPLY CLASS4720AS1043SHEET 1 OF 5REV.GPROCUREMENT SPECIFICATION: NONESAE Technical Standards BoardRules providethat:“This reportis publishedbySAEtoadvance thestateoftechnical andengineering sciences. The useofthis reportisentirely voluntary, and its appl

4、icability and suitability forany particularuse, includingany patent infringement arising therefrom,is thesole responsibility of theuser.”SAE reviews eachtechnical reportatleastevery fiveyears at whichtime it mayberevised, reaffirmed, stabilized, or cancelled. SAEinvites your written comments and sug

5、gestions.SAE values your input. To provide feedback on thisTechnical Report, please visit HTTP:/STANDARDS.SAE.ORG/AS1043GRATIONALETABLE 1 REDRAWIN FOR CLARITY, AMENDED VARIOUS DIMENSIONS FOR .375, .438, AND .500 ACROSS FLATS SIZES AND GENERAL UPDATES TO LATEST SAE STANDARDS.FIGURE 1 STYLE A /2/FIGUR

6、E 2 STYLE BFIGURE 3 STYLE CFIGURE 4 STYLE DFIGURE 5 STYLE EAEROSPACE STANDARD AS1043SHEET 2 OF 5REV.GSAFETY WIRE HOLES, HEX, FITTING,LOCATION OF, DESIGN STANDARDFIGURE 6 STYLE F /2/FIGURE 7 STYLE G /2/FIGURE 8 END VIEW (TYP)FIGURE 9 OPTIONAL CONFIGURATIONENLARGED END VIEW AAEROSPACE STANDARD AS1043S

7、HEET 3 OF 5REV.GSAFETY WIRE HOLES, HEX, FITTING,LOCATION OF, DESIGN STANDARDTABLE 1 DIMENSIONS A, B, AND C FOR ALL STYLESA B /4/ CACROSSFLATSSTYLEA, B, C, D, E, FSTYLEA, B, C, D, E, F QTYSTYLEG QTY.375 .030 .002 .028 + .004/-.001 2 - -.438 .030 .002 .028 + .004/-.001 2 .025 + .004/-.001 2.500 .057 .

8、005 .047 + .005/-.001 2 .025 + .004/-.001 2.562 .057 .005 .047 + .005/-.001 2 .047 + .005/-.001 2.625 .057 .005 .047 + .005/-.001 2 .047 + .005/-.001 2.688 .057 .005 .047 + .005/-.001 2 .047 + .005/-.001 2.750 .057 .005 .047 + .005/-.001 2 .047 + .005/-.001 2.813 .057 .005 .047 + .005/-.001 2 .047 +

9、 .005/-.001 2.875 .057 .005 .047 + .005/-.001 2 .070 .005 2.938 .078 .005 .047 + .005/-.001 2 .070 .005 21.000 .078 .005 .047 + .005/-.001 2 .070 .005 21.125 .110 .010 .070 .005 2 .070 .005 21.250 .110 .010 .070 .005 2 .070 .005 21.375 .110 .010 .070 .005 2 .070 .005 21.500 .110 .010 .070 .005 2 .07

10、0 .005 21.625 .110 .010 .070 .005 3 .070 .005 21.750 .110 .010 .070 .005 3 .070 .005 21.875 .110 .010 .070 .005 3 .070 .005 22.000 .110 .010 .070 .005 3 .070 .005 22.125 .110 .010 .070 .005 3 .070 .005 22.250 .110 .010 .070 .005 3 .070 .005 22.375 .110 .010 .070 .005 3 .070 .005 22.500 .110 .010 .07

11、0 .005 3 .070 .005 22.625 .110 .010 .070 .005 3 .070 .005 22.750 .110 .010 .070 .005 3 - -2.875 .110 .010 .070 .005 3 - -3.000 .110 .010 .070 .005 3 - -3.125 .110 .010 .070 .005 3 - -3.250 .110 .010 .070 .005 3 - -3.375 .110 .010 .070 .005 3 - -3.500 .110 .010 .070 .005 3 - -3.625 .110 .010 .070 .00

12、5 3 - -3.750 .110 .010 .070 .005 3 - -3.875 .110 .010 .070 .005 3 - -4.000 .110 .010 .070 .005 3 - -AEROSPACE STANDARD AS1043SHEET 4 OF 5REV.GSAFETY WIRE HOLES, HEX, FITTING,LOCATION OF, DESIGN STANDARDTABLE 1A DIMENSIONS A, D, E AND W FOR ALL STYLESA D E WACROSSFLATSSTYLEASTYLEB, D, ESTYLECSTYLEFST

13、YLEGSTYLEG WIDTH.375 .246 .015 W/2 .020 .250 .020 - .108 .020 - AS REQD.438 .276 .015 W/2 .020 .250 .020 .077 .020 .108 .020 .176 .010 AS REQD.500 .276 .015 W/2 .020 .250 .020 .079 .020 .108 .020 .238 .010 AS REQD.562 .276 .015 W/2 .020 .250 .020 .188 .020 .188 .020 .261 .010 AS REQD.625 .276 .015 W

14、/2 .020 .250 .020 .188 .020 .188 .020 .298 .010 AS REQD.688 .276 .015 W/2 .020 .250 .020 .188 .020 .188 .020 .334 .010 AS REQD.750 .276 .015 W/2 .020 .250 .020 .250 .020 .188 .020 - AS REQD.813 .276 .015 W/2 .020 .250 .020 .250 .020 .188 .020 - AS REQD.875 .293 .015 W/2 .020 .250 .020 .250 .020 .188

15、 .020 .423 .010 AS REQD.938 .293 .015 W/2 .020 .250 .020 .250 .020 .250 .020 - AS REQD1.000 .358 .015 W/2 .020 .250 .020 .250 .020 .250 .020 .495 .010 AS REQD1.125 .358 .005 W/2 .020 .250 .020 .250 .020 .250 .020 .567 .010 AS REQD1.250 .378 .015 W/2 .020 .250 .020 .281 .020 .250 .020 .640 .010 AS RE

16、QD1.375 .378 .015 W/2 .020 .250 .020 .281 .020 .250 .020 .702 .010 AS REQD1.500 .398 .015 W/2 .020 .250 .020 .281 .020 .250 .020 .774 .010 AS REQD1.625 .398 .015 W/2 .020 .250 .020 .281 .020 .250 .020 .849 .010 AS REQD1.750 .398 .015 W/2 .020 .250 .020 .281 .020 .250 .020 - AS REQD1.875 .398 .015 W/

17、2 .020 .250 .020 .281 .020 .250 .020 .990 .010 AS REQD2.000 .482 .015 W/2 .020 .250 .020 .281 .020 .281 .020 1.065 .010 AS REQD2.125 .482 .015 W/2 .020 .250 .020 .281 .020 .281 .020 1.138 .010 AS REQD2.250 .592 .015 W/2 .020 .250 .020 .281 .020 .281 .020 - AS REQD2.375 .592 .015 W/2 .020 .250 .020 .

18、281 .020 .281 .020 1.282 .010 AS REQD2.500 .592 .015 W/2 .020 .250 .020 .281 .020 .281 .020 - AS REQD2.625 .545 .015 W/2 .020 .250 .020 .281 .020 .312 .020 1.426 .010 AS REQD2.750 .545 .015 W/2 .020 .250 .020 .281 .020 .312 .020 - AS REQD2.875 .607 .015 W/2 .020 .250 .020 .281 .020 .312 .020 - AS RE

19、QD3.000 .607 .015 W/2 .020 .250 .020 .281 .020 .312 .020 - AS REQD3.125 .607 .015 W/2 .020 .250 .020 .281 .020 .312 .020 - AS REQD3.250 .607 .015 W/2 .020 .250 .020 .281 .020 .312 .020 - AS REQD3.375 .586 .015 W/2 .020 .250 .020 .281 .020 .312 .020 - AS REQD3.500 .586 .015 W/2 .020 .250 .020 .281 .0

20、20 .312 .020 - AS REQD3.625 .586 .015 W/2 .020 .250 .020 .281 .020 .312 .020 - AS REQD3.750 .586 .015 W/2 .020 .250 .020 .281 .020 .312 .020 - AS REQD3.875 .586 .015 W/2 .020 .250 .020 .281 .020 .312 .020 - AS REQD4.000 .627 .015 W/2 .020 .250 .020 .281 .020 .312 .020 - AS REQDAEROSPACE STANDARD AS1

21、043SHEET 5 OF 5REV.GSAFETY WIRE HOLES, HEX, FITTING,LOCATION OF, DESIGN STANDARDNOTES1. THIS DESIGN STANDARD ESTABLISHES HOLE SIZES AND LOCATION DIMENSIONS FOR SAFETY WIRE HOLES IN FITTINGS.2/ STYLE A APPLIES TO AN818, MS27073, AND AS4370. STYLE F APPLIES TO AS1790. STYLE G APPLIES TO NUTS FOR BEAM

22、SEAL FITTINGS.3. BREAK ALL SHARP EDGES OF THE SAFETY WIRE HOLE./4/ DIMENSION “B” IS MEASURED FROM THE INTERSECTING POINT OF HEX FLATS./5/ DIMENSION “E” IS MEASURED FROM THE CENTERLINE.6. DIMENSIONING AND TOLERANCING: ANSI Y14.5M-1982.7. DIMENSIONS ARE IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCE

23、S: LINEAR DIMENSIONS .010, ANGULAR DIMENSIONS 2.8. BREAK ALL SHARP EDGES .003 TO .015, UNLESS OTHERWISE SPECIFIED.9. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 MICROINCHES Ra.10. EXAMPLE OF CALLOUT “SAFETY WIRE HOLE

24、S PER AS1043 STYLE B”.11. REVISION INDICATOR: A CHANGE BAR (I) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THISDOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.