SAE AS 1001J-2017 FITTING TEE STANDARD AND REDUCER BULKHEAD ON RUN INTERNAL PORT ON SIDE FLARELESS.pdf

《SAE AS 1001J-2017 FITTING TEE STANDARD AND REDUCER BULKHEAD ON RUN INTERNAL PORT ON SIDE FLARELESS.pdf》由会员分享，可在线阅读，更多相关《SAE AS 1001J-2017 FITTING TEE STANDARD AND REDUCER BULKHEAD ON RUN INTERNAL PORT ON SIDE FLARELESS.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、 AEROSPACE STANDARD FITTING, TEE, STANDARD AND REDUCER, BULKHEAD ON RUN, INTERNAL PORT ON SIDE, FLARELESS AS1001Copyright 2017 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, m

2、echanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED1966-03REAFF

3、IRMED 2005-06REVISED2017-10THIRD ANGLE PROJECTION CUSTODIAN: G-3/G-3B REV.J FEDERAL SUPPLY CLASS 4730 AS1001 SHEET 1 OF 6 REV. J PROCUREMENT SPECIFICATION: AS18280 /4/ SAE Technical Standards Board Rules provide that: “This report is published by SAEtoadvance thestate of technicaland engineering sci

4、ences. The useof this report is entirely voluntary, and its applicability andsuitability for any particularuse, includingany patent infringement arisingtherefrom,is thesole responsibility of theuser.” SAE reviews eachtechnical reportatleast every fiveyears at whichtime it may be revised, reaffirmed,

5、 stabilized, or cancelled. SAE invites your written comments and suggestions.SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS1001J RATIONALE ADDED CONDUCTIVE HIGH PURITY ALUMINUM COATING FOR ALUMINUM ALLOY FITTINGS. FIGURE 1 - FITTING, TEE,

6、 BULKHEAD END FOR OPTIONAL USE IN PORT INSTALLATION, PORT #3 SHOWN AS NON-REDUCER FIGURE 2 - FITTING, TEE, BULKHEAD END FOR OPTIONAL USE IN PORT INSTALLATION, PORT #3 SHOWN AS REDUCER, SAME AS FIGURE 1 EXCEPT AS SHOWN AEROSPACE STANDARD AS1001 SHEET 2 OF 6 REV. J FITTING, TEE, STANDARD AND REDUCER,

7、BULKHEAD ON RUN, INTERNAL PORT ON SIDE, FLARELESS FIGURE 3 - FITTING, TEE, BULKHEAD END NOT FOR USE IN PORT INSTALLATION, PORT #3 SHOWN AS NON-REDUCER, SAME AS FIGURE 1 EXCEPT AS SHOWN FIGURE 4 - FITTING, TEE, BULKHEAD END NOT FOR USE IN PORT INSTALLATION, PORT #3 SHOWN AS REDUCER, SAME AS FIGURE 1

8、EXCEPT AS SHOWN TABLE 1 - DIMENSIONS AND WEIGHTS /16/ BASIC NO. AS1001 /13/ /25/ SIZE CODE E /12/ F / 12/ V W Z /14/ LB/EA APPROX REF ALUM LB/EA APPROX REF STEEL LB/EA APPROX REF TI 02 .648 - .485- .502 .090 .562 .018 .051 .029 03 .711 - .547- .565 .100 .625 .039 .104 .060 04 .773 .375 .735- .753 .1

9、10 - .083 .233 .134 05 .773 .375 .735- .753 .120 .750 .099 .278 .160 06 .836 .375 .860- .878 .120 - .116 .326 .188 08 1.023 .469 1.047-1.065 .150 - .197 .554 .319 10 1.180 .625 1.047-1.065 .170 1.125 .206 .579 .334 12 1.367 .688 1.297-1.317 .185 1.375 .360 1.012 .583 14 1.507 .706 1.547-1.567 .200 -

10、 - - - 16 1.555 .719 1.605-1.630 .205 1.625 .455 1.340 .773 20 1.742 .781 1.855-1.880 .240 1.938 .672 1.950 1.125 AEROSPACE STANDARD AS1001 SHEET 3 OF 6 REV. J FITTING, TEE, STANDARD AND REDUCER, BULKHEAD ON RUN, INTERNAL PORT ON SIDE, FLARELESS TABLE 2 - LEG LENGTH B /17/ FORGING TUBE SIZE OF PORT

11、#1 SIZE /13/ 02 03 04 05 06 08 10 12 14 16 20 02 1.398 - - - - - - - - - - 03 1.430 1.477 - - - - - - - - - 04 1.585 1.632 1.695 - - - - - - - - 05 1.585 1.632 1.695 1.695 - - - - - - - 06 1.758 1.805 1.868 1.868 1.914 - - - - - - 08 1.727 1.774 1.837 1.837 1.883 2.055 - - - - - 10 1.804 1.851 1.914

12、 1.914 1.960 2.132 2.273 - - - - 12 1.883 1.930 1.993 1.993 2.039 2.211 2.352 2.461 - - - 14 2.040 2.087 2.150 2.150 2.196 2.368 2.509 2.618 2.618 - - 16 2.102 2.149 2.212 2.212 2.258 2.430 2.571 2.680 2.680 2.680 - 20 2.242 2.289 2.352 2.352 2.398 2.570 2.711 2.820 2.820 2.820 2.820 TABLE 3 - LEG L

13、ENGTH D /17/ FORGING TUBE SIZE OF PORT#2 SIZE /13/ 02 03 04 05 06 08 10 12 14 16 20 02 .867 - - - - - - - - - - 03 .883 .930 - - - - - - - - - 04 1.039 1.086 1.117 - - - - - - - - 05 1.039 1.086 1.117 1.117 - - - - - - - 06 1.086 1.133 1.164 1.164 1.180 - - - - - - 08 1.180 1.227 1.258 1.258 1.274 1

14、.367 - - - - - 10 1.273 1.320 1.351 1.351 1.367 1.460 1.523 - - - - 12 1.351 1.398 1.429 1.429 1.445 1.538 1.601 1.644 - - - 14 1.492 1.593 1.870 1.570 1.586 1.679 1.724 1.867 1.867 - - 16 1.554 1.601 1.632 1.632 1.648 1.741 1.804 1.867 1.867 1.867 - 20 1.695 1.742 1.773 1.773 1.789 1.882 1.945 2.00

15、8 2.008 2.008 2.008 TABLE 4 - MACHINED G /15/ /17/ FORGING TUBE SIZE FOR PORT #3 SIZE /13/ 02 03 04 05 06 08 10 12 14 16 02 - - - - - - - - - - 03 - - - - - - - - - - 04 .594 .656 - - - - - - - - 05 .594 .656 - - - - - - - - 06 .594 .656 .719 .781 - - - - - - 08 .594 .656 .719 .781 .844 - - - - - 10

16、 .594 .656 .719 .781 .844 - - - - - 12 .594 .656 .719 .781 .844 1.062 - - - - 14 .594 .656 .719 .781 .844 1.062 1.188 1.438 - - 16 .594 .656 .719 .781 .844 1.062 1.188 1.438 1.562 - 20 .594 .656 .719 .781 .844 1.062 1.188 1.438 1.562 1.688 AEROSPACE STANDARD AS1001 SHEET 4 OF 6 REV. J FITTING, TEE,

17、STANDARD AND REDUCER, BULKHEAD ON RUN, INTERNAL PORT ON SIDE, FLARELESS TABLE 5 - TUBE SIZE AND CORRESPONDING THREAD PORT SIZE (NOMINAL TUBE SIZE) T THREAD PER AS8879 CLASS 3A AND CLASS 3B 02 .125 .3125-24 UNJF 03 .188 .3750-24 UNJF 04 .250 .4375-20 UNJF 05 .312 .5000-20 UNJF 06 .375 .5625-18 UNJF 0

18、8 .500 .7500-16 UNJF 10 .625 .8750-14 UNJF 12 .750 1.0625-12 UNJ 14 .875 1.1875-12 UNJ 16 1.000 1.3125-12 UNJ 20 1.250 1.6250-12 UNJ NOTES NOTICE THIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE. /1/ M

19、ATERIAL: a. CODE LETTER DASH (-) - TYPE 4130 LOW ALLOY STEEL FORGING OR BAR PER AMS6370 OR AMS-S-6758, EXCEPT HEAT TREATMENT PER PROCUREMENT SPECIFICATION. /2/ b. CODE LETTER D - TYPE 2024-T6 OR -T851 ALUMINUM ALLOY BAR PER AMS-QQ-A-225/6 OR TYPE 2014-T6 ALUMINUM ALLOY FORGING PER AMS4133. /2/ c. CO

20、DE LETTER F - TYPE 4130 LOW ALLOY STEEL FORGING OR BAR PER AMS6370 OR AMS-S-6758, EXCEPT HEAT TREATMENT PER PROCUREMENT SPECIFICATION. /2/ d. CODE LETTER J - TYPE 304 CORROSION RESISTANT STEEL FORGING OR BAR PER AMS5639 OR AMS-QQ-S-763, EXCEPT HARDNESS PER PROCUREMENT SPECIFICATION. /2/ e. CODE LETT

21、ER K - TYPE 316 CORROSION RESISTANT STEEL FORGING OR BAR PER AMS5648 OR AMS-QQ-S-763, EXCEPT HARDNESS PER PROCUREMENT SPECIFICATION. /2/ f. CODE LETTER R - TYPE 321 CORROSION RESISTANT STEEL FORGING OR BAR PER AMS5645 OR AMS-QQ-S-763, EXCEPT HARDNESS PER PROCUREMENT SPECIFICATION. /2/ g. CODE LETTER

22、 S - TYPE 347 CORROSION RESISTANT STEEL FORGING OR BAR PER AMS5646 OR AMS-QQ-S-763, EXCEPT HARDNESS PER PROCUREMENT SPECIFICATION. /2/ h. CODE LETTER T - TYPE 6AL-4V TITANIUM ALLOY FORGING OR BAR PER AMS4928. i. CODE LETTER W - TYPE 7075-T73 ALUMINUM ALLOY FORGING PER AMS4141 OR AMS-QQ-A-367; OR 707

23、5-T7351 ALUMINUM ALLOY BAR PER AMS4124; OR 7075-T73 ALUMINUM ALLOY BAR PER AMS-QQ-A-225/9. /2/ /2/ HEAT TREATMENT: a. MATERIAL CODE LETTER (-) AND F - HARDNESS SHALL BE 92 HRB TO 40 HRC PER SPECIFICATION. b. MATERIAL CODE LETTERS D AND W - ELECTRICAL CONDUCTIVITY AND HARDNESS PER PROCUREMENT SPECIFI

24、CATION. c. MATERIAL CODE LETTERS J, K, R, AND S - HARDNESS SHALL BE 80 HRB MINIMUM PER PROCUREMENT SPECIFICATION. d. OTHER MATERIAL CODES - NONE. AEROSPACE STANDARD AS1001 SHEET 5 OF 6 REV. J FITTING, TEE, STANDARD AND REDUCER, BULKHEAD ON RUN, INTERNAL PORT ON SIDE, FLARELESS 3. FINISH: a. MATERIAL

25、 CODE LETTER (-) AND F - CADMIUM PLATE PER AMS-QQ-P-416, TYPE II, CLASS 2. b. MATERIAL CODE LETTER D - ANODIZE PER AMS2472 OR MIL-A-8625, TYPE II, CLASS 2, DYE GREEN SIMILAR TO COLOR 14187 OF FED-STD-595. c. MATERIAL CODE LETTERS J, K, R, AND S - PASSIVATE PER AMS2700 TYPE 6 OR 7. d. MATERIAL CODE L

26、ETTER T - FLUORIDE PHOSPHATE CONVERSION COAT PER AMS2486 OR ANODIZE PER AMS2488, TYPE 2. e. MATERIAL CODE LETTER W: (1) W CODE PARTS TO BE ANODIZED ONLY WILL HAVE NO FINISH CODE LETTER AFTER THE SIZE CODE IN THE PART NUMBER. THE FINISH WILL BE ANODIZE PER AMS2472 OR PER MIL-A-8625, TYPE II, CLASS 2

27、DYED BROWN SIMILAR TO COLOR 10080 OF AMS-STD-595. (2) W CODE PARTS TO BE COATED WITH HIGH PURITY ALUMINUM ONLY WILL HAVE THE FINISH CODE LETTER “V” AFTER THE SIZE CODE IN THE PART NUMBER. SEE PROCUREMENT SPECIFICATION FOR REQUIREMENTS. /4/ PROCUREMENT SPECIFICATION: AS18280 EXCEPT AS SPECIFIED ON TH

28、IS STANDARD. PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER AS LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST (QPL) PRI-QPL-AS18280 FOR THIS STANDARD. SEE www.eAuditN FOR CURRENT QPL ONLINE. /5/ IDENTIFICATION AT LOCATION SHOWN: M

29、ARK PER AS478 CLASS C OR D OR METHOD 7A3, 15A3, OR 15B. a. FOR SIZE 06 AND SMALLER MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, LETTERS “AS” AND MATERIAL CODE LETTER. b. FOR SIZE 08 AND LARGER, MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, BASIC PART NUMBER, AND MATERIAL CODE LETTER. 6. INVENTORIED PAR

30、TS CONFORMING TO THE PREVIOUS ISSUE MAY BE USED TO DEPLETION. /7/ FITTINGS WITH AS4377 STYLE G ENDS MAY BE DESIGNATED WITH THE SUFFIX “G“ AFTER THE PART NUMBER AND CANNOT BE USED IN PORTS. FITTINGS WITH AS4377 STYLE S ENDS MAY BE ASSEMBLED INTO INTERNALLY THREADED PORTS, BUT ARE NOT RECOMMENDED FOR

31、THIS APPLICATION. FITTINGS WITH AS4377 STYLE S ENDS ARE HISTORICALLY UNRELIABLE WHEN INSTALLED IN PORTS, BUT HAVE BEEN USED SUCCESSFULLY IN APPLICATIONS WITH PRESSURES LIMITED TO 1500 PSI. 8. INTENDED USE: THIS PART IS DESIGNED FOR USE IN TUBING CONNECTION SYSTEMS WITH NOMINAL OPERATING PRESSURES AS

32、 FOLLOWS: a. SIZES 02 THROUGH 16 IN LOW ALLOY STEEL, CORROSION RESISTANT STEEL AND TITANIUM ALLOY AT 3000 psi. b. SIZES 02 THROUGH 10 IN ALUMINUM ALLOY AND SIZE 20 IN ALL MATERIALS AT 1500 psi. c. SIZES 12 THROUGH 16 IN ALUMINUM ALLOY AT 900 psi. . d. SIZE 20 IN ALUMINUM ALLOY AT 600 psi. 9. FOR RED

33、UCER CONFIGURATIONS, THE PRESSURE RATING IS DETERMINED BY THE LARGEST PORT. 10. THE NON-REDUCER CONFIGURATION WITHOUT A SUFFIX PART NUMBER CODE IS THE FUNCTIONAL EQUIVALENT OF AS21910 FOR THE CORRESPONDING FORGING SIZE AND IS INTENDED TO BE SUITABLE AS A REPLACEMENT STANDARD. 11. WHEN MACHINING FROM

34、 BAR STOCK OR OVERSIZED FORGING, THE CENTER BODY DIMENSIONS SHALL CONFORM TO AS1376, TABLE 2. /12/ DIMENSIONS “E” AND “F” ARE DETERMINED BY THE FORGING SIZE. /13/ THE DIMENSIONS IN THE TABLE ARE FOR FINAL MACHINED PARTS. THE FORGING SIZE IS DETERMINED AS THE SIZE NECESSARY TO MAKE THE LARGEST FITTIN

35、G END. /14/ THE .125 MINIMUM DIMENSION APPLIES ONLY WHEN “Z” IS SPECIFIED. WHEN “Z” IS NOT SPECIFIED, USE “V” DIMENSION. /15/ WHEN “G” DIMENSION FROM TABLE 4 IS NOT SPECIFIED, USE “V” DIMENSION. /16/ WEIGHTS ARE FOR NON-REDUCERS ONLY. REDUCER FITTINGS WILL HAVE LOWER WEIGHTS. AEROSPACE STANDARD AS10

36、01 SHEET 6 OF 6 REV. J FITTING, TEE, STANDARD AND REDUCER, BULKHEAD ON RUN, INTERNAL PORT ON SIDE, FLARELESS /17/ REDUCER FITTINGS WHICH FALL IN THE SHADED AREA OF TABLES 2, 3, AND 4 SHOULD BE AVOIDED. IF THEY MUST BE USED, SPECIAL ATTENTION SHOULD BE GIVEN TO CLAMPING OR OTHER MEANS TO PROTECT THE

37、SMALLER PORT OR TUBE. /18/ FINISH CODE LETTER “V” SHALL BE PLACED AFTER SIZE CODES ONLY FOR MATERIAL CODE “W” PARTS THAT ARE TO BE COATED WITH HIGH PURITY ALUMINUM TO PROVIDE LOW ELECTRICAL CONTACT RESISTANCE. NO OTHER LETTERS ARE TO FOLLOW THE SIZE CODES. 19. REVISION INDICATOR: A CHANGE BAR (I) LO

38、CATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL RE

39、VISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. 20. INTERPRETATION OF DRAWING PER AS4296 21. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M; REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 MICRO

40、INCHES Ra. FORGED SURFACES MAY BE 250 MICROINCHES Ra. 22. BREAK ALL SHARP EDGES .003 TO .015, UNLESS OTHERWISE SPECIFIED. 23. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994. 24. DIMENSIONS ARE IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .016, ANGULAR DIMENSIONS 0 30. /25/ EX

41、AMPLES OF PART NUMBERS: PART NUMBER AS1001GJ101010 DESIGNATES A 304 CRES FITTING WITH SIZE 10 PORTS AND A STYLE G BULKHEAD END. PART NUMBER AS1001J101010 DESIGNATES A 304 CRES FITTING WITH SIZE 10 PORTS AND A STYLE S BULKHEAD END. PART NUMBER AS1001G-101010 DESIGNATES A 4130 LOW ALLOY STEEL FITTING

42、WITH SIZE 10 PORTS AND A STYLE G BULKHEAD END. PART NUMBER AS1001-101010 DESIGNATES A 4130 LOW ALLOY STEEL FITTING WITH SIZE 10 PORTS AND A STYLE S BULKHEAD END. PART NUMBER AS1001GW101010V DESIGNATES A 7075-T73 ALUMINUM ALLOY FITTING COATED WITH HIGH PURITY ALUMINUM WITH SIZE 10 PORTS AND A STYLE G BULKHEAD END. 26. AS6041 IS PREFERRED FOR USE IN LIEU OF THIS STANDARD. AS6041 OFFERS IMPROVED LENGTH TOLERANCES AND IMPROVED FINISH OF THE CONICAL SEAL AREA.