SAE AMS 3323A-2014 Sponge Fluorosilicone (FVM) Rubber Closed Cell《闭孔海绵氟硅酮橡胶》.pdf

《SAE AMS 3323A-2014 Sponge Fluorosilicone (FVM) Rubber Closed Cell《闭孔海绵氟硅酮橡胶》.pdf》由会员分享，可在线阅读，更多相关《SAE AMS 3323A-2014 Sponge Fluorosilicone (FVM) Rubber Closed Cell《闭孔海绵氟硅酮橡胶》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、_SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising theref

2、rom, is the sole responsibility of the user.”SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions.Copyright 2014 SAE InternationalAll rights reserved. No part of this publi

3、cation may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada)Tel: +1 724-776-4970 (out

4、side USA)Fax: 724-776-0790Email: CustomerServicesae.orgSAE WEB ADDRESS: http:/www.sae.orgSAE values your input. To provide feedbackon this Technical Report, please visithttp:/www.sae.org/technical/standards/AMS3323AAEROSPACE MATERIAL SPECIFICATIONAMS3323 REV. AIssued 1990-01Reaffirmed 2007-06Revised

5、 2014-05Superseding AMS3323Sponge, Fluorosilicone (FVM) RubberClosed CellRATIONALEThis specification is being revised to clarify that compression-deflection testing will be performed at room temperature and -85 F.1. SCOPE1.1 FormThis specification covers a fluorosilicone (FVM) rubber sponge in the f

6、orm of sheet, strip, extrusions, and molded shapes.1.2 ApplicationPrimarily for applications requiring closed-cell sponge rubber, resistant to fuel, and which will be flexible from -85 to +401 F (-65 to +205 C). Material covered by this specification is not intended to be resistant to aircraft turbi

7、ne engine oils.1.3 ClassificationSponge shall be classified by degree of firmness as follows:Class 1 - SoftClass 2 - Moderate FirmClass 3 - Firm1.3.1 Unless a specific class is ordered, Class 2 shall be supplied.1.4 Safety - Hazardous MaterialsWhile the materials, methods, applications, and processe

8、s described or referenced in this specification may involve the use of hazardous materials, this specification does not address the hazards which may be involved in such use. It is the sole responsibility of the user to ensure familiarity with the safe and proper use of any hazardous materials and t

9、o take necessary precautionary measures to ensure the health and safety of all personnel involved.SAE INTERNATIONAL AMS3323A Page 2 of 62. APPLICABLE DOCUMENTSThe issue of the following documents in effect on the date of the purchase order forms a part of this specification to the extent specified h

10、erein. The supplier may work to a subsequent revision of a document unless a specific document issue is specified. When the referenced document has been cancelled and no superseding document has been specified, the last published issue of that document shall apply.2.1 SAE PublicationsAvailable from

11、SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323, (inside USAand Canada) or 724-776-4970 (outside), www.sae.org.AMS2810 Identification and Packaging, Elastomeric Products2.2 ASTM PublicationsAvailable from ASTM International, 100 Barr Harbor Drive, P.O. Box C70

12、0, West Conshohocken, PA 19428-2959, Tel: 610-832-9585, www.astm.org.ASTM D 471 Rubber Property - Effect of LiquidsASTM D 1056 Flexible Cellular Materials - Sponge or Expanded Rubber3. TECHNICAL REQUIREMENTS3.1 MaterialShall be a compound, based on a fluorosilicone (FVM) rubber, suitably cured to pr

13、oduce a product meeting the requirements of this specification.3.2 FinishThe top and bottom surfaces of sheet and strip and the exterior surfaces of molded parts and extrusions (except ends) shall have a natural finish.3.3 PropertiesThe product shall conform to the following requirements; tests shal

14、l be performed on the product supplied and in accordance with ASTM D 1056, insofar as practicable:3.3.1 Compression-Deflection3.3.1.1 At Room TemperatureClass 1 2 to 9 psi ( 14 to 62 kPa)Class 2 9 to 18 psi ( 62 to 124 kPa)Class 3 18 to 27 psi (124 to 186 kPa)3.3.1.2 At -85 F 5 (-65 C 3) after 5 hou

15、rs 0.2 at -85 F 5 (-65 C 3)Class 160 psi (414 kPa), maximumClass 260 psi (414 kPa), maximumClass 3reportSAE INTERNATIONAL AMS3323A Page 3 of 63.3.2 Density, maximumClass 1 0.025 pound/cubic inch (692 kg/m3)Class 2 0.030 pound/cubic inch (830 kg/m3)Class 3 0.035 pound/cubic inch (969 kg/m3)3.3.3 Flui

16、d Resistance(Immediate Deteriorated Properties)Medium: ASTM Ref. Fuel B (ASTM D 471)Temperature: 68 to 86 F (20 to 30 C)3.3.3.1 Weight Change, maximum0 to 50% Time: 72 hours 23.3.4 Compression SetTemperature: 212 F 2 (100 C 1)3.3.4.1 Percent of Original Deflection, maximum 25% Time: 22 hours 0.23.3.

17、5 WeatheringWhen specified, the product shall have weather resistance acceptable to purchaser, determined by a procedure acceptable to purchaser and vendor.3.3.6 CorrosionThe product shall not have a corrosive effect on other materials when exposed to conditions normally encountered in service, dete

18、rmined by a procedure agreed upon by purchaser and vendor. Discoloration of metal shall not be considered objectionable.3.4 QualityThe product, as received by purchaser, shall be uniform in quality and condition, smooth, as free from foreign materials as commercially practicable, and free from imper

19、fections detrimental to usage of the product.3.5 TolerancesShall be as follows; measurements shall be made in accordance with ASTM D 1056.SAE INTERNATIONAL AMS3323A Page 4 of 63.5.1 Sheet and Strip3.5.1.1 ThicknessTABLE 1ANominal ThicknessInchTolerance, InchplusTolerance, Inchminus0.063 0.016 0.016O

20、ver 0.063 to 0.188, incl 0.031 0.031Over 0.188 to 0.312, incl 0.047 0.031Over 0.312 to 0.500, incl 0.047 0.047TABLE 1B SI UNITSNominal ThicknessMillimetresTolerance, MillimetresplusTolerance, Millimetresminus1.60 0.41 0.41Over 1.60 to 4.78, incl 0.79 0.79Over 4.78 to 7.92, incl 1.19 0.79Over 7.92 to

21、 12.70, incl 1.19 1.193.5.1.2 Length and WidthTABLE 2ANominal Length and WidthInchesTolerance, Inchplus and minusUp to 6, incl 0.125Over 6 to 18, incl 0.250Over 18 0.375TABLE 2B SI UNITSNominal Length and WidthMillimetresTolerance, Millimetresplus and minusUp to 152, incl 3.18Over 152 to 457, incl 6

22、.35Over 457 9.524. QUALITY ASSURANCE PROVISIONS4.1 Responsibility for InspectionThe vendor of sponge shall supply all samples for vendors tests and shall be responsible for performing all required tests. Results of such tests shall be reported to the purchaser as required by 4.5. Purchaser reserves

23、the right to sample and to perform any confirmatory testing deemed necessary to ensure that the sponge conforms to the requirements of this specification.4.2 Classification of Tests4.2.1 Acceptance TestsTests for the following requirements are acceptance tests and shall be performed on each lot:Requ

24、irement Paragraph ReferenceCompression-Deflection at room temperature 3.3.1.1Density 3.3.2SAE INTERNATIONAL AMS3323A Page 5 of 64.2.2 Preproduction TestsTests for all technical requirements of this specification are preproduction tests and shall be performed prior to or on the initial shipment of sp

25、onge to a purchaser, when a change in ingredients and/or processing requires reapproval as in 4.4.2, and when purchaser deems confirmatory testing to be required.4.3 Sampling and TestingShall be as follows:4.3.1 For AcceptanceTestsSufficient sponge shall be taken at random from each lot to perform a

26、ll required tests. The number of determinations for each requirement shall be as specified in the applicable test procedure or, if not specified therein, not less than three.4.3.1.1 A lot shall be all sponge produced from the same batch of compound processed in one continuous production run and pres

27、ented for vendors inspection at one time. An inspection lot shall not exceed 500 pounds (227 kg) and may be packaged in smaller quantities and delivered under the basic lot approval provided lot identification is maintained.4.3.1.2 A batch shall be the quantity of compound run through a mill or mixe

28、r at one time. Blending of previously compounded material is prohibited.4.3.1.3 When a statistical sampling plan has been agreed upon by purchaser and vendor, sampling shall be in accordance with such plan in lieu of sampling as in 4.2.1 and the report of 4.5 shall state that such plan was used.4.3.

29、2 For Preproduction TestsAs agreed upon by purchaser and vendor.4.4 Approval4.4.1 Sample sponge shall be approved by purchaser before sponge for production use is supplied, unless such approval be waived by purchaser. Results of tests on production sponge shall be essentially equivalent to those on

30、the approved sample.4.4.2 Vendor shall use ingredients, manufacturing procedures, processes, and methods of inspection on production sponge which are essentially the same as those used on the approved sample sponge. If necessary to make any change in ingredients, in type of equipment for processing,

31、 or in manufacturing procedures, vendor shall submit for reapproval a statement of the proposed changes in ingredients and/or processing and, when requested, sample sponge. Production sponge made by the revised procedure shall not be shipped prior to receipt of reapproval.4.5 ReportsThe vendor of sp

32、onge shall furnish with each shipment a report showing the results of tests to determine conformance to the technical requirements of this specification. This report shall include the purchase order number, vendors compound number, lot number, AMS3323A, class number, form and size or part number, an

33、d quantity.4.6 Resampling and RetestingIf any individual test specimen used in the above tests fails to meet the specified requirements, disposition of the sponge may be based on the results of testing three additional specimens for each original nonconforming specimen. Failure of any retest specime

34、n to meet the specified requirements shall be cause for rejection of the sponge represented and no additional testing shall be permitted. Results of all tests shall be reported.SAE INTERNATIONAL AMS3323A Page 6 of 65. PREPARATION FOR DELIVERY5.1 Identification and PackagingShall be in accordance wit

35、h AMS2810.6. ACKNOWLEDGMENTA vendor shall mention this specification number in all quotations and when acknowledging purchase orders.7. REJECTIONSSponge not conforming to this specification, or to modifications authorized by purchaser, will be subject to rejection.8. NOTES8.1 Dimensions and properti

36、es in inch/pound units and the Fahrenheit temperatures are primary; dimensions and properties in SI units and the Celsius temperatures are shown as the approximate equivalents of the primary units and are presented only for information.8.2 Sponge meeting the requirements of this specification has been classified under Federal Supply Classification (FSC) 9320.PREPARED BY AMS COMMITTEE “CE“