SAE AMS 3222H-2008 Synthetic Rubber Hot Oil Resistant High Swell 45 - 55《高膨胀为45-55的合成橡胶热油抵抗力》.pdf

《SAE AMS 3222H-2008 Synthetic Rubber Hot Oil Resistant High Swell 45 - 55《高膨胀为45-55的合成橡胶热油抵抗力》.pdf》由会员分享，可在线阅读，更多相关《SAE AMS 3222H-2008 Synthetic Rubber Hot Oil Resistant High Swell 45 - 55《高膨胀为45-55的合成橡胶热油抵抗力》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefr

2、om, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. Copyright 2008 SAE International All rights reserved. No part of this publication may

3、 be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) F

4、ax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.orgAMS3222H AEROSPACEMATERIALSPECIFICATIONIssued 1945-07 Reaffirmed 1998-08 Revised 2008-06 Superseding AMS3222G Synthetic Rubber Hot Oil Resistant, High Swell 45 - 55RATIONALEAMS3222H is a Five Year Review and update of t

5、his specification. 1. SCOPE 1.1 Form This specification covers a synthetic rubber in the form of sheet, strip, tubing, extrusions, and molded shapes. 1.2 Application This product has been typically used for gasket-type seals in contact with hot, petroleum-based lubricating oils where a space-filling

6、 seal operating from -40 to +212 F (-40 to +100 C) is required, but usage is not limited to such applications. 1.3 Safety Hazardous Materials While the materials, methods, applications, and processes described or referenced in this specification may involve the use of hazardous materials, this speci

7、fication does not address the hazards which may be involved in such use. It is the sole responsibility of the user to ensure familiarity with the safe and proper use of any hazardous materials and to take necessary precautionary measures to ensure the health and safety of all personnel involved. 2.

8、APPLICABLE DOCUMENTS The issue of the following documents in effect on the date of the purchase order forms a part of this specification to the extent specified herein. The supplier may work to a subsequent revision of a document unless a specific document issue is specified. When the referenced doc

9、ument has been cancelled and no superseding document has been specified, the last published issue of that document shall apply. 2.1 SAE Publications Available from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or 724-776-4970 (outside

10、 USA), www.sae.org. AMS2279 Tolerances, Rubber Products AMS2810 Identification and Packaging, Elastomeric Products SAE AMS3222H - 2 -2.2 ASTM Publications Available from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, Tel: 610-832-9585, www.astm.org. ASTM

11、D 395 Rubber Property Compression Set ASTM D 412 Rubber Properties in Tension ASTM D 471 Rubber Property Effect of Liquids ASTM D 573 Rubber Deterioration in an Air Oven ASTM D 2137 Rubber Property Brittleness Point of Flexible Polymers and Coated Fabrics ASTM D 2240 Rubber Property Durometer Hardne

12、ss 3. TECHNICAL REQUIREMENTS 3.1 Material Shall be a compound, based on a synthetic elastomer, suitably cured to produce a product meeting the requirements of 3.2.3.1.1 Color Shall be black. 3.2 Properties The product shall conform to the following requirements as shown in Table 1; tests shall be pe

13、rformed on the product supplied and in accordance with specified ASTM methods, insofar as practicable: TABLE 1 PROPERTIES Paragraph Property Requirement Test Methods 3.2.1 As Received 3.2.1.1 Hardness, Durometer “A” or equivalent 50 5 ASTM D 2240 3.2.1.2 Tensile Strength, minimum1.5 ksi (10.3 MPa) A

14、STM D 412, Die B or C 3.2.1.3 Elongation, minimum 400% ASTM D 412, Die B or C 3.2.2 Petroleum Lubricating Oil Resistance (Immediate Deteriorated Properties) ASTM D 471 Medium: ASTM Oil No. 1 Temperature: 302 F 5 (150 C 3) 3.2.2.1 Hardness Change, Durometer “A” or equivalent -5 to +5 Time: 24 hours 0

15、.2 3.2.2.2 Tensile Strength Change, maximum -50% 3.2.2.3 Elongation Change, maximum -50% 3.2.2.4 Volume Change +15 to +30% 3.2.2.5 Decomposition None 3.2.2.6 Surface Tackiness None 3.2.3 Petroleum Lubricating Oil Resistance (Immediate Deteriorated Properties) ASTM D 471 Medium: ASTM Oil No. 1 Temper

16、ature: 302 F 5 (150 C 3) Time: 70 hours 0.5 3.2.3.1 Hardness Change, Durometer “A” or equivalent -10 to +10 3.2.3.2 Volume Change +15 to +40% 3.2.3.3 Decomposition None 3.2.3.4 Surface Tackiness None SAE AMS3222H - 3 -TABLE 1 PROPERTIES (CONT.) Paragraph Property Requirement Test Methods 3.2.3.5 Ben

17、d (flat) No crackingor checking 3.2.4 Dry Heat Resistance ASTM D 573 Temperature: 212 F 2 (100 C 1) 3.2.4.1 Hardness Change, Durometer “A” or equivalent 0 to +10 Time: 70 hours 0.5 3.2.4.2 Tensile Strength Change, maximum -40% 3.2.4.3 Elongation Change, maximum -50% 3.2.5 Compression set ASTM D 395,

18、 Method B Temperature: 212 F 2 3.2.5.1 Percent of Original Deflection, maximum 85(100 C 1) Time: 70 hours 0.5 3.2.6 Low-Temperature Resistance ASTM D 2137, Method A Temperature: -40 F 2 3.2.6.1 Brittleness Pass (-40 C 1) Time: 5 hours 0.2 3.3 Quality The product, as received by purchaser, shall be u

19、niform in quality and condition, as free from foreign materials as commercially practicable, and free from imperfections detrimental to usage of the product. 3.4 Dimensions and Tolerances Dimensions and tolerances shall be as specified in the parts standard, drawing or purchase document. If not spec

20、ified, shall conform to all applicable requirements of AMS2279. 3.5 Toxicological Formulations The material shall have no adverse effects on the health of personnel when used for its intended purpose in accordance with manufacturers instructions and with appropriate handling procedures. 4. QUALITY A

21、SSURANCE PROVISIONS 4.1 Responsibility for Inspection The vendor of the product shall supply all samples for vendors tests and shall be responsible for the performance of all required tests. Purchaser reserves the right to sample and to perform any confirmatory testing deemed necessary to ensure tha

22、t the product conforms to specified requirements. 4.2 Classification of Tests 4.2.1 Acceptance Tests Tests for the following requirements shown in Table 2 are acceptance tests and shall be performed on each lot: TABLE 2 Requirement Paragraph Reference Hardness, as received 3.2.1.1 Tensile Strength,

23、as received 3.2.1.2 Elongation, as received 3.2.1.3 Volume Change in Oil 3.2.2.4 and 3.2.3.2 SAE AMS3222H - 4 -4.2.1.1 Lot A quantity of one size of product processed and packaged as one production entity from a batch. 4.2.1.2 Batch The quantity of compound run through a mill or mixer at one time. 4

24、.2.1.3 Random Sampling The method shall be as specified in the parts standard, drawing or purchase document. If not specified, product shall be taken at random from each lot to perform all the required acceptance tests. The number of test iterations for each requirement shall be specified in the app

25、licable test procedure. 4.2.1.4 Sample shall be from a production batch/lot. 4.2.2 Preproduction Tests All technical requirements are preproduction tests and shall be performed prior to or on the initial shipment of a product to a purchaser, when a change in ingredients and/or processing requires re

26、approval as in 4.4.2, and when purchaser deems confirmatory testing to be required. 4.3 Sampling and Testing Shall be as follows: 4.3.1 For Acceptance Tests Sufficient product shall be taken at random from each lot to perform all required tests. The number of determinations for each requirement shal

27、l be as specified in the applicable test procedure or, if not specified therein, not less than three. 4.3.1.1 If specimens cannot be prepared from the product, ASTM test specimens prepared from the same batch and state of cure shall be used. When the product supplied is an extrusion of such shape th

28、at suitable test specimens cannot be cut from the product, a separate flat strip test sample from the same production lot shall be supplied upon request. This strip shall be prepared from tubing 1.000 inch 0.063 (25.40 mm 1.60) in OD by 0.075 inch 0.008 (1.90 mm 0.20) in wall thickness, mechanically

29、 slit and flattened into a strip while being extruded, and cured in the same manner as production product. When the product is a molded shape from which test specimens cannot be cut, a slab, 6 inches (152 mm) square by 0.075 inch 0.008 (1.90 mm 0.20) thick, molded from the same batch of compound sha

30、ll be supplied upon request. 4.3.1.2 When a statistical sampling plan has been agreed upon by purchaser and vendor, sampling shall be in accordance with such plan in lieu of sampling as in 4.3 and the report of 4.5 shall state that such plan was used.4.3.2 For Preproduction Tests As agreed upon by p

31、urchaser and vendor. 4.4 Approval 4.4.1 Sample product shall be approved by purchaser before product for production use is supplied, unless such approval is waived by the purchaser. Results of tests on production product shall be essentially equivalent to those on the approved sample. SAE AMS3222H -

32、 5 -4.4.2 Vendor shall use ingredients, manufacturing procedures, processes, and methods of inspection on production product which are essentially the same as those used on the approved sample product. If it is necessary to make any change in ingredients, in type of equipment for processing, or in m

33、anufacturing procedures, vendor shall submit for reapproval a statement of the proposed changes in ingredients and/or processing and, when requested, sample product. Production product made by the revised procedure shall not be shipped prior to receipt of reapproval. 4.5 Reports The supplier of the

34、product shall make readily available a report showing the results of tests to determine conformance to the acceptance requirements and stating that the product conforms to the other technical requirements. This report shall include AMS number with revision, manufacturers identification and product d

35、esignation, batch/lot number and date of manufacture.4.6 Resampling and Retesting If any specimen fails, a retesting of three additional specimens for each nonconforming specimen shall be necessary for product acceptance. Whenever possible the same batch/lot of product as was used for the failed tes

36、t shall be used for retesting. Failure of any retest specimen shall be cause for rejection. Results of all tests shall be reported. 5. PREPARATION FOR DELIVERY 5.1 Identification and Packaging Shall be as specified in the parts standard, drawing or purchase document. If not specified, shall be as fo

37、llows: Packaging shall be in accordance with AMS2810. A lot may be packaged in small quantities and delivered under the basic lot approval provided lot information is maintained. 5.1.1 Each package, box, and shipping container shall be permanently and legibly marked with the following when pertinent

38、:Specification number AMS number with revision, class, grade, and type Manufacturers identification Manufacturers product designation Batch/lot number Date of manufacturing/packaging Shelf life expiration date Storage conditions 6. ACKNOWLEDGMENT A vendor shall mention this specification number and

39、its revision letter in all quotations and when acknowledging purchase orders. 7. REJECTIONS Product not conforming to this specification, or to modifications authorized by purchaser, will be subject to rejection. 8. NOTES 8.1 A change bar (|) located in the left margin is for the convenience of the

40、user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of a specification. An (R) symbol to the left of the document title indicates a complete revision of the specification, including technical revision. Change bars and (R) are not used in orig

41、inal publications, nor in specifications that contain editorial changes only. 8.2 Terms used in AMS are clarified in ARP1917. SAE AMS3222H - 6 -8.3 Dimensions and properties in inch/pound units and the Fahrenheit temperatures are primary; dimensions and properties in SI units and the Celsius tempera

42、tures are shown as the approximate equivalents of the primary units and are presented only for information. 8.4 Purchase documents should specify not less than the following: AMS3222GForm and size or part number of product desired Quantity of product desired Method of test and acceptance standards for weathering (See 3.2.7) and corrosion (See 3.2.8). PREPARED BY AMS COMMITTEE “CE“