SAE AMS 3043D-2008 Magnetic Particles Nonfluorescent Wet Method Oil Vehicle Aerosol Packaged《气溶胶包覆的以油为媒介物的非荧光磁性粒子用湿法》.pdf

《SAE AMS 3043D-2008 Magnetic Particles Nonfluorescent Wet Method Oil Vehicle Aerosol Packaged《气溶胶包覆的以油为媒介物的非荧光磁性粒子用湿法》.pdf》由会员分享，可在线阅读，更多相关《SAE AMS 3043D-2008 Magnetic Particles Nonfluorescent Wet Method Oil Vehicle Aerosol Packaged《气溶胶包覆的以油为媒介物的非荧光磁性粒子用湿法》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、AEROSPACE MATERIAL SPECIFICATION AMS3043 REV. D Issued 1974-03 Revised 2008-11 Reaffirmed 2014-08 Superseding AMS3043C Magnetic Particles, Nonfluorescent Wet Method, Oil Vehicle, Aerosol Packaged RATIONALE AMS3043D has been reaffirmed to comply with the SAE five year review policy. _ SAE Technical S

2、tandards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole

3、 responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2014 SAE International All rights reserved. No part of this publication may be

4、 reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) F

5、ax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AMS3043D 1. SCOPE 1.1 Form This specification covers nonfluorescent magnetic particles in the form

6、 of a mixed, ready-to-use suspension in an odorless oil vehicle and packaged in aerosol cans. 1.2 Application These particles have been used typically as the inspection medium in a wet magnetic particle inspection system in accordance with ASTM E 1444, but usage is not limited to such application. 1

7、.3 Safety-Hazardous Materials While the materials, methods, applications, and processes described or referenced in this specification may involve the use of hazardous materials, this specification does not address the hazards which may be involved in such use. It is the sole responsibility of the us

8、er to ensure familiarity with the safe and proper use of any hazardous materials and to take necessary precautionary measures to ensure the health and safety of all personnel involved. 2. APPLICABLE DOCUMENTS The issue of the following documents in effect on the date of the purchase order forms a pa

9、rt of this specification to the extent specified herein. The supplier may work to a subsequent revision of a document unless a specific document issue is specified. When the referenced document has been cancelled and no superseding document has been specified, the last published issue of that docume

10、nt shall apply. SAE INTERNATIONAL AMS3043D Page 2 of 6 2.1 SAE Publications Available from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or 724-776-4970 (outside USA), www.sae.org. AMS2641 Vehicle, Magnetic Particle Inspection, Petrol

11、eum Base AMS2820 Packaging, Aerosol AMS3042 Magnetic Particles, Nonfluorescent, Wet Method, Dry Powder AS5282 Tool Steel Ring for Magnetic Particle Inspection 2.2 ASTM Publications Available from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, Tel: 610-832

12、-9585, www.astm.org. ASTM D 1966 Test Method for Foots in Linseed Oil ASTM E 1444 Magnetic Particle Examination 3. TECHNICAL REQUIREMENTS 3.1 Material The product shall be composed of durable nonfluorescent magnetic particles conforming to AMS3042 which may have been treated to attain the color spec

13、ified. The particles shall be mixed in the proper proportion with an inspection vehicle conforming to AMS2641 and packaged in aerosol cans in accordance with AMS2820. 3.2 Storage Life The product shall meet the requirements specified in 3.3 when tested at any time up to 12 months from date of manufa

14、cture. 3.3 Properties The product shall conform to the following requirements. Tests shall be performed on the product supplied and in accordance with specified test procedures, using a test suspension prepared by spraying the complete contents of several aerosol cans into a clean container to produ

15、ce at least 1 quart (1 L) of suspension, agitating the aerosol cans frequently to exhaust all particulate material. 3.3.1 Contamination The product shall show no evidence of foreign material, agglomeration, or scum, determined by visual examination of the test suspension at the following times: 3.3.

16、1.1 During preparation of the test suspension as in 3.3. 3.3.1.2 After mixing the test suspension, allowing it to stand for not less than 30 minutes, and agitating it slightly. 3.3.1.3 During tests to determine other characteristics of the product. 3.3.2 Concentration The concentration of magnetic p

17、articles in the freshly sprayed suspension shall be 1.0 to 2.4 mL of magnetic particles in 100-mL of suspension, determined by mixing the suspension thoroughly, filling a 100-mL calibrated centrifuge tube as specified in ASTM D 1966, demagnetizing, allowing to stand undisturbed for at least 30 minut

18、es, and reading, on the centrifuge tube, the volume of particles settled from the suspension. SAE INTERNATIONAL AMS3043D Page 3 of 6 3.3.3 Sensitivity The product shall provide indications of at least the first six holes of the ring test specimen of 4.4 when tested as follows: 3.3.3.1 Place the ring

19、 on a 1-inch (25-mm) diameter copper bar and circularly magnetize in a standard magnetic particle inspection unit by passing 2500 amperes of direct current through the bar immediately before spraying the ring with the contents of an agitated aerosol can from the same lot that has passed the concentr

20、ation and contamination tests. Examine the ring under a white light of not less than 100 foot-candles (1000 lx) at the examining surface. 3.3.4 Color The color of the magnetic particles in suspension shall be black, red, gray, or as otherwise specified, determined by observing a well-dispersed sampl

21、e of the test suspension in a glass container under a white light of not less than 100 foot-candles (1000 lx) at the examining surface. 3.4 Aerosol Spray Cans The magnetic particles shall be packaged in aerosol cans conforming to AMS2820 and meeting the requirements of 3.4.1 and 3.4.2. The aerosol c

22、ans selected for test shall be maintained at room temperature for not less than 12 hours prior to testing. During testing, the aerosol can may be immersed in water at 77 F 2 (25 C 1) periodically to maintain the container and its contents at room temperature. 3.4.1 Sprayability and Leakage 3.4.1.1 A

23、ll aerosol pressure cans shall be equipped with a spray nozzle. The nozzle shall provide a fine, steady spray and shall deposit the product evenly on a flat or vertical surface. No chunks of solids shall be expelled and no clogging of the nozzle shall occur. After clearing the nozzle in accordance w

24、ith manufacturers instructions, there shall be no perceptible leakage. 3.4.1.2 The characteristics of the spray pattern and the performance of the spray nozzle shall be evaluated by vigorously shaking the can for not less than 30 seconds with the contained pellet sounding on each shake and spraying

25、a pattern on large sheets of newspaper or similar surfaces to determine the coverage and evenness of the spray. After spraying several patterns, the nozzle shall be examined for evidence of chunks of solids and clogging. The nozzle shall be cleared by inverting the can and spraying until only gas es

26、capes. The can shall be immersed for not less than 15 minutes in water at 126 to 129 F (52 to 54 C); there shall be no visible evidence of leakage from, or distortion of, the pressurized container. The pressurized can shall be immersed in water at 77 F 2 (25 C 1) until the temperature has stabilized

27、 and, after vigorous shaking, two more patterns shall be sprayed. The spray characteristics shall not have changed and there shall be no chunking or clogging of the nozzle. 3.4.1.3 CAUTION DO NOT HEAT THE PRESSURIZED CAN OVER 129 F (54 C). 3.4.2 Complete Expulsion The complete usable portion of the

28、contents shall have been expelled before the propellant is expended. The expelled contents shall be not less than 5 fluid ounces (148 mL) and the particle content shall conform to the aerosol spray requirements. Vigorously shake for not less than 30 seconds each unused can to be tested, with the con

29、tained pellet sounding on each shake, and expel the contents in a series of short blasts into a clean graduated glass container in such a manner that the entire contents of the can will be retained in the glass container. The aerosol can may be immersed periodically in water at 77 F 2 (25 C 1) to ma

30、intain the can and its contents at room temperature. Repeat the vigorous shaking and short blasts until there is no further escape of gas. SAE INTERNATIONAL AMS3043D Page 4 of 6 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for Inspection The manufacturer of the product shall supply all samples

31、 for manufacturers tests and shall be responsible for the performance of all specified tests. Purchaser reserves the right to sample and to perform any confirmatory testing deemed necessary to ensure that the product conforms to specified requirements. 4.2 Classification of Tests 4.2.1 Acceptance Te

32、sts All technical requirements, except storage life (3.2), are acceptance tests and shall be performed on each lot. 4.2.2 Preproduction Tests All technical requirements are preproduction tests and shall be performed prior to or on the initial shipment of a product to a purchaser, when a change in in

33、gredients and/or processing requires reapproval as in 4.4.2, and when purchaser deems confirmatory testing to be required. 4.3 Sampling and Testing Shall be as follows: 4.3.1 For Acceptance Tests Sufficient product shall be taken at random from each lot to perform all required tests. The number of d

34、eterminations for each requirement shall be as specified in the applicable test procedure or, if not specified therein, not less than three. 4.3.1.1 A lot shall be all product produced in a single production run from the same batch of raw materials under the same fixed conditions and presented for i

35、nspection at one time. 4.3.2 For Preproduction Tests As agreed upon by purchaser and vendor. 4.4 Tool Steel Test Ring Shall be in accordance with AS5282. 4.5 Approval 4.5.1 Sample product shall be approved by purchaser before product for production use is supplied, unless such approval be waived by

36、purchaser. Results of tests on production product shall be equivalent to those on the approved sample. 4.5.2 Manufacturer shall use ingredients, manufacturing procedures, processes, and methods of inspection on production product that are the same as those used on the approved sample. If necessary t

37、o make any changes in ingredients, processing techniques, or manufacturing procedures, manufacturer shall submit for reapproval a statement of the proposed changes in ingredients and/or processing and, when requested, sample product. Production product shall not be shipped prior to receipt of reappr

38、oval. SAE INTERNATIONAL AMS3043D Page 5 of 6 4.6 Reports The vendor of the product shall furnish with each shipment a report stating that the product conforms to all technical requirements. This report shall include the purchase order number, lot number, AMS3043D, manufacturers material designation,

39、 lot number, date of manufacture, and quantity. 4.7 Resampling and Retesting If any sample used in the above tests fails to meet specified requirements, disposition of the product may be based on the results of testing three additional samples for each original nonconforming sample. Failure of any r

40、etest sample to meet specified requirements shall be cause for rejection of the product represented. Results of all tests shall be reported. 5. PREPARATION FOR DELIVERY 5.1 Packaging and Identification 5.1.1 The magnetic particles shall be packaged in aerosol cans conforming to AMS2820 and meeting t

41、he requirements of 3.4. Magnetic particles shall be completely mixed with vehicle and each can shall contain a pellet to aid in agitation or mixing of the material prior to spraying. The aerosol cans shall be of suitable size for hand application of the product or as otherwise specified by purchaser

42、. 5.1.2 A lot of particles in aerosol cans may be packaged in small quantities and delivered under the basic lot approval provided lot identification is maintained. 5.1.3 Each container shall be legibly identified on a durable label with not less than the following information: MAGNETIC PARTICLES, N

43、ONFLUORESCENT, WET METHOD, OIL VEHICLE, AEROSOL PACKAGED AMS3043D COLOR _ MANUFACTURERS IDENTIFICATION_ DATE OF MANUFACTURE _ * _ LOT NUMBER _ QUANTITY _ MANUFACTURERS INSTRUCTIONS FOR USE _ * _ APPROPRIATE WARNINGS OR PRECAUTIONARY NOTICES _ * May be included in the manufacturers identification or

44、lot number * May be on a separate sheet 5.1.4 Aerosol cans shall be packed in an exterior shipping container capable of protecting the product, during shipment and storage, against damage from exposure to moisture, weather, or any other normal hazard. 5.1.5 Containers of the product shall be prepare

45、d for shipment in accordance with commercial practice and in compliance with applicable rules and regulations pertaining to the handling, packaging, and transportation of the product to ensure carrier acceptance and safe delivery. 6. ACKNOWLEDGMENT A vendor shall mention this specification number an

46、d its revision letter in all quotations and when acknowledging purchase orders. SAE INTERNATIONAL AMS3043D Page 6 of 6 7. REJECTIONS Product not conforming to this specification, or to modifications authorized by purchaser, will be subject to rejection. 8. NOTES 8.1 A change bar ( l ) located in the

47、 left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of the document title indicates a complete revision of the document, including technical revisions. Change bars and (R) are not used in original publications, nor in documents that contain editorial changes only. 8.2 Terms used in AMS are clarified in ARP1917. 8.3 Dimensions in inch/pound units and the Fahrenheit temperatures are prima