REG UFGS-26 51 00 00 40-2013 INTERIOR LIGHTING.pdf

《REG UFGS-26 51 00 00 40-2013 INTERIOR LIGHTING.pdf》由会员分享，可在线阅读，更多相关《REG UFGS-26 51 00 00 40-2013 INTERIOR LIGHTING.pdf（34页珍藏版）》请在麦多课文档分享上搜索。

1、*USACE / NAVFAC / AFCESA / NASA UFGS-26 51 00.00 40 (February 2013)-Preparing Activity: NASA SupersedingUFGS-26 51 00.00 40 (February 2011)UNIFIED FACILITIES GUIDE SPECIFICATIONSReferences are in agreement with UMRL dated January 2013*SECTION TABLE OF CONTENTSDIVISION 26 - ELECTRICALSECTION 26 51 00

2、.00 40INTERIOR LIGHTING02/13PART 1 GENERAL1.1 REFERENCES1.2 DEFINITIONS1.3 ADMINISTRATIVE REQUIREMENTS1.3.1 Pre-Installation Meetings1.4 SUBMITTALS1.5 QUALITY ASSURANCE1.5.1 Lighting Fixtures, Complete with Lamps and Ballasts1.5.2 Regulatory Requirements1.5.3 Standard Products1.5.3.1 Alternative Qua

3、lifications1.5.3.2 Material and Equipment Manufacturing Date1.5.4 Sustainable Design Requirements1.5.4.1 Local/Regional Materials Documentation1.5.4.2 Environmental Data1.5.5 Energy Efficiency Data1.6 WARRANTY1.6.1 Electronic Ballast WarrantyPART 2 PRODUCTS2.1 DESIGN REQUIREMENTS2.2 COMPONENTS2.2.1

4、Fluorescent Lighting Fixtures2.2.1.1 Fluorescent Lamp Electronic Ballasts2.2.1.2 Fluorescent Lamp Electronic Dimming Ballast2.2.1.3 Fluorescent Electromagnetic Ballasts2.2.1.4 Fluorescent Lamps2.2.1.5 Compact Fluorescent Fixtures2.2.1.6 Open-Tube Fluorescent Fixtures2.2.1.7 Air Handling Fixtures2.2.

5、1.8 Electromagnetic Interference Filters2.2.2 High-Intensity-Discharge (Hid) Lighting Fixtures2.2.2.1 HID Ballasts2.2.2.2 High-Pressure Sodium (HPS) LampsSECTION 26 51 00.00 40 Page 1Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-2.2.2.3 Low-Pressur

6、e Sodium Lamps2.2.2.4 Metal-Halide Lamps2.2.3 Incandescent Lighting Fixtures2.2.3.1 Incandescent Lamps2.2.4 Commercial Incandescent Lighting Fixtures2.2.4.1 Surface-Mounted Fixtures2.2.4.2 Recessed Fixtures2.2.4.3 Pendant-Mounted Fixtures2.2.5 Industrial Incandescent Lighting Fixtures2.2.6 Enclosed

7、And Gasketed Vapor-Tight Fixtures2.2.7 Incandescent Lamps2.2.8 Recess- And Flush-Mounted Fixtures2.2.9 Suspended Fixtures2.2.10 Fixtures For Hazardous Locations2.3 EQUIPMENT2.3.1 Equipment Identification2.3.1.1 Manufacturers Nameplate2.3.1.2 Labels2.3.2 Power Hook Fixture Hangers2.3.3 Auxiliary Inst

8、ant-On System2.3.4 Support Hangers for Lighting Fixtures in Suspended Ceilings2.3.4.1 Wires2.3.4.2 Wires, for Humid Spaces2.3.4.3 Straps2.3.4.4 Rods2.3.5 Factory Applied Finish2.4 ACCESSORIES2.4.1 Lowering Devices For High-Bay Lighting Fixtures2.4.1.1 Contact Assembly2.4.1.2 Lockbox2.4.1.3 Cable/Cha

9、inPART 3 EXECUTION3.1 PREPARATION3.1.1 Field Applied Painting3.2 INSTALLATION3.2.1 Lamps3.2.2 Lighting Fixtures3.2.3 Suspended Fixtures3.2.4 Ballasts3.2.4.1 Remote Ballasts3.2.4.2 Electronic Dimming Ballasts3.3 FIELD QUALITY CONTROL3.3.1 Electronic Dimming Ballast3.4 FIELD TESTING3.5 MAINTENANCE3.5.

10、1 Operational Service- End of Section Table of Contents -SECTION 26 51 00.00 40 Page 2Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-*USACE / NAVFAC / AFCESA / NASA UFGS-26 51 00.00 40 (February 2013)-Preparing Activity: NASA SupersedingUFGS-26 51 0

11、0.00 40 (February 2011)UNIFIED FACILITIES GUIDE SPECIFICATIONSReferences are in agreement with UMRL dated January 2013*SECTION 26 51 00.00 40INTERIOR LIGHTING02/13*NOTE: This guide specification covers requirements for interior lighting installations. Requirements for materials and procedures for sp

12、ecial or unusual design should be added as necessary to fit specific projects.Emergency lighting and exit signs are covered in Section 26 52 00.00 40 EMERGENCY LIGHTING. Lighting control devices are covered in the Section 26 09 23.00 40 LIGHTING CONTROL DEVICES.Adhere to UFC 1-300-02 Unified Facilit

13、ies Guide Specifications (UFGS) Format Standard when editing this guide specification or preparing new project specification sections. Edit this guide specification for project specific requirements by adding, deleting, or revising text. For bracketed items, choose applicable items(s) or insert appr

14、opriate information.Remove information and requirements not required in respective project, whether or not brackets are present.Comments, suggestions and recommended changes for this guide specification are welcome and should be submitted as a Criteria Change Request (CCR).*NOTE: In compliance with

15、Executive Order 12902 and FAR section 23.704 which directs federal agencies to purchase products in the upper 25 percent of energy efficiency, the following products specified in this section meet or exceed the U.S. Department of Energy, Federal Energy Management Program (DOE/FEMP) Product Energy Ef

16、ficiency Recommendations (PEER) for the Recommended energy efficiency levels.This specification contains products recommended by FEMP. The following recommendations are currently SECTION 26 51 00.00 40 Page 3Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IH

17、S-,-,-on the FEMP site on the internet. Additional recommendations may be added or existing recommendations updated at any time.FEMP LT-1 (1998) How to Buy Energy EfficientFluorescent Tube LampsFEMP LT-2 (2000) How to Buy Energy-EfficientFluorescent BallastsTo view the latest on-line information abo

18、ut buying energy efficient products go to the FEMP home page at: http:/www1.eere.energy.gov/femp/technologies/procuring_eeproducts.html*NOTE: TO DOWNLOAD UFGS GRAPHICSGo to http:/www.wbdg.org/ccb/NAVGRAPH/graphtoc.pdf.*NOTE: This site contains lighting fixture sketches (Graphics) and are available i

19、n metric (SI) and U.S. Customary (IP) system dimensions. Sketch titles and style numbers are unchanged for both types. The metric values indicated are a conversion of the IP system dimensions.Do not include list of sketches, or sketches themselves, in project specifications. Use lighting fixture ske

20、tches as details on drawings whenever possible. If special features are required for a project, do not modify sketches, but indicate these changes on notes in fixture schedule. The “NL“ style numbers and dates should remain on the drawing details.*NOTE: Show the following information on project draw

21、ings:1. Type, style, mounting, and lamp arrangement2. Location of fixtures3. Wattage, voltage, and frequency rating required4. Type of reflector, diffuser required5. Glass/plastic lens6. Accessories required, such as photocell, time switches, sensors, and auxiliary lamps7. Mounting height above floo

22、r or grade to bottom of fixtureSECTION 26 51 00.00 40 Page 4Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-8. Where wire for humid areas, rods, or straps are used (if more than one type of hanger is used)9. Reflecting or nonreflecting surface finish

23、10. Shielding required11. Referenced sketch12. NEMA distribution type (when applicable)13. Occupancy sensor location, mounting, and sensor detection type*NOTE: Demolition work that involves disposal of fluorescent and HID lamps and ballasts requires the use of Section 02 84 16 HANDLING OF LIGHTING B

24、ALLASTS AND LAMPS CONTAINING PCBs AND MERCURY.*PART 1 GENERALLighting fixtures and accessories mounted on exterior surfaces of buildings are specified in this section.Materials not considered to be lighting equipment or lighting fixture accessories are specified in Section 26 20 00 INTERIOR DISTRIBU

25、TION SYSTEM.1.1 REFERENCES*NOTE: This paragraph is used to list the publications cited in the text of the guide specification. The publications are referred to in the text by basic designation only and listed in this paragraph by organization, designation, date, and title.Use the Reference Wizards C

26、heck Reference feature when you add a RID outside of the Sections Reference Article to automatically place the reference in the Reference Article. Also use the Reference Wizards Check Reference feature to update the issue dates.References not used in the text will automatically be deleted from this

27、section of the project specification when you choose to reconcile references in the publish print process.*The publications listed below form a part of this specification to the extent referenced. The publications are referred to in the text by the basic designation only.SECTION 26 51 00.00 40 Page

28、5Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ASTM INTERNATIONAL (ASTM)ASTM A1008/A1008M (2012) Standard Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy and High-Strength Low-Alloy with Improved Formability

29、, Solution Hardened, and Bake HardenedASTM A123/A123M (2012) Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel ProductsASTM A368 (1995; E 2009; R 2009) Standard Specification for Stainless Steel Wire StrandASTM A467/A467M (2007) Standard Specification for Machine Coil C

30、hainASTM A47/A47M (1999; R 2009) Standard Specification for Ferritic Malleable Iron CastingsASTM A580/A580M (2012a) Standard Specification for Stainless Steel WireASTM A641/A641M (2009a) Standard Specification for Zinc-Coated (Galvanized) Carbon Steel WireASTM A653/A653M (2011) Standard Specificatio

31、n for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip ProcessASTM B164 (2003; R 2008) Standard Specification for Nickel-Copper Alloy Rod, Bar, and WireASTM B26/B26M (2012) Standard Specification for Aluminum-Alloy Sand CastingsASTM B633 (2011) Standard S

32、pecification for Electrodeposited Coatings of Zinc on Iron and SteelASTM E2129 (2010) Standard Practice for Data Collection for Sustainability Assessment of Building ProductsCALIFORNIA ENERGY COMMISSION (CEC)CEC Title 24 (1978; R 2005) Californias Energy Efficiency Standards for Residential and Nonr

33、esidential BuildingsILLUMINATING ENGINEERING SOCIETY OF NORTH AMERICA (IES)IES HB-10 (2011) IES Lighting HandbookSECTION 26 51 00.00 40 Page 6Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-INSTITUTE OF ELECTRICAL AND ELECTRONICS ENGINEERS (IEEE)IEEE

34、 C2 (2012; Errata 2012; INT 1 2012; INT 2 2012; INT 3 2012) National Electrical Safety CodeIEEE C62.41.1 (2002; R 2008) Guide on the Surges Environment in Low-Voltage (1000 V and Less) AC Power CircuitsIEEE C62.41.2 (2002) Recommended Practice on Characterization of Surges in Low-Voltage (1000 V and

35、 Less) AC Power CircuitsIEEE Stds Dictionary (2009) IEEE Standards Dictionary: Glossary of Terms Errata 2 2012) National Electrical CodeNFPA 90A (2012) Standard for the Installation of Air Conditioning and Ventilating SystemsU.S. ENVIRONMENTAL PROTECTION AGENCY (EPA)Energy Star (1992; R 2006) Energy

36、 Star Energy Efficiency Labeling SystemUNDERWRITERS LABORATORIES (UL)UL 1029 (1994; Reprint Sep 2012) High-Intensity-Discharge Lamp BallastsUL 1598 (2008; Reprint Oct 2012) LuminairesUL 844 (2012) Standard for Luminaires for Use in Hazardous (Classified) LocationsUL 935 (2001; Reprint Nov 2011) Stan

37、dard for Fluorescent-Lamp Ballasts1.2 DEFINITIONSa. Unless otherwise specified or indicated, electrical and electronics terms used in these specifications, and on the drawings, are as defined in IEEE Stds Dictionary.b. Average life is the time after which 50 percent has failed and 50 percent has sur

38、vived under normal conditions.c. Total harmonic distortion (THD) is the root mean square (RMS) of all the harmonic components divided by the total fundamental current.1.3 ADMINISTRATIVE REQUIREMENTS1.3.1 Pre-Installation MeetingsWithin 30 _ days of Contract Award, the Contracting Officer may schedul

39、e a Pre-Installation meeting. Submit the following for review and approval:a. Local/Regional Materials Documentationb. Environmental Datac. Energy Efficiency DataSECTION 26 51 00.00 40 Page 8Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-d. Operatio

40、nal ServiceSubmit documentation that includes contact information, summary of procedures, and the limitations and conditions applicable to the project. Indicate manufacturers commitment to reclaim materials for recycling and/or reuse.1.4 SUBMITTALS*NOTE: Review Submittal Description (SD) definitions

41、 in Section 01 33 00 SUBMITTAL PROCEDURES and edit the following list to reflect only the submittals required for the project.The Guide Specification technical editors have designated those items that require Government approval, due to their complexity or criticality, with a “G.“ Generally, other s

42、ubmittal items can be reviewed by the Contractors Quality Control System. Only add a “G” to an item, if the submittal is sufficiently important or complex in context of the project.For submittals requiring Government approval on Army projects, a code of up to three characters within the submittal ta

43、gs may be used following the “G“ designation to indicate the approving authority. Codes for Army projects using the Resident Management System (RMS) are: “AE“ for Architect-Engineer; “DO“ for District Office (Engineering Division or other organization in the District Office); “AO“ for Area Office; “RO“ for Resident Office; and “PO“ for Project Office. Codes following the “G“ typically are not used for Navy, Air Force, and NASA projects.Choose the first bracketed item for Navy, Air Force and NASA projects, or choose the second bracketed item for Army projects.*