REG NASA-LLIS-0721--2000 Lessons Learned Design Considerations For Space Trusses.pdf

《REG NASA-LLIS-0721--2000 Lessons Learned Design Considerations For Space Trusses.pdf》由会员分享，可在线阅读，更多相关《REG NASA-LLIS-0721--2000 Lessons Learned Design Considerations For Space Trusses.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、Best Practices Entry: Best Practice Info:a71 Committee Approval Date: 2000-03-28a71 Center Point of Contact: GRCa71 Submitted by: Wilson HarkinsSubject: Design Considerations For Space Trusses Practice: Use the PSAM (Probabilistic Structural Analysis Methods) contained in the computer code NESSUS (N

2、umerical Evaluation of Stochastic Structures Under Stress) to identify and quantify the reliability of space structures.Programs that Certify Usage: This practice has been used on SSME, Space Station.Center to Contact for Information: GRCImplementation Method: This Lessons Learned is based on Reliab

3、ility Practice Number PD-ED-1242; from NASA Technical Memorandum 4322A, NASA Reliability Preferred Practices for Design and Test.Benefits:This practice can be used to determine an optimum truss configuration (e.g. minimum number of members) for a given loading condition and specified reliability. Pr

4、obabilistic Structural Analysis Methods (PSAM) provides a formal and systematic way to evaluate structural performance reliability or risk at minimal time and low cost.Implementation Method:Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-The purpose

5、of this application is to probabilistically evaluate a three-dimensional, three-bay, space cantilever truss by using the computer code NESSUS (Numerical Evaluation of Stochastic Structures under Stress). Using PSAM will enable design engineers to identify and quantify the sensitivities associated wi

6、th uncertainties in primitive variables (structural, material and load parameters) describing the truss. The primitive variables for a given space truss such as stiffness parameters, strength parameters, spatial truss geometry, and applied loads or moments will vary continuously due to changes in th

7、e space environment. Each of these primitive variables distribution is characterized in terms of one of several available probability distributions, such as the Weibull, exponential, normal, log-normal, etc. The cumulative distribution functions for the response functions considered and sensitivitie

8、s associated with the primitive variables for given response are investigated. These distributions have significant impact on the separation/range of the response variables such as nodal displacements, eigen-values, member forces, vibration frequencies, etc. These sensitivities help in determining t

9、he dominating primitive variables for a particular response.Program Capability and DescriptionThe NESSUS code consists of three major modules:(1) NESSUS/PRE (pre-processor) module is used to obtain the characteristic of a partially correlated Gaussian field in terms of a set of uncorrelated random v

10、ectors.(2) NESSUS/FEM (Finite Element Methods) module is a finite element analysis code that can generate perturbed solutions about a deterministic state. It contains an efficient perturbation technique such that the perturbation of each variable is done rapidly. Each perturbation corresponds to a p

11、rescribed deviation from the deterministic model.(3) NESSUS/FPI (Fast Probability Integration) module contains several advanced reliability methods including Monte-Carlo simulation.Since NESSUS/PFEM combined the NESSUS/FEM and NESSUS/FPI modules into a single computer program, the entire probabilist

12、ic finite element analysis including perturbations of the primitive variables can be performed in a single execution step.The fast probability integration (FPI) techniques are one or several orders of magnitude more efficient than the Monte-Carlo simulation methods. FPI module extracts the database

13、of perturbed solutions from NESSUS/FEM to calculate the probability distribution functions of the response variables. In general, the primitive variables are specified with their mean values (m), standard deviation (s), and the type of distribution. Note: Each module can be operated independently.Pr

14、obabilistic Finite Element AnalysisProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-In general, the finite element equation for motion is written as:M + C m + K u = F(t)Equation (1)Where: M denotes mass matrix. C denotes damping matrix. K denotes the

15、stiffness matrix denotes acceleration vector. m denotes velocity vector. u denotes displacement vector.Note: These matrices are calculated probabilistically in the NESSUS code. The forcing function vector, F(t), is time dependent at each node.In this practice, the static case is considered by settin

16、g the mass and damping matrices to zero and considering the forcing function being independent of time in equation (1) such thatK u = FEquation (2)Furthermore, by just setting the damping matrix to zero, eigenvalue analysis can be accomplished by usingK - w2M u = 0Equation (3)where w denote eigenval

17、ues and u are the corresponding eigenvectors.Finite Element ModelA three-dimensional, three-bay cantilever truss is computationally simulated using a linear isoparametric beam element based on the Timoshenko beam formulation. The element is idealized as a two-noded line segment in three-dimensional

18、space. The cantilever truss is assumed to be made from 44 hollow circular tube members (see Fig. 1). The tubes are made up of wrought Aluminum alloy with modulus of elasticity (E) equal to 10 Mpsi. The outer and inner radii (roand ri) of the tube are 0.5 and 0.4375 in., respectively. All 6 degrees-o

19、f -freedom are restrained at the fixed end (left side) nodes. The truss is analyzed twice, once using beam elements and then using pseudo-truss elements. The beam element is converted into a pseudo-truss element by suppressing the effective shear areas in the principal planes (Axxand Ayy), the two p

20、rincipal moments of inertias for the tube Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-cross-section, (Ixxand Iyy), and torsional constant, J. In the case of truss elements, 3 rotational degrees of freedom at each node and 3 translational degrees

21、of freedom at support nodes are restrained.Each bay of the truss is 5 ft wide, 8 ft long, and 6 ft high ( see Fig. 1 ). The overall length of the truss is 24 ft. Six vertical and two longitudinal loads are applied. Twisting moments are applied at the truss-end top nodes for truss elements. The direc

22、tions of the forces and moments are shown in Figure 1 and the mean values are given in Table I.Probabilistic ModelThe following primitive variables are considered in perturbation analysis:( 1 ) Nodal Coordinates ( X, Y, Z ) ( 2 ) Modulus of elasticity ( E ) ( 3 ) Outer radius of the tube (ro) ( 4 )

23、Inner radius of the tube (ri) ( 5 ) Vertical loads ( V ) ( 6 ) Longitudinal loads ( H ) ( 7 ) Truss-end moments ( M ) ( 8 ) Truss-end coupling forces ( P )It is possible that the above primitive design variables will vary continuously and simultaneously due to extreme changes in the environment when

24、 trusses are used in upper Earth orbit for space station type structures. The normal distribution is used to represent the uncertainties in E, ro, ri, and X, Y, Z coordinates.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-refer to D descriptionD The

25、 applied loads, moments and coupling forces are selected to represent anticipated loading conditions for a typical space truss. These are represented by log-normal distributions. Initially, NESSUS/FEM module is used to take into consideration the mean value of these primitive variables. In the subse

26、quent probabilistic analysis each primitive variable is perturbed equidistant from the mean value. However, each variable is perturbed independently and by a different amount. Usually, the perturbed value of the design variable is taken as a certain fraction of the standard deviation at either side

27、of the mean value. Finally, the NESSUS/FPI module extracts response variable values (one deterministic and two times the number of primitive variables) to calculate a probability distribution function of the response variable considered. The mean, distribution type and percentage variation for diffe

28、rent primitive variable are given in Table I.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-refer to D descriptionD Data AnalysisThe three-dimensional, three-bay cantilever truss is probabilistically analyzed and the cumulative probability distribut

29、ions for the truss end displacements, member forces and vibration frequencies are plotted. The sensitivities of the primitive variables on the scatter in the truss structural responses (truss free end displacements, member axial forces and vibration frequencies) are quantified in Table II. Please re

30、fer to the reference articles of this practice for other information/figures such as the probabilistic displacement of the truss free end nodes (top and bottom) in X, Y, and Z directions using the truss element. The cumulative distribution functions of frequencies of modes 1 and 2 using truss elemen

31、ts are plotted (see sample Figure 2, others please refer to the reference articles). Please refer to the reference articles for other valuable information such as data plots for the truss modelled with beam elements. It is important to note from Table II that the cross-sectional area (primitive vari

32、ables roand ri) has a significant impact on the probabilistic distribution of the vibration frequencies. For additional result formats please refer to reference 1.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-refer to D descriptionD refer to D desc

33、riptionD Technical Rationale:Traditional deterministic methods applied to the analysis of space truss design only consider applied loads for given operating condition. To account for uncertainties in assumptions of loading and material strength, load factors and safety factors are applied to assure

34、the final design will satisfy design specifications.This traditional approach to stress analysis does not formally address the natural uncertainties of primitive variables (fundamental parameters describing the structural problem) such as the uncertainties of loading and material strength. Numerous

35、uncertainties associated with truss Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-structures in space environments require a quantitative and systematic method to ascertain that the structural response will be within the acceptable limits during th

36、e life of the structure. Probabilistic structural analysis provides a formal way to properly account for all these uncertainties.Currently available software tools do not easily allow determination of any local instability in any of the internal members of the truss during probabilistic analysis. Th

37、erefore, NASA Lewis Research Center developed PSAM, which provides a formal and systematic way to reliably evaluate structural performance and durability. PSAM takes into account the uncertainty of primitive variables and will yield a stable and optimum configuration for given load conditions. This

38、probabilistic approach also takes into account the uncertainties of primitive variables in the space environment.References1. Pai, S.S., “Probabilistic Structural Analysis of a Truss Typical for Space Station“, NASA Technical Memorandum 103277, 1990.2. Pai, S.S. and Chamis, C.C., “Probabilistic Prog

39、ressive Buckling of Trusses“, NASA Technical Memorandum 105162, 1991.3. Research & Technology - 1992, NASA LeRC TM 105924, 1992.4. Pai, S.S. and Chamis, C.C., “Probabilistic Structural Analysis of Adaptive/Smart/Intelligent Space Structures“, NASA Technical Memorandum 105408, 1991.5. Pai, S.S. and C

40、hamis, C.C., “Probabilistic Assessment of Space Trusses Subjected to Combined Mechanical and Thermal Loads“, NASA Technical Memorandum 105429, 1992.NOTE: Please refer to the attached Software Release Request form for information on how to obtain the NESSUS software.nullImpact of Non-Practice: Aerosp

41、ace structures and spacecraft are complex assemblies of structural components that are subjected to a variety of hazardous conditions. Failure to adhere to proven space truss reliability analysis practices could cause shortened mission life, impact mission success, premature termination of component

42、 or experiment operation, and in extreme circumstance, loss of mission and human life. All phases of space truss design process, from development, design, fabrication and all the way to installation in the spacecraft, must adhere to proven reliable design and safe practices.Related Practices: N/A Ad

43、ditional Info: Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Approval Info: a71 Approval Date: 2000-03-28a71 Approval Name: Eric Raynora71 Approval Organization: QSa71 Approval Phone Number: 202-358-4738Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-