NAVY UFGS-32 12 17-2008 HOT MIX BITUMINOUS PAVEMENT《热拌沥青路面》.pdf

《NAVY UFGS-32 12 17-2008 HOT MIX BITUMINOUS PAVEMENT《热拌沥青路面》.pdf》由会员分享，可在线阅读，更多相关《NAVY UFGS-32 12 17-2008 HOT MIX BITUMINOUS PAVEMENT《热拌沥青路面》.pdf（27页珍藏版）》请在麦多课文档分享上搜索。

1、*USACE / NAVFAC / AFCESA / NASA UFGS-32 12 17 (April 2008)-Preparing Activity: NAVFAC Replacing without changeUFGS-32 12 17 (April 2006)UNIFIED FACILITIES GUIDE SPECIFICATIONSReferences are in agreement with UMRL dated March 2008*SECTION TABLE OF CONTENTSDIVISION 32 - EXTERIOR IMPROVEMENTSSECTION 32

2、 12 17HOT MIX BITUMINOUS PAVEMENT04/08PART 1 GENERAL1.1 REFERENCES1.2 SUBMITTALS1.3 QUALITY ASSURANCE1.3.1 Safety Requirements1.3.2 Mock-Up Test Section1.3.3 Required Data1.3.4 Charts1.3.5 Selection of Optimum Asphalt Content1.4 DELIVERY, STORAGE, AND HANDLING1.5 ENVIRONMENTAL CONDITIONS1.6 CONSTRUC

3、TION EQUIPMENT1.6.1 Mixing Plant1.6.1.1 Cold Aggregate Feeder1.6.1.2 Dryer1.6.1.3 Plant Screens and Bins for Batch and Continuous Mix Plants1.6.1.4 Testing Laboratory1.6.1.5 Surge and Storage Bins1.6.1.6 Drum-Dryer Mixer1.6.2 Paving Equipment1.6.2.1 Spreading Equipment1.6.2.2 Rolling Equipment1.6.2.

4、3 Hand Tampers1.6.2.4 Mechanical Hand TampersPART 2 PRODUCTS2.1 AGGREGATES2.1.1 Coarse Aggregates2.1.2 Fine Aggregate2.1.3 Mineral Filler2.1.4 Aggregate Gradation2.2 ASPHALT CEMENT BINDER2.3 MIX DESIGN2.3.1 JMF RequirementsSECTION 32 12 17 Page 1Provided by IHSNot for ResaleNo reproduction or networ

5、king permitted without license from IHS-,-,-2.3.2 Adjustments to JMF2.4 RECYCLED HOT MIX ASPHALT2.4.1 RAP Aggregates and Asphalt Cement2.4.2 RAP Mix2.5 SOURCE QUALITY CONTROL2.5.1 Tests2.5.2 SpecimensPART 3 EXECUTION3.1 PREPARATION3.1.1 Preparation of Asphalt Binder Material3.1.2 Preparation of Mine

6、ral Aggregates3.1.3 Preparation of Bituminous Mixture3.1.4 Transportation of Bituminous Mixtures3.1.5 Surface Preparation of Underlying Course3.1.6 Spraying of Contact Surfaces3.2 PLACEMENT3.2.1 Machine Spreading3.2.2 Shoveling, Raking, and Tamping After Machine-Spreading3.2.3 Hand-Spreading in Lieu

7、 of Machine-Spreading3.3 COMPACTION OF MIXTURE3.4 JOINTS3.4.1 Transverse3.4.2 Longitudinal Joints3.5 FIELD QUALITY CONTROL3.5.1 Sampling3.5.1.1 Aggregates At Source3.5.1.2 Cold Feed Aggregate Sampling3.5.1.3 Coarse and Fine Aggregates3.5.1.4 Mineral Filler3.5.1.5 Pavement and Mixture3.5.2 Testing3.5

8、.2.1 Aggregates Tests3.5.2.2 Bituminous Mix Tests3.5.2.3 Pavement Courses3.6 PROTECTION- End of Section Table of Contents -SECTION 32 12 17 Page 2Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-*USACE / NAVFAC / AFCESA / NASA UFGS-32 12 17 (April 200

9、8)-Preparing Activity: NAVFAC Replacing without changeUFGS-32 12 17 (April 2006)UNIFIED FACILITIES GUIDE SPECIFICATIONSReferences are in agreement with UMRL dated March 2008*SECTION 32 12 17HOT MIX BITUMINOUS PAVEMENT04/08*NOTE: This guide specification covers the requirements for hot-mix asphalt pa

10、vement for leveling, binder, and wearing courses using virgin materials.Edit this guide specification for project specific requirements by adding, deleting, or revising text. For bracketed items, choose applicable items(s) or insert appropriate information.Remove information and requirements not req

11、uired in respective project, whether or not brackets are present.Comments and suggestions on this guide specification are welcome and should be directed to the technical proponent of the specification. A listing of technical proponents, including their organization designation and telephone number,

12、is on the Internet.Recommended changes to a UFGS should be submitted as a Criteria Change Request (CCR).*NOTE: This guide specification is not intended for use in hot-mix recycling.*NOTE: The following information shall be shown on drawings:1. Layout and geometry of paving.2. Cross section and thick

13、ness of paving.*NOTE: Retain only the desired mixes in leveling, binder, and wearing courses. For airfield projects, SECTION 32 12 17 Page 3Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-aggregate gradations shall be as shown in Table I . For vehicu

14、lar pavement, show gradations for vehicular pavement from local state highway department (as appropriate to the Marshall Method for Design and Control of Bituminous Paving Mixtures). Generally, the maximum size of aggregate for wearing course should not exceed 40 percent of the designed thickness of

15、 the course (i.e., course thickness divided by 2.5); in no case should the aggregate size exceed 25 mm one inch or one-half the thickness of the compacted wearing course or two-thirds the thickness of any binder or leveling course; gradation requirements for the leveling course should be specified t

16、o suit the project and may vary from a fine wearing course mix to a coarse binder course mix as dictated by project requirements. When appropriate, the wearing course mix may be specified as an option for the leveling and/or binder course mixes.*PART 1 GENERAL1.1 REFERENCES*NOTE: This paragraph is u

17、sed to list the publications cited in the text of the guide specification. The publications are referred to in the text by basic designation only and listed in this paragraph by organization, designation, date, and title.Use the Reference Wizards Check Reference feature when you add a RID outside of

18、 the Sections Reference Article to automatically place the reference in the Reference Article. Also use the Reference Wizards Check Reference feature to update the issue dates.References not used in the text will automatically be deleted from this section of the project specification when you choose

19、 to reconcile references in the publish print process.*The publications listed below form a part of this specification to the extent referenced. The publications are referred to within the text by the basic designation only.AMERICAN ASSOCIATION OF STATE HIGHWAY AND TRANSPORTATION OFFICIALS (AASHTO)A

20、ASHTO MP 1a (2004) Performance Graded Asphalt BinderASPHALT INSTITUTE (AI)AI MS-02 (6th Edition; 1997) Mix Design Methods for AsphaltSECTION 32 12 17 Page 4Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ASTM INTERNATIONAL (ASTM)ASTM C 117 (2004) Sta

21、ndard Test Method for Materials Finer than 75-um (No. 200) Sieve in Mineral Aggregates by WashingASTM C 127 (2007) Standard Test Method for Density, Relative Density (Specific Gravity), and Absorption of Coarse AggregateASTM C 128 (2007a) Standard Test Method for Density, Relative Density (Specific

22、Gravity), and Absorption of Fine AggregateASTM C 131 (2006)Standard Test Method for Resistance to Degradation of Small-Size Coarse Aggregate by Abrasion and Impact in the Los Angeles MachineASTM C 136 (2006) Standard Test Method for Sieve Analysis of Fine and Coarse AggregatesASTM C 188 (1995; R 200

23、3) Standard Test Method for Density of Hydraulic CementASTM C 29/C 29M (2007) Standard Test Method for Bulk Density (“Unit Weight“) and Voids in AggregateASTM C 88 (2005) Standard Test Method for Soundness of Aggregates by Use of Sodium Sulfate or Magnesium SulfateASTM D 1073 (2007) Fine Aggregate f

24、or Bituminous Paving MixturesASTM D 1188 (2007) Bulk Specific Gravity and Density of Compacted Bituminous Mixtures Using Paraffin-Coated SpecimensASTM D 140 (2001; R 2007) Sampling Bituminous MaterialsASTM D 1559 (1989) Resistance to Plastic Flow of Bituminous Mixtures Using Marshall ApparatusASTM D

25、 2041 (2003a) Theoretical Maximum Specific Gravity and Density of Bituminous Paving MixturesASTM D 2172 (2005) Quantitative Extraction of Bitumen from Bituminous Paving MixturesASTM D 242 (2004) Mineral Filler for Bituminous Paving MixturesASTM D 2726 (2005a) Bulk Specific Gravity and Density SECTIO

26、N 32 12 17 Page 5Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-of Non-Absorptive Compacted Bituminous MixturesASTM D 3381 (2005) Viscosity-Graded Asphalt Cement for Use in Pavement ConstructionASTM D 4867/D 4867M (2004) Effect of Moisture on Asphal

27、t Concrete Paving MixturesASTM D 546 (2005) Sieve Analysis of Mineral Filler for Bituminous Paving MixturesASTM D 692 (2000; R 2004) Coarse Aggregate for Bituminous Paving MixturesASTM D 70 (2003) Specific Gravity and Density of Semi-Solid Bituminous Materials (Pycnometer Method)ASTM D 75 (2003) Sta

28、ndard Practice for Sampling AggregatesASTM D 854 (2006e1) Specific Gravity of Soil Solids by Water PycnometerASTM D 946 (1982; R 2005) Penetration-Graded Asphalt Cement for Use in Pavement ConstructionASTM D 979 (2001; R 2006e1) Sampling Bituminous Paving MixturesASTM D 995 (1995b; R 2002) Mixing Pl

29、ants for Hot-Mixed, Hot-Laid Bituminous Paving Mixtures1.2 SUBMITTALS*NOTE: Review submittal description (SD) definitions in Section 01 33 00 SUBMITTAL PROCEDURES and edit the following list to reflect only the submittals required for the project. Submittals should be kept to the minimum required fo

30、r adequate quality control.A “G” following a submittal item indicates that the submittal requires Government approval. Some submittals are already marked with a “G”. Only delete an existing “G” if the submittal item is not complex and can be reviewed through the Contractors Quality Control system. O

31、nly add a “G” if the submittal is sufficiently important or complex in context of the project.For submittals requiring Government approval on Army projects, a code of up to three characters within the submittal tags may be used following the “G“ designation to indicate the approving authority. Codes

32、 for Army projects using the Resident Management System (RMS) are: “AE“ for SECTION 32 12 17 Page 6Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Architect-Engineer; “DO“ for District Office (Engineering Division or other organization in the Distric

33、t Office); “AO“ for Area Office; “RO“ for Resident Office; and “PO“ for Project Office. Codes following the “G“ typically are not used for Navy, Air Force, and NASA projects.Choose the first bracketed item for Navy, Air Force and NASA projects, or choose the second bracketed item for Army projects.*

34、Government approval is required for submittals with a “G“ designation; submittals not having a “G“ designation are for Contractor Quality Control approval.for information only. When used, a designation following the “G“ designation identifies the office that will review the submittal for the Governm

35、ent. The following shall be submitted in accordance with Section 01 33 00 SUBMITTAL PROCEDURES: SD-04 Samples*NOTE: Include requirements for test sections in all projects with 4,500 metric tons 5,000 tons or more of asphaltic concrete. Test sections may be considered necessary and specified in small

36、er projects if the pavement structure is critical and the cost of a test section is deemed to be justified. Normally, a test section is required only for the wearing course. If it is deemed necessary to test other courses, the specifications must be modified to suit.*Bituminous pavementSD-05 Design

37、DataJob-mix formulaSubmit a job-mix formula, prepared specifically for this project within one year of submittal for roads, for approval by the Government prior to preparing and placing the bituminous mixture. Design mix using procedures contained in Chapter V, Marshall Method of Mix Design, of AI M

38、S-02. Formulas shall indicate physical properties of the mixes as shown by tests made by a commercial laboratory approved by the Contracting Officer, using materials identical to those to be provided on this project. Submit formulas with material samples. Job-mix formula for each mixture shall be in

39、 effect until modified in writing by the Contractor and approved by the Contracting Officer. Provide a new job-mix formula for each source change. Submittal shall include all tests indicated in MIX DESIGN section of this specification.ASPHALT CEMENT BINDERMIX DESIGNSECTION 32 12 17 Page 7Provided by

40、 IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SD-06 Test ReportsSpecific gravity test of asphaltCoarse aggregate testsWeight of slag testPercent of crushed pieces in gravelFine aggregate testsSpecific gravity of mineral fillerBituminous mixture testsAggregate

41、s testsBituminous mix testsPavement coursesSubmit in accordance with paragraph entitled “Mock-Up Test Section.“1.3 QUALITY ASSURANCE1.3.1 Safety RequirementsProvide adequate and safe stairways with handrails to the mixer platform, and safe and protected ladders or other means for accessibility to pl

42、ant operations. Guard equipment and exposed steam or other high temperature lines or cover with a suitable type of insulation.1.3.2 Mock-Up Test Section*NOTE: Include requirements for test sections in all projects with 4,500 metric tons 5,000 tons or more of asphaltic concrete. Test sections may be

43、considered necessary and specified in smaller projects if the pavement structure is critical and the cost of a test section is deemed to be justified. Normally, a test section is required only for the wearing course. If it is deemed necessary to test other courses, the specifications must be modified to suit.*Prior to full production of the binder and wearing courses, prepare a quantity of bituminous mixture according to the job-mix formula. Construct a test section 60 m 200 feet long by not less than 3 m 10 feet wide and of the same compacted depth specifi