NAVY MMM-A-185 B (3)-1999 ADHESIVE RUBBER (FOR PAPER BONDING)《用于粘纸的橡胶粘合剂》.pdf

《NAVY MMM-A-185 B (3)-1999 ADHESIVE RUBBER (FOR PAPER BONDING)《用于粘纸的橡胶粘合剂》.pdf》由会员分享，可在线阅读，更多相关《NAVY MMM-A-185 B (3)-1999 ADHESIVE RUBBER (FOR PAPER BONDING)《用于粘纸的橡胶粘合剂》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、NOT MEASUREMENT SENSITIVEMMM-A-185BAMENDMENT 3July 15, 1999SUPERSEDINGINTERIM AMENDMENT 2April 16, 1975FEDERAL SPECIFICATIONADHESIVE, RUBBER (FOR PAPER BONDING)The General Services Administration has authorized the use of this amendmentwhich forms a part of MMM-A-185B, dated November 4, 1974, by all

2、 federal agencies.PAGE 22.2, line 5: Delete “D56 Flash Point by Tag Closed Tester.”3.1.1.2: Delete in its entirety and substitute:“3.1.1.2 The volatile solvent when tested as specified in 4.4.2 shall conform byvolume to the requirements controlling the emission of solvents into the atmosphere ascall

3、ed out in (a), (b), (c), (d), and (e) (see 4.3.3).(a) A combination of aldehydes or branched chain ketones : 20 percent maximum.(b) A combination of aromatic compounds with eight or more carbon atoms to themolecule except ethylbenzene : 8 percent maximum.(c) A combination of ethylbenzene or toluene

4、: 20 percent maximum.(d) A combination of solvents with an olefinic or cyclo-olefinic type of unsaturation:5 percent maximum.(e) Total of (a) + (b) + (c) + (d) = 20 percent maximum.”AMSC N/A 1 of 2 FSC 8040DISTRIBUTION STATEMENT A . Approved for public release; distribution is unlimited.Provided by

5、IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MMM-A-185BAMENDMENT 32PAGE 33.5, line 1 : Delete “400” and substitute “4000.”3.11: Delete in its entirety.3.12, line 1 : Delete “3.12” and substitute “3.11.”PAGE 64.4.6: Delete in its entirety and substitute:“4.4.6

6、 Viscosity. The viscosity of the adhesive shall be determined in accordancewith method B of ASTM D 1084 to determine compliance with the requirement of 3.3. ABrookfield Synchro-Lectric viscosimeter, model RVF, or equal, equipped with a No. 2spindle and operated at 4 rpm shall be used.”4.4.13: Delete

7、 in its entirety.PAGE 7* 5.1.1.1.1, line 3 : Delete “tin-copper alloy, tin-lead alloy, or.”NOTE: The margins of this amendment are marked with asterisks to indicate where changesfrom the previous amendment were made. This was done as a convenience only and theGovernment assumes no liability whatsoev

8、er for any inaccuracies in these notations. Biddersand contractors are cautioned to evaluate the requirements of this document based on the entirecontent irrespective of the marginal notations and relationship to the last previous amendment.MILITARY INTERESTS: CIVIL AGENCYCOORDINATING ACTIVITY:Custodians:Navy AS GSA FSSArmy MRAir Force 99 Preparing activity:Navy ASReview activity: Navy MC (Project 8040-0705)Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-