NAVY MIL-T-87099-1987 TROUSERS WET WEATHER《潮湿天气穿裤子》.pdf

《NAVY MIL-T-87099-1987 TROUSERS WET WEATHER《潮湿天气穿裤子》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-T-87099-1987 TROUSERS WET WEATHER《潮湿天气穿裤子》.pdf（33页珍藏版）》请在麦多课文档分享上搜索。

1、C 184-65 14 October 1987 MIL-T-87099 .- .a MILITARY SPECIFICATION TROUSERS, WET WEATHER This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCQPE 1.1 Scope. This specification covers the requirements for waterproof trousers, made ofa double coated

2、nylon twill cloth. 1.2 Classification. The trousers shall be of one type, and shall be procured in the following sizes as specified (see 6.2): XX Small - (20-22) X Small - (24-26) Small - (28-30) Medi um - (32-34) Large - (36-38) X-Large - (40-42) 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.

3、1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Sp

4、ecifications and Standards (DoDISS) and supplement therto, cited in the solicitation. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this, document should be addressed to: Officer in Charge, Navy Clothing and Textile Research Facil

5、ity, 21 Strathmore Road, Natick, MA 01760-2490 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC/NA FSC 8405 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. THIS DOCUMENT

6、 CONTAINS 33 PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-87099 J SPEC IF ICATIONS FEDERAL V-T-295 - Thread, Nylon NN-P-7 1 - Pallet, Material Handling, Wood, Stringer JJ-W-155 - Webbing, Textile, (Cotton, Elastic) DDD-L-20 - Label; F

7、or Clothing, Equipage, and Tentage (General Construction, 2 Way and 4 Way (Partial) Use) MIL ITAKY MIL-B-286 - Button, Tack; and Tack, Button MIL-F-495 - Finish, Chemical, Black (For Copper Alloys) MIL-W-5664 - Webbing, Z-xtile, Elastic, Cotton MIL-P-150 11 - Pallet, Material Handling, Wood, Post Co

8、nstruction, 4 Way Entry MIL-B-17757 7. Boxes, Shipping, Fiberboard (Modular Sizes) MIL-C- 1 9 7 59 - Cloth, Coated, Twill, Nylon (Low Count) MIL-F-21840 - Fastener Tapes, Hook and Pile, Synthetic STAN DARDS FEDERAL FED-STD-191 - Textile Test Methods FED-STD-7 5 1 - Stitches, Seams, and Stitchings MI

9、LITARY MIL-STD-105 - Sampling Procedures and Tables for Inspection by Attributes MIL-STD-129 - Marking for Shipment and Storage MIL-STD-147 - Palletized Unit Loads (Copies of specifications, standards, drawings, and publications required by contractors in connection with specific procurement functio

10、ns should be obtained from the procuring activity or as directed by the contracting officer). 2.1.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this specification to the extent specified herein. Unless ot

11、herwise specified, the issues shall be those in effect on the date of the solicitation. LAWS AND REGULATIONS US POSTAL SERVICE MANUAL (Copies of the manual may be obtained from the Superintendent of Documents, US Government Printing Office, Washington, DC 20402). 2 Provided by IHSNot for ResaleNo re

12、production or networking permitted without license from IHS-,-,- - MIL-T-87077 8LJ W 7777906 0411175 8 m - - . MIL-T-87099 2.2 Other publications. The following document(s) form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of documents which are

13、 DoD adopted shall be those listed in the issue of the DoDISS specified in the solicitation. Unless otherwise specified, the issues of documents not listed in the DoDISS shall be the issue of the nongovernment documents which is current on the date of the solicitation. NATIONAL MOTOR FREIGHT TRAFFIC

14、 ASSOCIATION, INC., AGENT Nat i o na1 Mo t o r Frei g h t C1 as s i f i cat i on (Applications for copies should be addressed to the American Trucking Association, ATTN: Traffic Department, 1616 P Street, N.W., Washington, DC 20036) UNIFORM CLASSIFICATION COMMITTEE, AGENT Uniform Freight Classificat

15、ion (Applications for copies should be addressed to the Uniform Classification Committee, Room 1106, 222 South Riverside Plaza, Chicago, Illinois 60606). 2,3 Order of precedence. In the event of a conflict between the text of this specification and the references cited herein, the text of this speci

16、fication shall take precedence. Nothing in this specification, howeyer, shall supersede applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Guide sample. Samples, when furnished, are solely for guidance and information to the contractor (see 6.3). Varia

17、tions from this specification mag appear in the sample in which case this specification shall govern. 3.2 First article. When specified, the contractor shall furnish sample unit(s) for first article inspection and approval (see 4.3 and 6.2). 3.3 Naterial. 3.3.1 Basic material, The basic material for

18、 the trousers shall be a chloroprene coated nylon twil-l- conforming to Type 11 of MIL-C-19759, except that the coating shall be unvulcanized. The cloth shall be tested as specified in 4.4.1. 3.3.2 Buttons and tacks. The buttons and tacks for suspender attachment shall conform to the requirements sp

19、ecified in MIL-B-286. The buttons shall be of Type I, 27 line, and the tacks shall be of Type IX, 14 line by 0.406 inch prong length. 3.3.3 Cement, chloroprene. The cementing compound shall have a chloroprene base and the same curing characteristics as the coating compound specified in 3.3.1. The us

20、e of reclaimed rubber is prohibited (see 4.4.1). Cemented sample seams shall have a minimum adhesion of 5 pounds per inch width when tested as specified ia 4.4.1. The color of the cement shall approximate the 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from

21、 IHS-,-,-MIL-T-87099 shade of the green coating compound specified in 3.3.1 or shall be unpigmented. 3.3.4 Thread, nylon. The nylon thread used for all seaming and stitching shall conform to Type III, Size B or E, of V-T-295, except that the colorfastness requirements shall not apply. The color shal

22、l approximate the green shade of the basic material. 3.3.5 Fastener tapes. The fastener tapes shall conform to Type II, Class 3 or 5, of MIL-F-21840. Unless otherwise specified, the tapes shall be 1 inch in width. The color shall be Green 3422. 3,3.6 Buckles, suspender. The buckles shall be made of

23、brass and shall be chemically finished black conforming to the requirements of MIL-F-495. The shape and dimensions of the suspender buckles shall be as shown in Figure 2. 3.3.7 Suspender webbing, The webbing shall be 1 1/2 inch wide cotton elastic conforming to Class 2, of MIL-W-5664. The color shal

24、l be black, white or natural or shall approximate the green shade of the basic material. 3.3.8 Webbing, elastic. The elastic webbing for the trouser waist shall conform to Type I, Class 3 or 4, of JJ-W-155. Class 4 webbing shall be black. Class 3 webbing shall be unbleached, bleached, or dyed any sh

25、ade. 3.3.9 Bias tape. The bias tape used as stay stripping or seam strapping shall be any suitable plain woven fabric, weighing not less than 2.5 OZ. per square yard (see 4.4.1). The cloth shall be dyed to harmonize with the shade of the back side of the basic cloth and bias cut to the width require

26、d (see Table I). Any continuous length used for the construction of the trousers shall contain not more than two seams. As an alternate, the basic material specified in 3.3.1 may be used. When basic material is used, any continuous length shall not be spliced or seamed. 3.3.10 Combination label . A

27、combination identification, size, and instruction label, conforming to Type IV, Classes 12 and 13, of DDD-L-20, shall be printed on a suitable sized piece of unvulcanized basic material or may be marked directly on the trousers. All markings shall be bright yellow In color. The inscription shall be

28、as follows: TROUSERS, WET WEATHER CONTRACT NO. DLA-100-00-0-0000 (EXAMPLE) STOCK NO. 8405-00-000-0000 (EXAMPLE) SIZE: MEDIUM (32-34) (EXAMPLE) NAME OF CONTRACTOR INSTRUCTIONS THESE WATERPROOF TROUSERS HAVE BEEN OVERSIZED TO FIT OVER HEAVY CLOTHING FOR USE UNDER COLD/ WET WEATHER CONDITIONS. IF TOO L

29、ARGE WHEN WORN OVER LIGHT CLOTHING, USE A SMALLER SIZE. RINSE GARMENT WITH A HOSE OR SPONGE USING FRESH WATER AFTER EVERY USE DO NOT DRY CLEAN. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-67077 Li U 777770b OLiLLL77 L MIL-T-87099 3.3.11 D

30、usting medium. The dust used in fabricating both the basic material and trousers, shall be applied in the smallest quantity necessary to prevent blocking. The dust shall consist of a finely powdered mineral material such as talc, except that the addition of zinc stearate to the medium is permissible

31、 in an amount that will not support mildew growth on the finished vulcanized trousers (see 4.4.1). 3.4 Design. The trousers shall be of an elastized, high-waisted style, with cemented and vulcanized inseams and crotch seams, patch pockets and hemmed l.eg bottoms. The ends of the adjustable elastic s

32、uspenders shall be stitched- to the back of the trousers. The slide loop buckles shall fasten to the buttons positioned on each side of the trouser front. The two back patch pockets see 3.3.9). The V-stay strips shall consist of a 7/8 to 1 inch width of bias tape or basic material folded in half len

33、gthwise and permanently creased. C. Encase the side and bottom of the templates described in “6a. with the inside surfaces of the V-stay strips. Ends of the V-stay strips shall extend 1/4 to 3/8 inch beyond the top of the templates. d. Apply cement to the trouser fronts by means of the cement marker

34、 template in the areas where pockets are to be affixed. e. Position the templates prepared as specified in 6c. onto the trousers so that the top of the templates are even with theapocket placement marks on the trousers. The templates shall be cemented so that the cemented areas on the trousers are o

35、f even width around the outside of the templates. OSf 10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-T-87097 8L( W 7979906 0433203 3 MIL-T-87099 TABLE I - CONSTRUCTION OF TROUSERS THREAD NO. OPERATION STCH SEAM/ STCH NDL BOB/ TYPE STCH TYPE

36、IN LPR f. Activate the cement applied in operation 5c. around the back of the packet assemblies with an appropriate solvent. Place each pocket assembly over the respective template and secure pocket sides and bottoms to the trousers and V-stay strips in accordance with pattern marks. The tops of the

37、 pocket assemblies shall be left free. g. Remove templates, leaving the V-stay strips in place and affix the tops of the pocket assemblies to the trousers. 7. Join inseams and crotch seams. a. Seams shall be cemented in the following manner (see Figure 4 and 3.6.3). 1, Apply cement over a 3/4 to 7/8

38、 inch width along each surface to be joined. Cement may be allowed to dry and be dusted and reactivated with an appropriate solvent before the seam is joined . LSb j 2. Cemented ace and back surfaces shall be joined by overlapping in the specified direction 1/2 to 3/4 inch. The cemented areas shall

39、extend 1/4 to 3/8 inch beyond the lapped edge of the seam on both the front and back of the garment. 3. Roll seam flat. There shall be no puckers, pleats or areas of poor adhesion. bo Join crotch seams from top of waist to crotch, lapping left over right for both front and back. C. Join inseams, lap

40、ping front over back, matching crotch seams and leg bottoms. 80 Hem trousers. a, Apply cement from edge of each leg bottom to 1 1/4 to 1 1/2 inches in from edge on the inside of trousers. b. Fold under leg bottom 1/2 to 3/4 inch to form a hem. Roll flat to ensure adhesion. LSa LSa EFa 11 Provided by

41、 IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I MIL-T-7099 L( W 9999906 OLlL12OL( 5 W MIL-T-8 70 99 TABLE I - CONSTRUCTION OF TROUSERS THREAD e NO O PERAT ION STCH SEAM/ STCH NDL BOB/ TYPE STCH TYPE IN LPR C. As an alternate, trouser hems may be folded under

42、1/2 to 3/4 inch and stitched close to the raw edge. 9 Label (see 3.3.10). Cement the combination identification - size - instruction label or print label inscription directly on inside of trousers, 4 to 4 1/8 . inches, below the top edge and 1 to 1 1/8 inches from the center back seam on tire right

43、side of the trousers. 10. Finish top of trousers. a. The webbing for the suspender straps (see 3.3.7) shall be 41 1/2 (i 1/4) inches long for sizes XXS and XS and 45 1/2 (+ 1/4) inches long for sizes S through XL. $ias cut one end of the strap (approximately 45 angle) and gum the ends with cement (s

44、ee 3.3.3) to prevent raveling. b. Cross the suspender straps (left over right) at a distance of 7 1/2 (+ 1/2, - O) inches from the uncut ends of the straps. Stitch together with a diamond stitch (see Figure 3). The outer row of stitching shall be 1/8 (+ - 1/32) inch from the edges of webbing. c. Rei

45、nforce the top and bottom ends of the diamond stitch with horizontal bartacks (see Figure 3). d. Fold top of trousers to inside, 1 to 1 1/4 inches from the edge, placing the uncut ends of the suspender straps within the fold where indicated by pattern marks on each side of center back. Stitch around

46、 top of trousers within 1/4 inch of raw edge, catching the suspender straps securely in the stitching. 301 EFa-1 8-10 B B EE or or LSb j BB 30 1 SSa-1 6-8 or or EE 301 Brtck 21-28 B B stchs/ or or Brtck E E 301 SSbc-1 8-10 B B or or EE 12 Provided by IHSNot for ResaleNo reproduction or networking pe

47、rmitted without license from IHS-,-,-MIL-T-87099 4 9999906 O411205 7 W Fi IL-T -8 7 O 9 9 TABLE I - CONSTRUCTION OF TROUSERS THREAD NO OPERATION STCH SEAM/ SICH NDL BOB/ TYPE STCH TYPE IN LPR e. Turn straps up to their finished positions 301 bx stch 8-10 B B against the folded portion of trouser top

48、. or or Secure suspenders to back of trousers with a 1 EE 1/4 inch wide by 3/4 inch high boxstitch. The top row pf box-stitching shall finish- 1/8 to 3/16 inch from the top folded edge of trousers f Elastic or the waist (see. 3.3.8) shall be cut in the following relaxed lengths: (+ 1 inch tolerance)

49、. XXS - 17 inches M - 25 inches XS - 19 inches L - 29 inches S - 21 inches XL- 33 inches g. Stitch the appropriate length of 3/4 inch 301 LSbj-2 8-10 B B wide elastic webbing around the waist with two or or rows of stitching, starting and ending at the EE center back seam, positioning the lower edge of the webbing. at the waistline as indicated by pattern marks. The top edge of the webbing -shall finish 1/4 to 3/8 inch below the raw