NAVY MIL-T-60680 A-1993 THRUSTER CARTRIDGE ACTUATED M16 REMANUFACTURED METAL PARTS ASSEMBLY《M16改造金属零件集合发动弹药筒推进器》.pdf
《NAVY MIL-T-60680 A-1993 THRUSTER CARTRIDGE ACTUATED M16 REMANUFACTURED METAL PARTS ASSEMBLY《M16改造金属零件集合发动弹药筒推进器》.pdf》由会员分享,可在线阅读,更多相关《NAVY MIL-T-60680 A-1993 THRUSTER CARTRIDGE ACTUATED M16 REMANUFACTURED METAL PARTS ASSEMBLY《M16改造金属零件集合发动弹药筒推进器》.pdf(13页珍藏版)》请在麦多课文档分享上搜索。
1、L MIL-T-bOb0A 9%0b 19471.59 TOT MIL-T-60680A 12 Amil 1993 SUPERSEDING MIL-T-60680 24 April 1967 MILITARY SPECIFICATION THRUSTER, CARTRIDGE ACTUATED, M16 REMANUFACTURED METAL PARTS ASSEMBLY his specijcation is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1
2、 Scope. This specification covers the requirements for the M16 Cartridge Actuated Thruster Remanufactured Metal Parts Assembly (see 6.1). 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications and standards. The following specifications and standards form a part of this document to t
3、he extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplements thereto, cited in the solicitation (see 6.2). SPECIFICATIONS MILITARY MIL-A-2550 Ammunition,
4、 General Specification For STANDARDS MILITARY MIL-STD-105 MIL-STD-109 MIL-STD-413 Sampling Procedures And Tables For Inspection By Attributes Quality Assurance Terms And Definitions Visual Inspection Guide for Elastomeric O-rings Beneficial comments (recommendations, additions, deletions) and any pe
5、rtinent data which may be of use in improving this document shoukl be addressed to: Coder, Indian Hd Division, Naval Surface Warfare Center, Standardization Branch (Caie 8420), 101 Strauss Avenue, Indian Head, MD 20640-5000, by using the Standardization Document Improvement Proposal (DD Form 1426) a
6、ppearing at the end of this document or by sending a letter. AMSC NIA FSC 1377 DISTRIBUTION STATEMENT A: Approved for public release; distribution is unlimited. Licensed by Information Handling ServicesMIL-T40680A (Unless otherwise indicated, copies of federal and military specifications and standar
7、ds are available from Standardization Documents Order Desk, Bldg. 4D, 700 Robbins Avenue, Philadelphia, PA 191 11-5094,) 2.1.2 Other Government documents, drawings, and publications. The following Government drawings form a part of this specification to the extent specified herein. Unless otherwise
8、specified, the issues are those cited in the solicitation (see 6.2). DRAWINGS Naval Surface Warfare Center, Indian Head (CAGE Codes 19200 and 19203) 1052 1322 Thruster, Cartridge Actuated, M16, Metal Parts Assembly 8845243 Box, Packing, Ammunition, For Thruster, Cartridge Actuated, M16 8845244 Box,
9、Fiberboard (Inner), Packing, Ammunition, For Thruster, Cartridge Actuated, M16 92 17557 Box, Fiberboard (Outer), Alternative, Packing Ammunition, for Thruster, Cartridge Actuated, M16 U.S. Air Force TPO 00-849-0214 Thruster, Cartridge Actuated, M16 (Application for copies should be addressed to: Com
10、mander, Indian Head Division, Naval Surface Warfare Center, Attn: Data Control Branch (Code 8410), Indian Head, MD 20640-5035.) 2.2 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing i
11、n this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Materials. All materials used in the manufacture of the thrusters shall conform to the specifications referred to on the respective drawings unless specific approva
12、l in writing covering a departure therefrom has been obtained fiom the cognizant Navy design activity prior to manufacture. When alternate materials or methods of manufacture are specified on the drawings, the bidders selections shall be clearly stated in the proposal. The remanufactured thruster me
13、tal parts assembly shall contain the following new parts or items: shear pin, O-rings, quad rings, setscrews, spring, silicone fluid, nylon pellets, and lock nut. 3.2 Hydrostatic pressure. The cylinder and head shall withstand a hydrostatic pressure of 10,ooO pounds per square inch (psi) for 15 seco
14、nds, minimum, without leaking, deformation, or mechanical failure (see 6.3.1). 2 * O e O Licensed by Information Handling Services - - flIL-T-6068OA 9999906 39491163 668 MIL-Td0680A 3.3 Protective finish. Protective finish shall be in accordance with the applicable specifications and drawings and sh
15、all apply to all surfaces of the component regardless of configuration. Remanufactured exterior components (see 6.3.2) shall have the existing protective finish stripped and the specified protective finish reapplied. When there are only small surface areas of exposed base metal on the aluminum exter
16、ior components (body assembly and end cap) it may be permissible to treat the surfaces with chemical film Class 1A as specified in MIL-C-5541. 3.4 Residual magnetism. The metal parts assembly shall not deflect the indicator of the compass more than five degrees in either direction using the procedur
17、es of 4.5.5. 3.5 Shear pin strength. The shear pin, after application of protective finish, shall shear when a load of 41 however, this does not authorize submission of known defective material, either indicated or actual, nor does it commit the Government to acceptance of defective material. 4.1.2
18、Quality assurance terms and definitions. Reference shall be made to MIL-STD-109 to define the quality assurance terms used. 4.1.3 Inspections. Inspections shall be in accordance with MIL-A-2550. 4.2 Inspection conditions. Unless otherwise specified (see 6.2), all inspections shall be performed under
19、 the following conditions: a. b. Altitude: sea level c. d. Atmospheric pressure: 14.7 psi Temperature: room ambient (68 to 77F) Humidity: 50 percent relative, maximum 4.3 Quality conformance inspection. 4.3.1 Lot. 4.3.1.1 Submission of product. Unless otherwise specified by the contracting activity,
20、 formation and identification of lots shall be in accordance with MIL-STD-105. 4.3.1.2 Size of lot. For the purpose of identification and shipment, the shipping lots of metal parts assemblies shall consist of 1200 assemblies, maximum, provided the homogeneity requirements of inspection lots have bee
21、n retained. 4 Licensed by Information Handling ServicesHIL-T-bOb80A m 9999706 3949363 430 = MIL-T-60680A 4.3.2 Examination. On reprocessed parts, one hundred percent examination shall be performed for all critical defects. Examination for major and minor defects shall be performed on a defect basis
22、in accordance with the classification of defects. Four power (4x) magnification may be used in performing visual examination for such defects as burr and foreign matter. Inspection for rubber O-rings shall be in accordance with MIL-STD-413. When compliance with the applicable requirement is in doubt
23、 as a result of visual examination, the characteristic shall be measured or gaged to determine acceptability. All nonconforming material shall be rejected. 0 4.3.2.1 Examination of reclaimed parts. Examination of reusable parts, which require no reprocessing, shall be limited to inspection of defect
24、s that require visual type inspection. One hundred percent examination shall be performed for all such defects. All nonconforming parts shall be reprocessed or rejected. 4.3.2.2 Pin, Firing, Drawing 8596416, covering a detail of Drawing 10521322. Characteristics Defect Method of Inspection Critical
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- NAVYMILT60680A1993THRUSTERCARTRIDGEACTUATEDM16REMANUFACTUREDMETALPARTSASSEMBLYM16 改造 金属 零件 集合 动弹 药筒 推进器

链接地址:http://www.mydoc123.com/p-982791.html