NAVY MIL-STD-2003-5 A-2009 ELECTRIC PLANT INSTALLATION STANDARD METHODS FOR SURFACE SHIPS AND SUBMARINES (CONNECTORS)《水面舰船和潜艇的电气设备安装标准方法(连接器)》.pdf
《NAVY MIL-STD-2003-5 A-2009 ELECTRIC PLANT INSTALLATION STANDARD METHODS FOR SURFACE SHIPS AND SUBMARINES (CONNECTORS)《水面舰船和潜艇的电气设备安装标准方法(连接器)》.pdf》由会员分享,可在线阅读,更多相关《NAVY MIL-STD-2003-5 A-2009 ELECTRIC PLANT INSTALLATION STANDARD METHODS FOR SURFACE SHIPS AND SUBMARINES (CONNECTORS)《水面舰船和潜艇的电气设备安装标准方法(连接器)》.pdf(189页珍藏版)》请在麦多课文档分享上搜索。
1、 INCH-POUND MIL-STD-2003-5A(SH) 3 September 2009 SUPERSEDING DOD-STD-2003-5(SH) 24 June 1987 DEPARTMENT OF DEFENSE STANDARD PRACTICE ELECTRIC PLANT INSTALLATION STANDARD METHODS FOR SURFACE SHIPS AND SUBMARINES (CONNECTORS) Provided by IHSNot for ResaleNo reproduction or networking permitted without
2、 license from IHS-,-,-MIL-STD-2003-5A(SH) ii FOREWORD 1. This standard is approved for use by the Naval Sea Systems Command, Department of the Navy, and is available for use by all Departments and Agencies of the Department of Defense. 2. This standard disseminates up-to-date information detailing r
3、equirements for standard installation methods employed for submarine and surface ship electrical distribution systems. 3. These criteria apply to work on a specific ship or ships only when invoked by the Ship Specifications or similar contractual documents. 4. These criteria are for application to n
4、ew construction, conversion, and alteration of existing ships. 5. Considering the magnitude of this standard, along with the changing requirements imposed on the Electric Plant, it is inevitable that changes will be required to update these criteria. Therefore, as comments arise, they should be forw
5、arded to Naval Sea Systems Command (NAVSEA) 05Z3 to keep this standard as current as possible through subsequent revisions. Revisions will be accomplished by the issuance of additional or revised figures to be inserted in the basic standard parts. Superseded pages may be retained for reference if so
6、 desired. 6. Comments, suggestions, or questions on this document should be addressed to Commander, Naval Sea Systems Command, ATTN: SEA 05M2, 1333 Isaac Hull Avenue, SE, Stop 5160, Washington Navy Yard DC 20376-5160 or emailed to CommandStandardsnavy.mil, with the subject line “Document Comment”. S
7、ince contact information can change, you may want to verify the currency of this address information using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-2003-5A(SH) iii CONTENTS PARAG
8、RAPH PAGE 1. SCOPE1 1.1 Scope.1 1.1.1 Application.1 2. APPLICABLE DOCUMENTS 1 2.1 General1 2.2 Government documents 1 2.2.1 Specifications, standards, and handbooks 1 2.3 Order of precedence1 3. DEFINITIONS .1 4. GENERAL REQUIREMENTS2 4.1 Instructions for use of MIL-STD-2003-52 5. DETAILED REQUIREME
9、NTS.2 6. NOTES .2 6.1 Intended use 2 6.2 Acquisition requirements 2 6.3 Designation of electric plant installation standard methods figures2 6.4 Subject term (key word) listing.3 6.5 Changes from previous issue 3 APPENDIX A Cable Lead Preparation .4 APPENDIX B MIL-C-81511 Series 1 and 2 Gang Contact
10、 Release Connector Assembly Procedure .88 APPENDIX C MIL-DTL-5015 Connectors 112 APPENDIX D MIL-DTL-26482 Connectors 132 APPENDIX E MIL-DTL-28840 Connectors 145 APPENDIX F MIL-DTL-27599 Connectors 155 APPENDIX G MIL-DTL-22992 Connectors 165 APPENDIX H MIL-DTL-38999 Connectors 172 Provided by IHSNot
11、for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-2003-5A(SH) 1 1. SCOPE 1.1 Scope. This standard covers standard methods for connector fabrication on surface ships and submarines. 1.1.1 Application. These installation methods are to be used by all installing act
12、ivities. These methods do not identify ship or type but do establish minimum standards of acceptance for Naval ships. It is the responsibility of the user activity to determine which method satisfies their requirements. It does not authorize relaxation of any requirement specifically invoked by new
13、construction, conversion, overhaul, or refurbishment contracts. In instances where deviated design requirements (for example, ship type, ship class, and so forth) conflict with the requirements of this standard, the requirements of this standard govern. Any deviation for electric plant installation
14、identified in this standard is to be submitted to NAVSEA 05Z3 for resolution. 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3, 4, or 5 of this standard. This section does not include documents cited in other sections of this standard or recommend
15、ed for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in sections 3, 4, or 5 of this standard, whether or not they are listed. 2.2 Governme
16、nt documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF D
17、EFENSE SPECIFICATIONS MIL-DTL-5015 - Connectors, Electrical, Circular Threaded, AN Type, General Specification for MIL-DTL-22992 - Connectors, Plugs and Receptacles, Electrical, Waterproof, Quick Disconnect, Heavy Duty Type, General Specification for MIL-DTL-26482 - Connectors, Electrical, (Circular
18、, Miniature, Quick Disconnect, Environment Resisting), Receptacles and Plugs, General Specification for MIL-DTL-27599 - Connectors, Electrical, Circular, Miniature, High Density, Quick Disconnect, Environment Resistant, Solder Contacts, General Specification for MIL-DTL-28840 - Connectors, Electrica
19、l, Circular, Threaded, High Density, High Shock, Shipboard, Class D, General Specification for MIL-DTL-38999 - Connectors, Electrical Circular, Miniature, High Density, Quick Disconnect (Bayonet, Threaded and Breech Coupling), Environment Resistant, Removable Crimp and Hermetic Solder Contacts, Gene
20、ral Specification for MIL-C-81511 - Connectors, Electrical, Circular, High Density, Quick Disconnect, Environment Resisting: and Accessories General Specification for (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order
21、Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this do
22、cument, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. DEFINITIONS Refer to figure 5A12. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-2003-5A(SH) 2 4. GENERAL REQUIREMENTS 4.1 Instruct
23、ions for use of MIL-STD-2003-5. This standard is designed to be utilized by a connector assembly technician and is formatted to be utilized as follows: a. Determine the governing specification for the connector being assembled. b. Proceed to the applicable Connector Assembly Procedure (figure 5B1, 5
24、C1, and so forth) and review to determine tools and materials required. Each group is designed to assemble a connector starting with the basic components and proceeding in a step-by-step manner to the completed assembly. c. Instructions shown on figures 5A1 through 5A14 identify a sequence of proces
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- NAVYMILSTD20035A2009ELECTRICPLANTINSTALLATIONSTANDARDMETHODSFORSURFACESHIPSANDSUBMARINESCONNECTORS 水面

链接地址:http://www.mydoc123.com/p-982363.html