NAVY MIL-STD-1322-73-1987 UNIT LOAD FOR DOMESTIC AND OVERSEAS SHIPMENT CARTRIDGE CALIBER 38 SPECIAL BALL STEEL JACKETED WITH TRACER IN AMMUNITION BOX M2A1《口径为38的特殊球状弹药筒 有含追踪器的钢壳 用于.pdf

《NAVY MIL-STD-1322-73-1987 UNIT LOAD FOR DOMESTIC AND OVERSEAS SHIPMENT CARTRIDGE CALIBER 38 SPECIAL BALL STEEL JACKETED WITH TRACER IN AMMUNITION BOX M2A1《口径为38的特殊球状弹药筒 有含追踪器的钢壳 用于.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-STD-1322-73-1987 UNIT LOAD FOR DOMESTIC AND OVERSEAS SHIPMENT CARTRIDGE CALIBER 38 SPECIAL BALL STEEL JACKETED WITH TRACER IN AMMUNITION BOX M2A1《口径为38的特殊球状弹药筒 有含追踪器的钢壳 用于.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-STD-13 22-73 (NAVY) MILITARY STANDARD UNIT LOAD 28 MAY 1987 FOR DOMESTIC AND OVERSEAS SHIPMENT CARTRIDGE, CALIBER, .38 SPECIAL BALL, STEEL JACKETED WITH TRACER IN AMMUNITION BOX M2A1 UNIT LOAD DATA WDICIHALC NUBER OF CARTRIDGES PER BOX 1200 NUtfER OF BOXES PER UNIT LOAD . 56 GROSS UEIGHT OF ONE

2、BOX . 90 LBS WEIGHT Cf STEEL STRAPPING 8 LBS MIGHT OF PALLET 90 LES GROSS MIGHT OF UNIT LOAD 2,364 LSSA CmE. . 25.2 CU FT &O NOT USE FOR SHIPPING MIGHT DO NOT STACK HORE THAI 9 UNIT LOADS HIGH IN STORAGE MIGHT OF WOOD DUNNAGE, . 26 LBS - OOT . .CLASS C EXPL CONTAINER SHIPPING AND STORAGE CM 53711 -

3、5167966 CG CLASS I - MSC NO. - N/A APPROVED FOR PUELiC REUSE: DISTRIBUTION IS UNLiHiTED . NOTES: 1. UNLESS OTHERWISE SPECIFIED. DIMENSIONS ARE IN INCHES. 2. FOR CROSS REFERENCE TO ASSOCIATED TRUCKLOADING. CONTAINERLCNDING AND CARLOADING MILITARY STANDARDS, REFER TO INDEX TO STANDARDS HIL-HDK-236 (NA

4、VY 1. THIS UNIT LOAD IS AUTHORIZED AND RELEASED FOR DEPOT HANDLING AND* STORAGE AND FOR SHKYENT bY COMMQN CAWER. 1 FSC 8140 REQUIREMENTS FOR CONSTRUCTION OF THIS UNCT LOAD SHAU CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF MIL-STD-1322 (NAVY) 28 WPNSTA EARLE, NEW JERSEY I PAGE, DATE : NAVAL WEAPO

5、NS HANDLING CENTER Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-M IL-STD-13 22-7 3 (NAVY) PALLETIZING PROCEDURE (A) THREAD EN0 STRAPPING. ITEM 2. TWOUGH SLOTS IN PALLET DECK. ITEM i. ANO CENTER STRAP. ITEM 2. IS PLACED ON PALLET DECK. AS SHOWN IN

6、DETAIL A. PLACE DECK PANEL,ITEM 10, ON PALLET DECK WITH EQUAL OVERHANG ON EACH SIDE. POSITION THE CONTAINERS ON THE DECK PANEL UITH CLOSURES IN ONE DIRECTION. POSITION STRAPPING. ITEM 3. UNDER THE PALLET DECK AND AROUND THE UNIT LOAD. TENSION AND DOUBLE NOTCH SEAL. ITEM 5. (6) (Cl (0) (E) POSITION S

7、TRAPPING. ITEM 2, AROUND THE END PANEL ASSEIIBLY. THE CLEATS OF THE END PANEL MUST BE POSITIONED AGAINST THE LOUER SECTION OF THE CONTAINERS AS SHOWN. DOUBLE NOTCH SEAL. POSITION THE GIRTHUISE STRAPPING, ITEM q, OVER THE SECOND CLEAT OF THE END PANEL ASSEIIBLY. AS SHOWN. TENSION AND DOUBLE NOTCH SEA

8、L. SECURE THE GIRTHUISE STRAPPING TO THE END PANEL ASSEWLY WITH STAPLES. ITEM 6. MRKING: TENSION THE STRAPPING AND (FI (G) THE UNIT LOAD SHALL BE MRKED IN ACCORDANCE WITH THE GENERAL DOCUHENT MIL-STD-1322. A PLACE CENTER STRAP ON PALLET DECK AND UNDER DECK PANEL (1 PLACE) - THREAD END STRAPPING THRO

9、UGH PALLET SLOTS - DETAIL A (2 PLACES) PAGE 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-c MIL-STD-1322-73 (NAVY END PANEL ASSEMBLY I2 mw DETAIL B NOTES: 1. UNLESS OTHERWISE SPECIFIED. MATERIAL SHALL BE IN ACCORDANCE WITH THE GENERAL DOCUMENT MI

10、L-STD-1322. O0 NOT USE TYPE 1 STRAPPING WITH POUER MACHINES. WHEN MIL-P-15011 PALLET IS NOT AVAILABLE. WOOD PALLET NN-P-71. TYPE V. SIZE 2. GROUP II. III OR IV MY BE USED. 2. 3. DEPALLETIZING PROCEDURE (A) REMOVE STAPLES. (6) CUT AND REWVE STRAPPING. (C) REMOVE END PANELS. (D) REIIOVE CONTAINERS. REVIEW ACTIVITY: NAVY - OS PREPARING ACTIVITY: tl4VY - os (PROJECT NO. 8190-N667) PAGE 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-