NAVY MIL-P-24380 B-1989 PAINT ANCHOR CHAIN SOLVENT TYPE GLOSS BLACK (METRIC)《(公制)锚链的黑色光泽溶剂型油漆》.pdf

《NAVY MIL-P-24380 B-1989 PAINT ANCHOR CHAIN SOLVENT TYPE GLOSS BLACK (METRIC)《(公制)锚链的黑色光泽溶剂型油漆》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-P-24380 B-1989 PAINT ANCHOR CHAIN SOLVENT TYPE GLOSS BLACK (METRIC)《(公制)锚链的黑色光泽溶剂型油漆》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、- MIL-P-24380B BO 9 777790b OIIOqi.135 II 9 c-/-c3cp-g/ A -I _- pEq MIL-P-24380B(SH) 25 January 1989 SUPERSEDING 21 November 1977 (See 6.9) DOD-P-24380A(SH) MILITARY SPECIFICATION PAINT, ANCHOR CHAIN, SOLVENT TYPE, GLOSS BLACK (METRIC) This specification is approved for use within the Naval Sea Syst

2、ems Command, Department of the Navy, and is available for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification establishes the requirements for a fast drying, solvent type, gloss black paint for application on steel anchor chains. 1.2 Classificatio

3、n. The paint shall be of the following types, as specified (see 6.2.1): Type I - Paint with non-photochemically reactive solvents Type II - Paint with maximum solvent amount of 340 grams (see 3.3.1.1). per liter (see 3.3.1.2). 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications an

4、d standards, The following specifications and standards form a part of this specification to the extent specified herein Unless otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supple

5、ment thereto, cited in the solicitation. SPECIFICATIONS FEDERAL PPP-F-320 PPP-P-1892 - Paint, Varnish, Lacquer, and Related Materials; - Fiberboard; Corrugated and Solid,- Sheet Stock (Container Grade), and Cut Shapes. Packaging, Packing, and Marking of. Beneficial comments (recommendations, additio

6、ns, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Commander, Naval Sea Systems Command, -SEA 5523, Department of the Navy, Washington, DC 20362-5101 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) app

7、earing at the end of this document or by letter. FSC 8010 AMSC N/A DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. / THIS DOCUMENT CONTAINS /g/ PAGES. I 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NIL-P-2438OB

8、80 993990b OLO4Y3b 3 MIL-P-24380B(SH) MI LI TARY MIL-F-16884 - Fuel, Naval Distillate, MIL-L-19140 - Lumber and Plywood, Fire-Retardant Treated. STANDARDS FEDERAL FED-STD-141 - Paint, Varnish, Lacquer and Related Materials: Methods of Inspection, Sampling and Testing. FED-STD-313 - Material Safety D

9、ata, Transportatipn Data and Disposal Data for Hazardous Materials Furnished to Government Activities. . FED-STD-595 - Colors, 2.1.2 Other Government document. The following other Government document forms a part of this specification to the extent specified herein. Unless otherwise specified, the i

10、ssues shall be those in effect on the date of the solicitation, DEPARTMENT OF LABOR Code of Federal Regulations (CFR) 29 CFR, Part 1910.1200 - Hazard Communication Standard. (The Code of Federal Regulations (CFR) and the Federal Register (FR) are for sale on a subscription basis by the Superintenden

11、t of Documents, U.S. Government Printing Office, Washington, DC 20402. When indicated, reprints of certain regulations may be obtained from the Federal agency responsible for issuance thereof. ) (Copies of specifications, standards and other Government documents required by contractors in connection

12、 with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting activity.) 2.2 Other Dublications. The following documents form a part of this speci- fication to the extent specified herein. Unless otherwise specified, the issues of the documen

13、ts which are DoD adopted shall be those listed in the issue of the DoDISS specified in the solicitation. Unless otherwise specified, the issues of documents not listed in the DoDISS shall be the issue of the non-government document which is current on the date of the solicitation, AMERICAN SOCIETY F

14、OR TESTING AND MATERIALS (ASTM) A 108 - Standard Specification for Steel Bars, Carbon, Cold- Finished, Standard Quality. (DoD adopted) B 117 - Standard Method of Salt Spray (Fog) Testing. (DoD adopted) D 93 Closed Tester. (DoD adopted) D 1200 - Standard Test Method for Viscosity of Paints, Varnishes

15、, and Lacquers by Ford Viscosity Cup. - Standard Test Methods for Flash Point by Pensky-Martens (DoD adopted) 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-flIL-P-Zi380B 80 9 7777906 0304437 5 Sll MIL-P-24380B(SH) ASTM (Continued) D 1644 - Standa

16、rd Test Methods for Nonvolatile Content of D 1849 - Standard.Test Method for Package Stability of Paint. D 1951 - Standard Test Method for Ash in Drying Oils and Fatty D 3359 - Standard Test Methods for Measuring Adhesion by Tape Varnishes. (DoD adopted) (DoD adopted) Acids. (DoD adopted) Test. (DoD

17、 adopted) (Application for copies should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.) (Nongovernment standards and other publications are normally available from the organizations which prepare or which distribute the documents. documents

18、 also may be available in or through libraries or other informational services.) These 2.3 Order of Precedence. In the event of a conflict between the text of this specification and the references cited herein (except for associated detail specifications, specification sheets or MS standards), the t

19、ext of this specifi- cation shall take precedence. Nothing in this specification, however, shall supersede applicable laws and regulations unless a specific exemption has been obtained . 3. REQUIREMENTS 3.1 First article. When specified in the contract or purchase order, a sample shall be subjected

20、to first article inspection (see 4.3 and 6.3). 3.2 Material. 3.2.1 Formula. The paint shall be composed of chlorinated rubber and plasticizer dissolved in solvents. 3.3.1. Carbon tetrachloride and benzene shall not be used. Asbestos and components containing asbestos are prohibited, order, a certifi

21、cate of compliance shall be prepared (see 6.2.2). Solvents shall conform to the requirements of When specified in the contract or 3.2.2 Recovered materials. Unless otherwise specified herein, a11 material incorporated in the paint covered by this specification shall be new and may be formulated usin

22、g materials produced from recovered materials to the maximum extent practicable without jeopardizing the intended use. The term “recovered materials“ means materials which have been collected or recovered from solid or liquid waste and reprocessed to become a source of raw materials, as opposed to v

23、irgin raw materials. use of used products is allowed under this specification unless otherwise specifically specified. None of the above shall be interpreted to mean that the 3.2.3 Toxicity. The material shall have no adverse effect on the health of personnel when used for its intended purpose (see

24、4.2.2). The manufacturer of the material shall disclose the formulation of his product to the Navy Bureau of .Medicine and Surgery, Navy Department, Washington, DC 20372. This disclosure of 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-proprietar

25、y information, which will be held in confidence by the Bureau of Medicine and Surgery, shall include: the name, formula, and approximate per- centage by weight and volume of each ingredient in the product; the results of any toxicological testing of the product; identification of its pyrolysis produ

26、cts; and any other information that may be needed to permit an accurate appraisal of any toxicity problem associated with the handling, storage, applica- tion, use, or disposal of material, Questions pertinent to this effect shall be referred by the contracting activity to the Naval Medical Command

27、(NAVMEDCOM) which will act as advisor to the contracting activity. 3.2.4 Material safetv data sheet. The contracting activity shall be provided a material safety data sheet (MSDS) at the time of the contract award. The MSDS shall be provided in accordance with the requirements of FED-STD-313 and 29

28、CFR 1910.1200, Hazard Communication Standard. When FED-STD-313 is at variance with the CFR, 29 CFR 1910.1200 shall take precedence. modified and supplemented accordingly, shipment of the material covered by this specification (see 6.7). FED-STD-313 shall be The MSDS shall be included with each 3.3 Q

29、uantitative requirements. The paint shall conform to the quantitative requirements shown in table I and as specified herein. TABLE I. Quantitative reuuirernents. Character is tic Ash content, percent by weight of paint Viscosity, no. 4 Ford cup at 25C (77“F), seconds Nonvolatile matter, percent by w

30、eight of paint Matter insoluble in hot toluene, percent by weight of paint Flash point, “C(“F) Draining time, minutes Drying time - set to touch, minutes dry hard, minutes Requirements Minimum Maximum 5 40 40 5 -_ 5 15 60 3.3.1 Solvent. The solvent shall conform to the requirements herein specified.

31、 3.3.1.1 Type I solvent shall conform to the following requirements: (a) A combination of hydrocarbons, alcohols, aldehydes, ethers, 5 percent maximum. esters, or ketones having an olefinic or cycloolefinic type of unsaturation except perchloroethylene: atoms to the molecule except ethylbenzene, met

32、hyl benzoate, and phenyl acetate: 8 percent maximum. carbon structures, trichloroethylene, or toluene: 20 percent maximum. (b) A combination of aromatic compounds with eight or more carbon (c) A combination of ethylbenzene, ketones having branched hydro 4 Provided by IHSNot for ResaleNo reproduction

33、 or networking permitted without license from IHS-,-,-3.3.1.2 Type II paint shall have a maximum volatile organic content (less water) of 340 grams per liter. 3.4 Oualitative requirements. The paint shall conform to the qualitative O requirements specified herein. 3.4.1 Dry oDacity. A maximum of 7.0

34、 milliliters (mL) per 0.948 square meter of the paint shall be required to obtain a dry film contrast ratio of 0.92 (see 4.5.9). 3.4.2 Color and gloss. The color and gloss of the paint shall match the dry color chip no. 17038 of FED-STD-595 (see 4.5.10). 3.4.3 ApDearance. The material shall appear s

35、mooth, uniform, and free from dirt, grit, clots, gel bodies, or other insoluble matter (see 4.5.11). 3.4.4 Heat resistance. The dry film shall not deform, blister, crack, emit . odors, or exhibit any visible evidence of deterioration and shall show no transfer of paint (see 4.5.12). 3.4.5 Salt spray

36、 resistance. .milligrams dissolved iron (see 4.5.13). Test specimens shall show a maximum of 3.0 3.4.6 Oil resistance. The dried paint film shall show no loss of adhesion (see 4.5.14). 3.4.7 Adhesion. The dried paint film shall show no loss of adhesion (see a 4.5.15). 3.4.8 Stability. 3.4.8.1 Filled

37、 containers. The paint, as received in its filled original container, shall be readily mixable, either by paddle, shaker, or mechanical stirrer, to a smooth, uniform consistency and shall conform to all requirements as specified herein. The paint shall not curdle, liver, gel, seed or develop any oth

38、er objectionable properties for a minimum of 1 year after date of manufacture (see 4.5.16.1). year after manufacture, may t packed level A, B, or C as specified (see 6.2.1) and marked (see 3.5) in accordance with PPP-P-1892 and shall include bar codes, flash point marking and applicable packaging ac

39、quisition options therein as specified (see 6.2.1). In addition, for Navy acquisitions, the following applies: (a) Navy fire-retardant requirements. (1) Treated lumber and Dlvwood. When specified (see 6.2.1), all lumber and plywood including laminated veneer material used in shipping container and p

40、allet construction, members, blocking, bracing, and reinforcing shall be fire-retardant treated material conforming to MIL-L-19140 as follows: Level A and B - Type II - weather resistant Level C - Type I - non-weather resistant Category 1 - general use. Category 1 - general use. (2) Fiberboard, When

41、 specified (see 6.2.1), fiberboard used in the construction of class-domestic, non-weather resistant fiberboard, and cleated fiberboard boxes including interior packaging forms such as die-cuts, cells, pads, separators, and partitions where required shall meet the flame spread index and the specific

42、 optic density requirements of PPP-F-320 and amendments thereto. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-24380B 0 W 7777706 0104446 6 W MIL-P-24380B(SH) t 5.2 Material safety data sheet, A copy of the material safety data sheet shall be

43、 attached to the shipping document for each destination (see 3.2.4). 6. NOTES 6.1 Intended use. This paint is intended for use as a coating for steel anchor chains. This product may be applied where air pollution regulations apply 6.2 Ordering data, 6.2.1 Acauisition reauirements. Acquisition docume

44、nts should specify the f o1 low ing : Title, number, and date of this specification. Type required (see 1.2). First article sample, when required (see 3.1). Identification markings required (see 3.5). Inspection conditions, if other than as specified (see 4.2.1). When ingredients are to be provided

45、for test purposes (see 4.4.5). Level of packaging and level of packing required (see 5.1). Size of container required (see 5.1). When fire-retardant requirements are not required (see 5.1). Bar codes, flash point marking, and packaging acquisition options When fiberboard shall meet the flame spread

46、index and specific (see 5.1). optic density requirements of PPP-F-320 (see 5,1(a). 6.2.2 Consideration of data requirements. The following Data Item Descrip- tions (DIDs) must be listed, as applicable, on the Contract Data Requirements List (DD 1423) when this specification is applied on a contract,

47、 in order to obtain the data, except where DOD FAR Supplement 27.475-1 exempts the require- ments for a DD 1423. Reference paragraph DID number DID title %nested - tailoring 3.2.1 4.3 4.3 DI-E-2121 Certificate of compliance DI-T-4901 First article inspection procedure DI-T-4902 First article inspect

48、ion report - The above DIDs were those cleared as of the date of this specification. current issue of DOD 5010.12-L, Acquisition Management Systems and Data Require- ments Control List (AMSDL), must be researched to ensure that only current, cleared DIDs are cited on the DD 1423. The 6.3 First artic

49、le. When a first article inspection is required, the item should be a first article sample. The contracting officer should include specific instructions in acquisition documents regarding arrangements for examinations, approval of first article test results and disposition of first articles. Invitations for bids should provide that the Government reserves the right to waive the requirement for samples for The first article should consist of one unit. Provided by IHSNot for Resa